Elation DLED Par Zoom User manual

Rev. 07/20/2010 –visage Version 1.2
DLED Par Zoom
Elation Professional™
6122 S. Eastern Ave.
Los Angeles, Ca 90040
www.elationlighting.com

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 1www.ElationLighting.com

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 2www.ElationLighting.com
TABLE OF CONTENS
1. General Information……………………………………………………………………… 3
a. Introduction……………………………………………………………………….3
b. Unpacking………………………………………………………..…………..… 3
c. Customer Support…………………………………………….………………… 3
d. Warranty Registration……………………………………………………..…… 3
2. Safety Instructions………………………………………………………........………….5
3. Features……………………………………………………………………………………7
4. General Guidelines……………………………………………………………………….8
5. Fixture Overview………………………………………………………………………….9
6. Mounting and Installation………………………………………………………….…….11
7. Understanding DMX……………………………………………………………………...14
a. DMX Cables……..……………………………………………………………….14
b. DMX Terminator………………………………………………………………….15
c. 3-Pin to 5-Pin Conversion……………………………………………………….16
8. Display Indicators….……………………………………………………..……………… 18
9. Display Menu….……………………………………………………..……………………19
10. DMX Addressing…………………………………………………….…………………… 25
a. Remote DMX Addressing (RDMX)…………………………………………….25
11. DMX Traits…………………………………………………………………………………27
12. Working with Built-In programs………………………………………………………….31
13. Barn Door / Gel Frame Installation……………………………………………….…….34
14. Cleaning and Maintenance………………………………………………………………35
15. Warranty…………………………………………………………………………………...36
16. Photometric Data………………………………………………………………………… 38
17. Dimensional Drawings………………………………………………….……………….. 40
18. Circuit Schematic………...……………………………………………………………….41
19. Technical Specifications…………………………………………...………….………… 42

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 3www.ElationLighting.com
1. GENERAL INFORMATION
INTRODUCTION: Congratulations, you have just purchased one of the most innovative and
reliable LED fixtures on the market today! The DLED PAR ZOOM™ has been designed to
perform reliably for years when the guidelines in this booklet are followed. Please read and
understand the instructions in this manual carefully and thoroughly before attempting to
operate this unit. These instructions contain important information regarding safety during
use and maintenance.
UNPACKING: Thank you for purchasing the DLED PAR ZOOM™ by Elation Professional®.
Every DLED PAR ZOOM™ has been thoroughly tested and has been shipped in perfect
operating condition. Carefully check the shipping carton for damage that may have occurred
during shipping. If the carton appears to be damaged, carefully inspect your fixture for
damage and be sure all accessories necessary to operate the fixture have arrived intact. In
the event damage has been found or parts are missing, please contact our customer support
team for further instructions. Inside the box you should find: the fixture, a Power Cable, a
DMX XLR cable, a safety cable, and this manual. Please do not return this unit to your
dealer without first contacting customer support at the number listed below.
CUSTOMER SUPPORT: Elation Professional®provides a customer support line, to provide
set up help and to answer any question should you encounter problems during your set up
or initial operation. You may also visit us on the web at www.elationlighting.com for any
comments or suggestions. For service related issue please contact Elation Professional®.
Service Hours are Monday through Friday 9:00 a.m. to 5:00 p.m. Pacific Standard Time.
Voice: [phone]
Fax: [phone]
E-mail: [email protected]
Forum: www.ElationLighting.com/forum
Warning! To prevent the risk of fire and reduce the risk electrical shock,do not attempt to
operate this fixture with the lens cover removed.
Caution! There are no user serviceable parts inside this unit. Do not attempt any repairs

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 4www.ElationLighting.com
yourself. Doing so will void your manufactures warranty.
Please do not discard the shipping carton in the trash. Please recycle whenever possible.
WARRANTY REGISTRATION: The DLED PAR ZOOM™ carries a two-year (730 days)
limited warranty. Please fill out the enclosed warranty card to validate your purchase. All
returned service items whether under warranty or not, must be freight pre-paid and
accompany a return authorization (R.A.) number. The R.A. number must be clearly written
on the outside of the return package. A brief description of the problem as well as the R.A.
number must also be written down on a piece of paper and included in the shipping
container. If the unit is under warranty, you must provide a copy of your proof of purchase
invoice. Items returned without a R.A. number clearly marked on the outside of the package
will be refused and returned at customer’s expense. You may obtain a R.A. number by
contacting customer support at [phone].

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 5www.ElationLighting.com
2. SAFETY INSTRUCTIONS
To guarantee proper and consistent operation, it is important to
follow the guidelines in
this manual. Elation Professional will not
accept responsibility for damages resulting from the misuse of
this fixture due to the disregard of the information printed in this
manual.
1. Always be sure that the fan and the air inlets remain clean and are never
blocked. Allow about 6” (15cm) between this fixture and other devices or a wall
to allow for proper cooling. See page 12.
2. Never touch the fixture during normal operation.
3. Never look directly into the light source. You risk injury to your retina, which may
induce blindness.
4. For safe operation, follow the Installation guide described in chapter six of this
manual. Operating the DLED PAR ZOOM™ without suited safety aids such as
safety cables or clamps can increase the risk of damage and/or personal injury.
5. Qualified and certified personnel should only perform installation.
6. When mounting this fixture, use only the original rigging points included with this
fixture. Any structural modification will void the original manufactures warranty
and may increase the risk of damage and/or personal injury.
7. Do not attempt to operate this fixture if the power cord has become damaged or
frayed.
8. Never open this fixture while in use.
9. This device falls under protection-class I. Therefore it is essential that the device
be grounded properly.
10.Qualified personnel should perform all electrical connections.
11.Be sure the available voltage matches the voltage requirements of the unit. Be
sure the power cord is never crimped or damaged. If the power cord is damaged,
replace it immediately with a new one of similar power rating.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 6www.ElationLighting.com
12.Always disconnect from main power before performing any type of service or
any cleaning procedure.
13.Only handle the power cord by the plug. Never pull out the plug by tugging the
wire portion of the cord.
14.This fixture is designed for use indoors only, use of this fixture outdoors will void
the manufactures warranty.
15.Please be aware that damages caused by modifications to the device are
not subject to warranty.
Important Notice: Damages resulting from the disregard of safety and general user
instructions found in this user manual are not subject to any warranty claims.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 7www.ElationLighting.com
3. FEATURES
•Lowpower consumption
•Minimal heatemission
•Maintenance free operation
•Equipped with 36 3-Watt (10 x red, 16 x green, 10 x blue)
•Silent Operation, convection cooled, no fans
•100,000 hours rated LED life
•Linear RGB Color Mixing, infinite color possibilities
•Built-In Electronic Zoom (13° ~ 55°)
•USITT DMX-512 Complaint
•Preprogrammed colored macros
•Strobe-effect with a maximum flash rate of 18fps
•DMX-controlled operation or stand-alone operation with Master/Slave-function
•7built-in programs can be called up via DMX-controller
~ 48 preprogrammed scenes per program
•Sound-controlled via built-in microphone
•8 Channel DMX Control
•DMX-control via standard DMX-controller
•Upgradable firmware via Elation “E -Loader” Programming Device
•Electronic Switching Power Supply 100v~240v
•Flicker-free operation for television and film
•Durable Cast Aluminum Case Design
•0%~100% Dimming (two dimming options; linear & standard)
• Optional Accessories:
-Barn Door Assembly
-FrostFilter

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 8www.ElationLighting.com
4. GENERAL GUIDELINES
This fixture is a professional lighting effect designed for use on stage, in nightclubs, in
theatres, and other types of architectural installations. Do not attempt operation or
installation without a proper knowledge on how to do so.
Consistent operational breaks will ensure that the fixture will function properly for many
years to come.
Do not shake the fixture around. Avoid brute force when installing or operating the fixture.
While choosing an installation location, please be sure that the fixture will not be exposed to
extreme heat, moisture, or dust. The minimum distance between the fixture and a wall or flat
surface should be at least0.5 meter (about 1.5ft). See page 11.
Always install the fixture with an appropriately rated safety cable. When installing the fixture
in a suspended environment always be sure to use mounting hardware no less than M10 x
25 mm, also be sure the hardware is only inserted in the yoke’s mounting holes.
Do not attempt to operate this fixture until you have familiarized yourself with all of its
functions.
Do not permit operation by persons not qualified for operating this type of architectural
fixture. Most damages are the result of improper operation.
Please use the original packaging to transport the fixture in for service.
For your own safety, please read this user manual carefully before installing the device.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 9www.ElationLighting.com
5. FIXTURE OVERVIEW
1. Fixture Casing Assembly–Durable cast aluminum casing designed to take the
rigors of touring.
1) Fixture Casing
2) LED Assembly
3) Yoke Assembly
4) Menu Button
5) Up Button
6) Down Button
7) Enter Button
8) Power input
9) DMX Output Jack
10) DMX Input Jack

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 10 www.ElationLighting.com
2. LED Lens Assembly–The lens assembly may be user replaced in the event repair
is needed or a different beam angle is required.
3. Yoke Assembly –Thisyoke is designed to perform two functions; 1) When split it
can be used as a floor stand. 2) Used to secure a mounting clamp for truss mounting.
4. MENU Button –This button is used to access the fixtures menu functions.
5. Up Button –The up button is used to toggle forward through the menu functions and
settings.
6. Down Button –The down button is used to toggle backwards through the menu
functions and settings.
7. Enter Button–The enter button is used to enter in to a certain menu function or to
lock a menu setting in to memory.
8. Main Power Input–This power assembly provides main power to the unit and also
houses the intergraded safety fuse. Be sure to always use an approved power rated
IEC cable to feed power to the unit. In the event of fuse failure, always replace with
the exact same fuse unless otherwise instructed to do so by an authorized Elation
technician.
9. DMX OutJack–3-pin Male XLR connector. This lead is used to send an incoming
DMX signal to the next fixture in the DMX chain. Always use a proper DMX cable for
data transfer
10. DMX In Jack –3-pin Female XLR connector.This lead is the main DMXinput lead.
Always use a proper DMX cable for data transfer

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 11 www.ElationLighting.com
6. MOUNTING AND INSTALLATION
Cautions:
For added protection mount the fixtures in areas outside walking paths, seating areas, and
away from areas were unauthorized personnel might reach the fixture.
Before mounting the fixture to any surface, make sure that the installation area can hold a
minimum point load of 10 times the device’sweight.
Fixture installation must always be secured with a secondary safety attachment, such as an
appropriate safety cable.
To avoid injury, never stand directly below the device when mounting, removing, or servicing
thefixture.
Refer to regulations BGV C1 (formerly VBG 70) and DIN VDE0711-
217
for proper installation in Europe
To ensure proper installation, only
qualified staff should attempt installation.
Mounting points
Overhead mounting requires extensive experience, including amongst others calculating
working load limits, a fine knowledge of the installation material being used, and periodic
safety inspection of all installation material and the fixture. If you lack these qualifications, do
not attempt the installation yourself. Improper installation can result in bodily injury.
CAUTION!
Be sure a qualified electrician performs all electrical
connections.
Be sure to complete all rigging and installation procedures before connecting the main
power cord to the appropriate wall outlet.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 12 www.ElationLighting.com
Mounting
The DLED PAR ZOOM™ is fully operational in any mounting position, hanging upside-down,
side mounted, or set on a flat level surface, etc. Be sure this fixture is kept at least 0.5m (1.5
feet) away from any flammable materials (decoration etc.). When clamp mounting; always
use and install the supplied safety cable as an added safety measure to prevent accidental
damage in the event of a clamp failure.See the image below.
Clamp Mounting
The DLED PAR ZOOM™provides a unique mounting bracket assembly that allows the unit
to stand ona flat surface or to be hung on truss via a clamp in any safe position (see the
illustration above). Regardless of the mounting option you choose pleasebe sure to refer to

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 13 www.ElationLighting.com
thesafety guidelines in this manual to avoid damage to the unit and/or personal injury.
When mounting this fixture to truss be sure to secure an appropriately rated clamp to the
hanging yoke using a M12 screw fitted through the center hole of the hanging yoke. As an
added safety measure be sure to attach at least one properly rated safety cable to the fixture.
See illustrationsbelow.
Securing the DLED PAR ZOOM™
Always be sure to secure your fixture with a safety cable when
suspending the unit from truss or other means. The fixture
provides a built-
in rigging point for a safety cable as illustrated
above. Be sure to only use the designated rigging point for
the
safety cable and never secure a safety cable to the hanging
bracket.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 14 www.ElationLighting.com
7. UNDERSTANDING DMX
DMX-512: DMX is short for Digital Multiplex. This is a universal protocol used by most
lighting and controller manufactures as a form of communication between intelligent fixtures
and controllers. DMX allows all makes and models of different manufactures to be linked
together and operate from a single controller. This is possible as long as all the fixtures and
the controller are DMX compliant. A DMX controller sends the DMX data instructions to a
fixture allowing the user to control the different aspects of an intelligent light. DMX data is
sent out as serial data that travels from fixture to fixture via data “IN” and “OUT” leads
located on the fixtures (most controllers will only have output jacks).
DMX Linking: To ensure proper DMX data transmission, always use proper DMX cables
and a terminator. When using several DMX fixtures try to use the shortest cable path
possible. Never split a DMX line with a “Y” style connector. The order in which the fixtures
are connected in a DMX line does not influence the DMX addressing. For example; a fixture
assigned a DMX address of 1 may be placed anywhere in the DMX chain, at the beginning,
at the end, or anywhere in the middle. The DMX controller knows to send data assigned to
address 1 to that fixture no matter where it is located in the DMX chain. The DLED PAR
ZOOM™ can be controlled via DMX-512 protocol. TheDLED PAR ZOOM™is a fixture that
operates with 8 DMX channels (see pages 28-31 for the different DMX traits). The DMX
address is set electronically using the controls on thebottom of the fixture.
Data Cable (DMX Cable) Requirements (For DMX and Master/Slave Operation): Your
fixture and your DMX controller require a standard 3-pin or 5-pin XLR connector for data
input and data output (the illustration on the next page is of a 3-Pin XLR connector). If you
aremaking your own cables, be sure to use two conductor shielded digital DMX cable rated
at 120 ohms, this cable is designed for DMX transmission and may be purchased from your
Elation dealer or at most professional lighting retailers. Your cables should be made with a
male and female XLR connector on either end of the cable. Also, remember that a DMXline
must be daisy chained and cannot be split, unless using an approved DMX splitter such as
the Elation Opto Branch 4™ or DMX Branch/4™.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 15 www.ElationLighting.com
Be sure to follow the above figure when making your own cables. Do not use the ground lug
on the XLR connector. Do not connect the cable’s shield conductor to the ground lug or
allow the shield conductor to come in contact with the XLR’s outer casing. Grounding the
shield could cause a short circuit and erratic behavior.
DMX-512 control connection
Connect the provided XLR cable to the female 3-pin XLR output of your controller and the
other side to the male 3-pin XLR input of the moving head (Please refer to the diagram
below.). You can chain multiple fixtures together through serial linking. The cable that should
be used is two conductor, shielded DMX cable with XLR input and output connectors.
Always be sure daisy chain your in and out data connections, never split or “Y”your DMX
connections unless you are using an approved DMX splitter such as the Elation Opto Branch
4™ or DMX Branch/4™.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 16 www.ElationLighting.com
DMX-512 connection with DMX terminator
A DMX terminator should be used in all DMX lines especially in longer runs. The use of a
terminator may avoid erratic behavior in your DMX line. A terminator is a 120 ohm 1/4 watt
resistorthat is connected between pins 2 and 3 of a male XLR connector (DATA + and DATA
-). This fixture is inserted in the female XLR connector of the last fixture in your daisy chain
to terminate the line. Using a line terminator (Elation part: DMX T PACK) will decrease the
possibilities of erratic behavior.
5-Pin XLR DMX Connectors. Some manufactures use 5-pin XLR connectors for DATA
transmission in place of 3-pin. 5-pin XLR fixtures may be implemented in a 3-pin XLR DMX
line. When inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must
be used, these adaptors are readily available at most electric stores. The following chart
details a proper cable conversion.
Fixture DMX addressing;
All fixtures should be given a DMX starting address when using a DMX controller, so the
correct fixture responds to the correct control signal. This digital starting address is the
channel number from which the fixture starts to “listen” to the digital control information sent

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 17 www.ElationLighting.com
out from the DMX controller. The allocation of this starting DMX address is achieved by
setting the correct DMX address on the digital display located on theback of the fixture.
You can set the same starting address for all fixtures or a group of fixtures, or set different
address for each individual fixture. Be advised that setting all you fixtures to the same DMX
address will subsequently control all fixtures in the same fashion, in other words, changing
the settings of one channel will affect all the fixtures simultaneously.
If you set each fixture to a different DMX address, each unit will start to “listen” to the channel
number you have set, based on the quantity of control channels (DMX channels) of each
fixture. That means changing the settings of one channel will only affect the selected fixture.
In the case of the DLED PAR ZOOM™,which is a eight channel fixture, you should set the
starting DMX address of the first unit to 1, the second unit to9(8+ 1), the third unit to17 (8+
9), and so on.
Note: During start-up theDLED PAR ZOOM™ will automatically detect whether a DMX data
signal is being received or not. If a DMX data signal is being received, the display will show
"A.XXX" (XXX representing the actual DMX address). If the fixture is not receiving a DMX
signal the display will flash "A.XXX" (XXX representing the actual DMX address).
If your fixture is connected to a DMX controller and the display is flashing (not receiving a
DMX signal), please check the following:
-The 3-pin or 5-pin XLR plug (cable with DMX signal from controller) may not be
connected or is not inserted completely into the DMX input jack.
-The DMX controller is switched off or defective.
-The DMX cable from the controller merging with included IP Rated Cable adapter is
not connected securely
-The DMX cable or connector is defective.
-A DMX terminator has been inserted into the last fixture in your DMX chain.
8. DISPLAY LED INDICATOR.

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 18 www.ElationLighting.com
The DLED PAR ZOOM ™ has a LED indicator on the display. This indicator is designed to
give a quick visual indication of the fixtures’ DMX status. The illustration below details the
functionality of the LED indicators.
The LED indicator represents DMX signal:
• If the indicators is on,a clean DMX signal is present
• If the indicator is off, there is no DMX signal present

DLED Par Zoom™
©Elation Professional, Los Angeles Ca. 19 www.ElationLighting.com
9. DISPLAY MENU
On-Board System Menu: The Design PAR Zoom™ comes with aneasy to navigate system
menu. This next section will detail the functions of each command in the system menu.
LED Control Panel: The control panel located on the base of the fixture allows you to
access the main menu and make all necessary adjustments to the Design Par Zoom™.
During normal operation, tapping the “MENU” key once will access the fixture’s main menu.
Once in the main menu you can navigate through the different functions and access the
sub-menus with the Up and Down buttons. Once you reach a field that requires adjusting,
tap the ENTER button to activate that field and use the UP and Down button to adjust the
field. Tapping the Enter button once more will confirm your setting. Once a setting is saved
the display will briefly readout OK to confirm a new setting has been made and locked into
memory. You may exit the main menu at any time without making any adjustments by
tapping the MENU button.
MENU Button -To access the main menu locate the MENU button on the front of the unit.
Press this button to activate the system menu. Tap the UP button until you reachthe function
you wishto change. When you reach the function you wish to change tap the ENTER button
once to select that menu function. When a function is selected,use the UP or DOWN button
to change the function. Once your changes are made tap the ENTER button yet again to
lock the change in the system menu. To exit without making any changes tap the MENU
button.
VALU A001~XXX
(AXXX) DMX address setting
SLAV ON/OFF
(SLAV) Slavesetting
ADDR
RDMX ON/OFF Change DMX address
via external controller
ALON (AU-A)
Automatic Run in Stand
Alone
AUTO MAST
(AU-M) Automatic Run as Master
0
MODE
RUN
SOUN ALON (SO-A)
Sound-controlled Run
in Stand Alone