Elba MARS-V2-90 IS-X User manual

MARS-V2-90 IS-X Range Hood
Installation Guide
Operation Manual

IMPORTANT REMINDERS
USE
This range hood has been designed for domestic household use only to
eliminate smoke and odor.
Commercial usage for café’s, restaurants, and other similar
establishments will void the warranty of this product.
Never use the range hood for purposes other than extracting kitchen
smoke and odor.
Never leave high open flames under the hood when it is in operation.
This range hood is not a toy. Please keep children and other unauthorized
persons not instructed to use the hood away from the appliance.
INSTALLATION
The manufacturer will not be held liable for any damages resulting from
incorrect or improper installation.
Installation must be carried out by a qualified and authorized ELBA
Service Technician.
The minimum safety distance between the cooktop and the range hood is
650 millimeters (mm).
Check that the electrical supply from the outlet to which it is to be plugged
in is matching with the requirements of the hood, as indicated by the
product label on the range hood.
The exhaust pipe should have a minimum diameter of 150 millimeters
(mm)
MAINTENTANCE
Switch off and unplug the appliance from the main power supply before
carrying out any maintenance work. (When disconnecting the appliance,
do not pull on the cord as it might cause a short circuit. Instead, hold the
plug and apply pressure on it when pulling from the wall socket.)
Clean the hood using a damp cloth and a neutral liquid detergent.
Clean and/or replace the filters after the specified time period.
There is risk of fire if cleaning is not carried out in accordance with the
guidelines and instructions as highlighted in the section “CLEANING AND
MAINTENANCE”.
LIABILITY
The Manufacturer will not be held liable for any damages incurred as a
result of the improper installation, usage, and maintenance of this product.

INSTALLATION
Important Notes:
The hood should be placed at a
distance of 65-75cm from the
cooking surface for maximum
performance.
The exhaust pipe should have a
minimum diameter of 150
millimeters (mm)
Install the bracket on a hard
and sturdy surface (with bracing
if possible). Make sure that the
surface screws are long enough
to bite into the ceiling and
tightened with enough torque.
Make sure that the range hood
is aligned properly, not tilted in
either a sideward or
front/backward direction.
The ceiling must bear at least
40 kilograms (Kg) of weight.
The thickness of the ceiling
must be ≧30MM,
Installation Steps:
1. Drill one (1) 170mm round hole
in the centre of the ceiling for
the exhaust pipe as seen in pic
2.

*Note that this should be the centre of the Island hood directly below the
cooktop.
2. According to the hanging board, drill 12 pcs of ST6 * 40mm
flat screws that will be used to fix the hanging board onto
the ceiling as seen in pic 2.
3. Then, 8 pcs of M4*10 screws and M4 nuts with gaskets will
be used to connect the angular bar into the hanging board
mounted on the ceiling as seen in pic 2.
4. If the height is not enough to meet the minimum
requirements, an additional section can be added to lower
the body of the range hood.
5. Calculate the length of the angle bar, and use 16 pcs
M4*10 flat screws and M4 nuts with gaskets to connect
another angular bar with the first section.
*Note: The overlap length of angular bar should be at least
100mm to maintain rigidity and stability of the lower
section.
6. Make sure that the exhaust pipe is fitted inside the 170mm
opening as seen in pic 3.
7. Use 4 pcs ST4*8 flat screws to connect the upper/internal
chimney onto the hanging board, then put the external
chimney. Two (2) hooks will be used to hold up the
chimney in order to install the lower sections, as seen in
pic 4.
8. Use 4 pcs ST4*8 flat screws to install the outlet on the
body casing, as seen in pic 5.

9. Hold up the hood and insert it in between the angular bars. Align it
properly and use 16 pcs M4*10 flat screws to mount the body of the hood
to the angular bars, as seen in pic 6.
10.Lower the exhaust pipe onto the duct / outlet of the hood and fasten
properly to make sure that exhaust air does not leak through the sides.
11.Remove the hooks supporting the chimney cover and lower the chimney
cover to finish off the installation.

OPERATION
LCD Display Symbols:
- Timer Indicator
–Lamp Indicator (displayed when range hood is on)
–Speed Indicator
–Power Indicator (displayed when range hood is on)
Touch Pad Operation:
“ Light ” –Press to activate and deactivate light.
(This functions as the –or decrease button in Time / Timer setting)
“Speed ” –Press to activate motor and select speed setting.
(This functions as the + or increase button in Time / Timer setting)
“Power ” –Press to turn the unit on/off.
“Timer ” –This activates 2 functions: Timer and Time Delay.
Time Function
oHold the key for 2-3 seconds
oThe display will flash indicating adjustment mode
oPress the and buttons to adjust desired time
oPress the again to switch adjustment to minute setting
oPress the and buttons to adjust desired time
oPress the again to finalize settings and exit mode

Time Delay –This range hood is equipped with a time delay function
that allows you to set the duration when the hood will shut off after a
certain time period.
oPress the once to activate delay function.
oPress the and to set the time delay.
oPress the again to confirm after the desired time is set.
oThe LCD display will show the remaining time until the unit is
shut off.
CLEANING AND MAINTENANCE
Aluminium Filters
This unit comes equipped with removable
aluminium filters that are to be cleaned on a
regular basis in order to maintain the
performance and longevity of the hood.
Instruction: To remove the filters, press the
clip located at the front, pull down the filters,
and release the clip.
Cleaning the Filters
1. Prepare a large basin with 40-60 degrees Celsius of warm water and
add a mild detergent to mix with the water.
Note: DO NOT use any corrosive detergent when cleaning.
2. Soak the aluminium filters for two (2) to five (5) minutes in the basin to
loosen the build-up of oil and grease.
3. Use a soft brush with fine bristles to gently scrub the aluminium filters.
Apply moderate strength, so as not to damage the filter.
4. Allow the filter to air dry until it is completely free from any moisture.
Recommendation: Clean the filters at least once every month for regular
usage, or more frequently for heavy usage. Visually inspect the filter for
trapped oil and grease on a regular basis in order to maximize the
performance of the hood.
Warranty Exemption: The aluminium filters are a consumable item and are
not covered by the warranty of this item. Any defects caused by the
negligence in cleaning the filters will also void the warranty of the hood.

LED Lights
This unit comes equipped with energy efficient LED bulbs.
Instruction: Please call the service centre for the replacement of the LED
bulb modules. It is suggested that you do not try to replace this yourself, as it
might cause electrical shock.
Warranty Exemption: The incandescent bulbs are a consumable item and
are not covered by the warranty of this item.
Cleaning the Body Casing
Do not use harsh / aggressive chemicals and rough sponges that can damage
the material finish of the range hood.
1. Use a soft damp cloth to wipe the body casing to remove dust particles.
2. After which, use a dry cloth wipe down any excessive moisture left by
the damp cloth.
3. You may use a dedicated stainless steel cleaner (for stainless steel
finishes) to finish off the cleaning process.