Elba ARIA EH-A9024ST User manual

Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: ARIA EH-A9024ST(SS)

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Please read this instruction carefully. It is advisable to keep this instruction
manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them to
operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the product,
cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children) with
reduced physical, sensory or mental capabilities unless they have been
given supervision or instruction concerning use of the appliance by a
person responsible for their safety.
5. If the power cord or plug in damaged, it must be replaced by the service
centre or a qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with the
voltage stated on the rating plate of the hood.
7. There must be adequate air ventilation of the room when the cooker hood
is used with the cooking appliances with burning gas or other fuels.
8. Ensure that the installation of exhaust complies with the standard of local
building, gas and electrical authorities.
9. Do not ignite flames in the pans.
10.There is a risk of fire if cleaning is not carried out in accordance with this
instruction.

ASSEMBLY INSTRUCTIONS
Please check the following before installation:
Installation of hood must be carried out by an authorized or qualified technician.
For optimum air extraction, avoid having too many windows surrounding the
cooker hood which will cause air convection.
Make sure the hood is in level after installation to avoid oil spill over from the oil
cup collectors.
The optimum height for the installation is between 650 to 750mm which
measure from the bottom of the hood to the top of the hob.
1) Before installing, determine the height between the bottom of the cooker hood
to the top of the hob.
2) Mark the wall to suit all bracket locations.
3) Drill 4 holes with diameter of Ø10mm and 60mm deep. Insert the screw
anchors into the holes. Tighten the mounting bracket with the screws.
4) Hang the hood on the mounting bracket and make sure the hood is in level
from side view and front view.
5) Fix the exhaust ducting on the hood with the screws provided. Make sure the
ducting is not bending less than 90 degree.
6) Install the telescopic decoration cover to the height required.
7) Install the oil cups on the cooker hood.
8) Before connecting to the mains supply, ensure that the mains voltage
corresponds to the voltage stated on the rating plate inside the cooker hood.

PRODUCT DESCRIPTION
1. On/Off Button –To switch the cooker hood in standby mode and turn
off the cooker hood.
2. Fan Delay Off Function –Press this button to schedule 60 seconds
delay to turn off the cooker hood.
3. LED Light Illumination –To switch on/off the LED light.
4. Normal Fan Speed –Press this button to activate normal fan speed.
5. High Fan Speed –Press this button to activate high fan speed.
OPERATING INSTRUCTIONS
1. Press the button and press the button to operate the cooker hood
in normal speed. Press the button to operate the cooker hood in
high speed.
2. When the motor is running, press button to turn off the cooker hood.
(This function does not relate to the LED illumination)
3. Press the button to turn on the LED light of the cooker hood. Press
again to turn off. (This function does not relate to the cooker hood
motor)

CLEANING AND MAINTENANCE
The hood must always be disconnected from the electricity supply before
carrying out the maintenance.
Clean the hood with damp cloth, hot water and mild detergent. Do not use
chemical, steel, wooden or abrasive cleaners to clean the hood.
Clean the oil cups when they are more than half filled to avoid the oil from
spilling.
Remove the filter, wash in hot soapy water, dry and fit back into the hood.
Do not use the hood without the filter installed.
MAIN SPECIFICATION
Rated Voltage : 220-240V/50Hz
Light : 2W x 2
Suction Power : 1,200m³/hr
Motor Power : 220W
Product Dimension : 900mm(W) x 940-1340mm(H) x 399mm(D)
NOTICE
This product must not be disposed together with domestic waste. It has to
be disposed at an authorized place for recycling of electrical and electronic
appliances. By collecting and recycling waste, you help to save natural
resources and make sure the product is disposed in an environmental
friendly and healthy way.