Elba EJE-A0435 User manual

JUICE EXTRACTOR
Model: EJE-A0435(WH)
Owner’s Manual
Please read this manual carefully
before operating your set.
Retainitforfuturereference.
Record model number and serial
numberoftheset.
Seethelabelattachedonthesetand
quote this information to your dealer
when you require service.
For The Warranty Terms & Conditions, Please Refer To Warranty Certificate.

IMPORTANT SAFEGUARDS
When using this appliance, basic precautions should always be followed, including the following:
1. Read all instructions before use.
2. Do not use the appliance if the stailess steel grater and filter assembly is damaged.
3. Do not contact the plug or power cord with wet hands.
4. Do not let the plug remains plugged when not in use.
5. Do not immerse power cord, plug or the motor base into water or any other liquids.
6. Do not use this appliance when the plug or power cord is damaged or the plug is not properly
inserted.
7. Never bend or bind the power cord or apply by excessive force, otherwise it may cause damage. If
the power cord is damaged, it must be replaced by the manufacturer or after-sales service center
to avoid hazards.
8. Keep the power cord out of children. Do not let the power cord hang over the edge or the table or
worktop on which the appliance stands.
9. Operate the appliance on a dry and stable surface.
10. Do not carry the appliance during operation.
11. Do not operate the appliance continuously for more than 3 minutes.
12. Do not operate the appliance without any loading.
13. Only use the food pusher as supplied. Never put your fingers or any other sharp objects into the
feeder tube.
14. Do not touch the cutting blades at the bottom of the stailess steel grater and filter assembly.
15. Before removing the juicer cover, switch off and wait for the filter to stop.
16. Always make sure the appliance is properly and completely assembled before operating. The unit
will not turn on unless it is properly assembled.
17. Before disassembling the appliance, switch off the power and wait for the filter to stop operating.
18. Before cleaning the appliance, make sure the control switch have turn to “0” position. Switch off the
power and unplug the plug from wall outlet then slowly remove the parts.
19. This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning use of the appliance by a person responsible for their safety.
20. Children should be supervised to ensure that they do not play with the appliance.
21. This appliance is intended to be used in household and similar applications.
22. Save this instructions for future reference.

DESCRIPTION OF PARTS
1. Food pusher
2. Pulp chute / Juicer cover
3. Stainless steel grater and filter
4. Spout cover
5. Safety locking arms
6. Juice jug cover
7. Juice jug
8. Pulp container
9. Control switch
•0 stop/ no power
•1 low speed
•2 high speed
10. Motor base
11. Light indicator
12. Pulp container base
ASSEMBLE THE APPLIANCE
(Figure 1)
•Place the motor base on a stable surface and
set the pulp container on the pulp container
base.
•Place the spout cover on the motor base with
the spout hole at the right hand side (facing the
direction of the safety locking arms).
•Swivel the spout cover until it fits on the motor
base.

(Figure2)
•Hold the stainless steel grater and filter
assembly as per figure 2.
•Install the stainless steel grater and filter
assembly into the motor base.
•Twist the filter assembly and gently push down
until it is seated on the motor base.
NOTE: The top edge of the grater should not be
higher than the edge of the spout cover when
properly installed.
(Figure3)
•Place the pulp chute/ juicer cover on top of the
spout cover so that the facing of the pulp chute
is on the opposite side of the spout.
•Lock the pulp chute/juicer cover by raising the
safety locking arms until it clicks into the
grooves located on both side of the pulp chute /
juicer cover.
NOTE: Push the saferty locking arms until it “clicks”
otherwise the juice extractor will not operate when
turning on the power.
(Figure4)
•Place the juice jug or a glass under the spout.
•Insert the food pusher into the feeder tube.
•Connect the plug to wall outlet.
NOTE: Do not power on the appliance with food
loaded into the feeder tube!
PREPARATION OF FRUITS AND VEGETABLES
1. Wash the fruits and vegetables that need to be extracted.
2. Peel fruits that have inedible skins such as citrus fruits, pineapples, melons, papayas, etc.
3. Pit all fruits with seeds such as peaches, nectarines, cherries, etc.
4. Cut the fruits and vegetables such as apples, carrots and cucumbers into small pieces.

OPERATING THE APPLIANCE
1. After assembling the appliance, connect the plug into the wall outlet.
2. Power on the appliance and the light indicator will be on (in blue).
WARNING: Before power on the appliance, make sure the control switch is turned to speed “0” (no
power).
3. Turn the switch either to speed ‘1’ or ‘2’ depending on the type of fruits or vegetables that is being
extracted. Soft fruits or vegetables such as berries, melons, cucumbers, tomatoes, etc, should be
extracted on speed “1”. Harder fruits and vegetables such as apples, celery, carrots, etc. should be
extracted at speed ‘2’.
WARNING: Never put any fruits or vegetables in the feeder tube until the appliance is power on.
4. Insert the fruits or vegetables into the feeder tube. Use the food pusher, gently guide the food down to
the spout cover. To extract the maximum amount of juice, always push the food pusher down slowly.
IMPORTANT: DO NOT PLACE HANDS OR FOREIGN OBJECTS INTO THE FEEDER TUBE.
ALWAYS USE THE FOOD PUSHER.
5. Insert the juice jug cover to separate froth from the fresh juice extracted. If you prefer to have juice
with froth, remove the juice jug cover for direct fresh juice pouring.
DISASSEMBLE THE APPLIANCE
IMPORTANT: Before disassembling the appliance, make sure that the control switch is in the ‘0’
position, the plug has been removed from the wall outlet and the motor has completely stopped
operating.
1. Remove the food pusher from the feeder tube.
2. Remove the juice jug.
3. Hold the pulp chute/ juicer cover and lift up the safety locking arms from the grooves on the side of
the pulp chute/ juicer cover.
4. Lift up to remove the pulp chute/ juicer cover.
5. Remove the spout cover (together with the stainless steel grater) by placing one hand under the
spout and another hand holding under the spout cover edge (opposite the spout) and lift it
upwards.
6. Remove the pulp container.
NOTE: Be careful when handling the grater and filter assembly as the as the cutting blades are very
sharp.

CLEANING AND MAINTENANCE
1. Turn the control switch to the speed ‘0’ and wait for the motor to stop operating.
2. Unplug the plug from the wall outlet.
3. Disassemble the juicer (refer to disassemble the appliance).
4. Clean the following parts with soapy water. Amild detergent is recommended to clean the parts.
Rinse the parts well and dry thoroughly.
•pulp container
•pulp chute/ juicer cover
•food pusher
•juice jug
•spout cover
•feeder tube
5. Rinse the stainless steel grater and filter assembly/ cutting blades with clean water. Use the
cleaning brush gently clean away pulp from the filter and cutting blades. If the holes of the filter are
blocked with pulp, soak the filter assembly into hot water to remove the pulp and clean with the
nylon brush again. Allow to dry on a cloth or paper towel before reassembling the juicer.
6. Wipe the motor base and safety locking arms with a soft dry cloth.
HELPFUL HINTS
1. A small amount of lemon juice can be added into the apple juice to prevent juice turning into brown
colour.
2. Do not use bananas or avocados as they do not contain juice and will clog the juicer.
3. Allow the juicer to run for one minute before turning ‘0’ speed to allow any excess juice to be extract
from the pulp.
4. Plastic bag can be put in the pulp container for easy clean-up.
Technical Specifications:
Voltage : AC 220- 240V, 50Hz
Power : 350W