Elba FORZA EH-A9021ST User manual

For The Warranty Terms & Conditions, Please Refer To Warranty Certificate
Owner’s Manual
Please read this manual carefully before
operating your set.
Retain it for future reference.
Record model number and serial number
of the set.
See the label attached on the set and
quote this information to your dealer
when you require service.
DESIGNER HOOD
MODEL: FORZA EH-A9021ST(SS)

Please read this instruction carefully. It is advisable to keep this
instruction manual in a safe place for future reference.
SAFETY PRECAUTIONS
1. Keep electrical appliances out of reach from children. Do not let them
to operate the appliances without supervision.
2. To protect against the risk of electrical shock, do not immerse the
product, cord or plug into water or any other liquid.
3. This product is for household and indoor use only.
4. This product is not intended for use by person (including children)
with reduced physical, sensory or mental capabilities unless they
have been given supervision or instruction concerning use of the
appliance by a person responsible for their safety.
5. If the power cord or plug in damaged, it must be replaced by the
service centre or a qualified service technician to avoid hazard.
6. Before installation, check if the mains supply voltage is matched with
the voltage stated on the rating plate of the hood.
7. There must be adequate air ventilation of the room when the cooker
hood is used with the cooking appliances with burning gas or other
fuels.
8. Ensure that the installation of exhaust complies with the standard of
local building, gas and electrical authorities.
9. Do not ignite flames in the pans.
10.There is a risk of fire if cleaning is not carried out in accordance with
this instruction.

ASSEMBLY INSTRUCTIONS
Please check the following before installation:
Installation of hood must be carried out by an authorized or qualified
technician.
For optimum air extraction, avoid having too many windows
surrounding the cooker hood which will cause air convection.
Make sure the hood is in level after installation to avoid oil spill over
from the oil cup collectors.
The optimum height for the installation is between 300 to 350mm
which measure from the bottom of the hood to the top of the hob.
1) Before installing, determine the height between the bottom of the
cooker hood to the top of the hob.
2) Mark the wall to suit all bracket locations.
3) Drill 4 holes with diameter of Ø10mm and 60mm deep. Insert the
screw anchors into the holes. Tighten the screw with the mounting
bracket.
4) Hang the hood on the mounting bracket and make sure the hood is
in level.
5) Fix the exhaust ducting on the hood with the screws provided.
6) Install the telescopic exhaust cover to the height required.
7) Install the oil cups on the cooker hood.
8) Before connecting to the mains supply, ensure that the mains
voltage corresponds to the voltage on the rating plate inside the
cooker hood.

PRODUCT DESCRIPTION
1. On/Off Button –To switch the cooker hood in standby mode and
turn off the cooker hood.
2. Fan Delay Off Function –Press this button to schedule a delay to
turn off the cooker hood.
3. LED Light Illumination –To switch on/off the LED light.
4. Normal Fan Speed –Press this button to activate normal fan
speed.
5. High Fan Speed –Press this button to activate high fan speed.
OPERATING INSTRUCTIONS
1. Press the button and press the button to operate the cooker
hood in normal speed. Press the button to operate the cooker
hood in high speed.
2. When the motor is running, press button to turn off the cooker
hood. (This function does not relate to the LED illumination)
3. Press the button to turn on the LED light of the cooker hood.
Press again to turn off. (This function does not relate to the cooker
hood motor)

CLEANING AND MAINTENANCE
The hood must always be disconnected from the electricity supply
before carrying out the maintenance.
Clean the hood with damp cloth with hot water and mild detergent.
Do not use chemical, steel, wooden or abrasive cleaners to clean the
hood.
Clean the oil cups when they are more than half filled to avoid the oil
from spilling.
Remove the filter, wash in hot soapy water, dry and fit back into the
hood. Do not use the hood without the filter installed.
MAIN SPECIFICATION
Rated Voltage : 220-240V/50Hz
Light : 2W x 2
Suction Power : 1,200m³/hr
Motor Power : 220W
Product Dimension : 900mm(W) x 940-1340mm(H) x 399mm(D)
NOTICE
This product must not be disposed together with domestic waste. It
has to be disposed at an authorized place for recycling of electrical
and electronic appliances. By collecting and recycling waste, you help
to save natural resources and make sure the product is disposed in an
environmental friendly and healthy way.