Revision 1.0. Released on 19th of February, 2013.
STEP 4: INSTALLING THE MOUNTING PLATE:
STEP 5: FINISHING THE INSTALLATION
Screw in the four (4) rubber vibration dampers into the threaded holes on the
bottom side of the reservoir. Do not use any tools to fasten the dampers in to
position, use thumbs only.
Then use enclosed M4x4 DIN 7984 screws to install the metal plate on the
reservoir using enclosed Allen key 2.5mm.
Secure the metal plate through the openings to the computer chassis using
enclosed M4x6 ISO7380 screws, washer and M4 nut. User may need to drill 4
(four) Φ4mm holes through chassis metal using electric power drill if there are
no appropriate mounting holes available.
The EK-XRES DCP 2.2 offers three inlet (suction) G1/4 ports. In order to use
the selected port as inlet it is mandatory to use the enclosed EK-Extender G1/4
with the G/4 threaded fitting. Use enclosed G1/4 Plugs to plug the remaining
two unused ports. In order to make air bleeding process easier one can install
the enclosed PU mesh in the inlet compartment of the XRES.
STEP 6: CONNECTING YOUR RESERVOIR
Connect two G1/4 threaded fittings to the reservoir (IN / suction) and pump (OUT / pressure). Please note the water flow orientation.
EKWB
recommends using EK-CSQ fittings and EK-CSQ Adapters with the EK-XRES DCP 2.2 series reservoirs. To ensure that the tubes are securely attached to the
barb/fittings, please use hose clamps or an appropriate substitute.
STEP 5: FILLING THE RESERVOIR
Unscrew the top cap and fill the coolant in the reservoir. Make sure the liquid is not spilled over your computer or any electrical devices nearby. Run your pump
shortly for couple of times to make sure water floods your tubes and other water cooling components. Repeat the procedure until you are done and pay attention
to the water level in your reservoir. Lowest level of the coolant should be at least 1 cm above the plastic (Acetal) base of the reservoir. The highest
recommendable water level is approximately 0.5cm below the top of the acrylic tube. Once done with the filling process please close your EK-XRES DCP 2.2 by
reinstalling the end cap, twisting it clock-wise.
STEP 5: OTHER INSTRUCTIONS
VERY IMPORTANT NOTICE: Once the installation is completed, it is a recommended practice to test the cooling circuit for leaks prior to powering up the computer. We recommend a 24 hour leak test prior to powering
up the computer. Do not test the product using tap water pressure. This will rupture the top of the housing and render the product unusable (and will void your warranty). While all efforts have been made to provide the
most comprehensive tutorial possible, EK Water Blocks assumes no liability expressed or implied for any consequential damage(s) occurring to your equipment as a result of using EK Water Blocks cooling products, either
due to errors or omissions on our part in the above instructions, or due to failure or defect in the EK Water Blocks cooling products.
WARRANTY: Our products are warranted against defects in materials or workmanship for a period of 24 months beginning from the date of delivery to the final user. During this period, products will be repaired or have
parts replaced at our discretion provided that: (I) the product is returned to the agent from whom it was purchased; (II) the product has been purchased by an end user and has not used for commercial purposes; (III) the
product has not been misused, handled carelessly, or used in a manner other than in accordance with the instructions provided describing its installation and proper use. This warranty does not confer rights other than
those expressly set out above and does not cover any claims for consequential loss or damage. This warranty is offered as an extra benefit and does not affect your statutory rights as a consumer. This warranty is voided if
the product comes in contact with aggressive UV additives or other improper liquids.
philips head screwdriver power drill with 4mm drill bit (optional)
