manuals.online logo
Brands
  1. Home
  2. •
  3. Brands
  4. •
  5. Eldat
  6. •
  7. Receiver
  8. •
  9. Eldat RCL03 Series User manual

Eldat RCL03 Series User manual

RCL03 RCL04
Mini-Empfänger
Mini Receiver
RCL03 (Schutzart Degree of protection IP20)
LED
CH2
CH1
J1
Antenne
Aerial
TA2TA1
RCL03-4101M-01 433,92 MHz, 1 Kanal/channel
RCL03-4102M-01 433,92 MHz, 2 Kanäle/channels
RCL03-5001M-01 868,30 MHz, 1 Kanal/channel
RCL03-5002M-01 868,30 MHz, 2 Kanäle/channels
RCL04 (Schutzart Degree of protection IP65)
LED
CH2
CH1
J1
Antenne
Aerial
TA2TA1
RCL04-4101M-01 433,92 MHz, 1 Kanal/channel
RCL04-4102M-01 433,92 MHz, 2 Kanäle/channels
RCL04-5001M-01 868,30 MHz, 1 Kanal/channel
RCL04-5002M-01 868,30 MHz, 2 Kanäle/channels
J1
Impuls Impulse
EIN/AUS ON/OFF
Totmann
Dead Man's Mode
1
2
3
4
12-24 V
AC/DC
NC1
NC2
NO1
NO2
COM
1
C
O
M
2
IN1
IN2
Impuls-Taster
Impulse button
CH1
Bild/Fig: 1-3
Hinweis: Die Empfangsleistung kann von mehre-
ren Faktoren beeinflusst werden: Standort, ver-
wendeter Sender, nicht entstörte Geräte und
Anlagen, andere Sender im Frequenzbereich,
Wetterlage u. a.
Note: The reception quality can be affected by a
number of factors: location, equipment and systems
without interference suppression, other transmitters
within the frequency range, atmospheric conditions
and other factors.
D
Bedienungsanleitung
Sicherheitshinweise
Bevor Sie den Mini-Empfänger
anschließen und benutzen, lesen Sie
bitte diese Anleitung sorgfältig durch!
Achtung! Beachten Sie die zulässige Versor-
gungsspannung und die maximale Kontakt-
belastung!
Lassen Sie nicht funktionierende Mini-Empfänger
vom Hersteller überprüfen!
Nehmen Sie keine eigenmächtigen Veränderun-
gen an dem Mini-Empfänger vor!
Bestimmungsgemäßer Gebrauch
Das Gerät darf ausschließlich mit Schutzkleinspan-
nung (SELV) betrieben werden und ausschließlich
als Funksteuerung zum Schalten von Geräten mit
Schutzkleinspannung (SELV) verwendet werden.
Der Hersteller haftet nicht für Schäden, die durch
unsachgemäßen oder bestimmungsfremden Ge-
brauch entstehen!
Funktionsweise
Der Mini-Empfänger RCL03/RCL04 kann in einem
Spannungsbereich von 12-24 V AC/DC betrieben
werden.
Je nach Ausführung können über separate
Funkkanäle 1 oder 2 potenzialfreie Relaisausgänge
geschaltet werden.
Es stehen die drei Betriebsarten Impuls (1 Sekun-
de), EIN/AUS (1-Tast-Bedienung) und Totmann zur
Verfügung.
Je Kanal können bis zu 10 verschiedene Sender-
codes von Funksendern gespeichert werden.
Zusätzlich besteht die Möglichkeit, je Kanal einen
externen Impuls-Taster anzuschließen und mit
diesem das jeweilige Relais entsprechend der
gewählten Betriebsart zu schalten.
Lieferumfang
- Mini-Empfänger,
- Befestigungsmaterial (RCL03: Klebepad,
RCL04: Schrauben, Dübel),
- Bedienungsanleitung
Den Mini-Empfänger benutzen
Montieren und anschließen
•Entfernen Sie den Gehäusedeckel.
•Befestigen Sie den Mini-Empfänger mit dem
beiliegenden Befestigungsmaterial an einem
geeigneten Ort.
•Betriebsart wählen:
Achtung! Vor jedem Ändern der Betriebsart
müssen Sie die Versorgungsspannung
abschalten und nach dem Ändern wieder
zuschalten!
Wählen Sie mit dem Jumper J1 die gewünschte
Betriebsart (Bild 1):
J1 in Position 1-2: Impuls (1 Sekunde)
J1 in Position 2-3: EIN/AUS
J1 in Position 3-4: Totmann (Relais schaltet so-
lange, wie die Sendertaste bzw. der externe
Taster gedrückt wird)
Schließen Sie die Versorgungsspannung (12-24V
AC/DC) und die zu schaltenden Schutz-
kleinspannungsverbraucher wie folgt an (Bild 2):
- Versorgungsspannung: IN1, IN2
- Verbraucher 1 (an Relais 1 / Kanal 1):
NO1 - COM1: Schließer
NC1 - COM1: Öffner
- Verbraucher 2 (an Relais 2 / Kanal 2):
NO2 - COM2: Schließer
NC2 - COM2: Öffner
•Schließen Sie bei Bedarf die externen Taster
wie folgt an (Bild 3):
- Taster 1 (für Relais 1/Verbraucher 1):CH1
- Taster 2 (für Relais 2/Verbraucher 2):CH2
Hinweis: (nur RCL04) Führen Sie alle
Anschlusskabel durch die Öffnung an der
Unterseite über die wasserdichte PG-
Verschraubung in das Gerät ein.
•Setzen Sie den Gehäusedeckel wieder auf.
GB
Operating nstructions
Safety Advice
Carefully read through these instruc-
tions before connecting and operating
the mini receiver!
Caution! Observe the permissible supply
voltage and the max. contact rating!
Have faulty mini receivers checked by the manu-
facturer!
Do not make any unauthorized alterations or
modifications to the mini receiver!
Intended Use
The unit may only be operated with safety extra low
voltage (SELV) and may only be used as a radio
control for switching devices with safety extra low
voltage (SELV).
The manufacturer shall not be liable for any
damage caused by improper or non-intended use.
Function
The RCL03/RCL04 Mini Receiver can be operated
in a voltage range of 12-24 V AC/DC.
1 or 2 potential-free relay outputs may be switched
via separate radio channels, depending on model.
Three operating modes are available: Pulse
(1 second), ON/OFF (one-button-mode) and Dead
Man’s Mode.
For each channel 10 different radio transmitter
codes can be memorized.
It is also possible to connect one external pulse
button for each channel which can be used to
switch the corresponding relay according to the
selected operating mode.
Scope of Delivery
- Mini Receiver
- Mounting accessories(RCL03:adhesive pad
RCL04: screws, mollies)
- Operating instructions
Using the Mini receiver
Mounting and Connecting
•Remove the housing cover.
•Using the mounting accessories supplied,
mount the mini receiver in a suitable location.
•Selecting operating mode:
Caution! Switch off the supply voltage before
changing the operating mode. Switch it back
on afterwards!
Select the desired operating mode via jumper
J1 (Fig.: 1):
J1 in position 1-2: Pulse (1 second)
J1 in position 2-3: ON/OFF
J1 in position 3-4: Dead man’s mode (relay is
triggered as long as the transmitter button or
the external push button is pressed.)
•Connect the supply voltage (12-24 V AC/DC)
and the safety extra low voltage devices to be
switched as follows (Fig.: 2):
- Supply voltage: IN1, IN2
- Device 1 (relay 1 / channel 1):
NO1 - COM1: NO contact
NC1 - COM1: NC contact
- Device 2 (relay 2 / channel 2):
NO2 - COM2: NO contact
NC2 - COM2: NC contact
•If necessary, connect the external push button
as follows (Fig.: 3):
- Push button 1 (for relay 1/device 1):CH1
- Push button 2 (for relay 2/device 2):CH2
Note: (only RCL04) All cables are to be fed into
the Mini Receiver via the opening on the bottom
using the watertight PG screw fitting.
•Remount the housing cover.
2
3
1
72341 0905 D/GB
Montagehinweise:
Bringen Sie den Mini-Empfänger nicht in Bodennä-
he und nicht in Metallnähe an!
Alle Anschlussleitungen dürfen maximal 3 m lang
sein!
Wenden Sie sich bei Störungen an den Fachbetrieb
oder Hersteller.
Mounting advice:
Do not mount the Mini Receiver near the floor or
near large metal objects!
The maximum length of any connecting cables may
not exceed 3 m.
In the case of malfunctions, contact your retailer or
the manufacturer.
Kundendienst Customer Service
Sollten trotz sachgerechter Handhabung Störun-
gen auftreten oder wurde das Gerät beschädigt,
wenden Sie sich bitte an folgende Adresse:
If, despite correct handling, faults or malfunctions
occur or if the product was damaged, please
contact the company at the address below:
ELDAT GmbH
Im Gewerbepark 14
15711 Zeesen
Deutschland Germany
Telefon Phone: + 49 (0) 33 75 / 90 37-310
Telefax Telefax: + 49 (0) 33 75 / 90 37-90
Internet Internet: www.eldat.de
E-Mail E-mail: info@eldat.de
Sendercodes speichern
Für jeden Kanal können 10 unterschiedliche Sen-
dercodes gespeichert werden.
•Drücken Sie die Taste TA1 (für den Kanal 1)
bzw. TA2 (für den Kanal 2) und halten Sie
diese gedrückt. Nach ca. 3 s beginnt die LED
für ca. 10 s zu blinken. Lassen Sie die Taste
los.
•Drücken Sie innerhalb der 10 s kurz die
Sendertaste, deren Code gespeichert werden
soll. Wurde der Code gespeichert, leuchtet die
LED des Mini-Empfängers, solange die Sender-
taste gedrückt wird.
•Wiederholen Sie die beiden Schritte mit
weiteren Sendern.
Hinweis: Wenn alle Speicherplätze belegt sind,
blinkt die LED für ca. 4 s schnell.
Reset (Speicher komplett löschen)
Hinweis: Sie müssen den Speicherinhalt für jeden
Kanal separat löschen.
•Drücken Sie die Taste TA1 (für den Kanal 1)
bzw. TA2 (für den Kanal 2) und halten Sie
diese für 10 s gedrückt. Nach ca. 3 s beginnt
die LED zu blinken.
Wenn alle gespeicherten Sendercodes für den
gewählten Kanal gelöscht sind, leuchtet die
LED. Lassen Sie die Taste los.
Allgemeine Informationen
Entsorgungshinweise
Entsorgen Sie das Altgerät über eine Sammelstelle
für Elektronikschrott oder über Ihren Fachhändler.
Entsorgen Sie das Verpackungsmaterial in die
Sammelbehälter für Pappe, Papier und Kunststoffe.
Altgeräte dürfen nicht mit dem Hausmüll ent-
sorgt werden!
Gewährleistung
Innerhalb der gesetzlichen Garantiezeit beseitigen
wir unentgeltlich Mängel des Gerätes, die auf
Material- oder Herstellungsfehler beruhen, durch
Reparatur oder Umtausch.
Die Garantie erlischt bei Fremdeingriff.
Konformität
Dieses Produkt erfüllt die wesentlichen
Anforderungen der R&TTE-Richtlinie
1999/5/EG.
Die Konformitätserklärung ist auf folgender Inter-
netseite abrufbar: www.eldat.de.
Technische Daten
Frequenz: 433,92 MHz
/
868,30 MHz*
Modulation: ASK
Funktelegramm: 48-bit
Versorgungsspannung: 12-24 V AC/DC
Kontaktbelastung
externe Taster: ca. 5 mA
Stromaufnahme bei 24 V DC:
- bei Senderbetätigung 1-Kanal: ca. 35 mA,
2-Kanal: ca. 50 mA
- bei Tasterbetätigung 1-Kanal: ca. 40 mA,
2-Kanal: ca. 60 mA
Schutzart: IP20 oder IP65*
Ausgang: 1 oder 2 potenzialfreie
Relaiskontakte*
Max. Kontaktbelastung:
AC: 24 V / 1 A / 24 VA
DC: 30 V / 1 A / 30 W
Betriebstemperatur: -20°C bis +60°C
Abmessungen: RCL03: 63 x 35 x 70 mm
RCL04: 114 x 72 x 36 mm
Gewicht: RCL03: ca. 50 g
RCL04: ca. 100 g
* je nach Ausführung
Memorizing the Transmission Codes
10 different transmission codes can be memorized
for each channel.
•Press and hold button TA1 (for channel 1) or
TA2 (for channel 2). After about 3 s the LED will
begin to flash for about 10 s. Release the
button.
•Within 10 s, press the transmitter button of
which the code is to be memorized. As soon as
the code is memorized, the LED of the mini re-
ceiver remains lit for as long as the transmitter
button is held.
•Repeat both steps with other transmitters.
Note: If all memory locations are occupied, the
LED flashes rapidly for approx. 4 s.
Reset (Deleting Memory completely)
Note: The memory for each channel must be
deleted separately.
•Press and hold button TA1 (for channel 1) or
TA2 (for channel 2) for 10 s. After about 3 s the
LED will begin to flash.
As soon as all memorized transmission codes
for the chosen channel have been deleted, the
LED will light up. Release the button.
General Information
Disposal
Dispose of the waste product via a collection point
for electronic scrap or via your specialist dealer.
Put the packaging material into recycling bins for
cardboard, paper and plastics.
Waste electrical products may not be disposed
of with household waste!
Warranty
Within the statutory warranty period we undertake
to rectify free of charge by repair or replacement
any product defects arising from material or produc-
tion faults.
Any unauthorized tampering with, or modifications
to the product shall render this warranty null and
void.
Conformity
This product conforms to the basic
requirements of the R&TTE Directive
1999/5/EC.
The Declaration of Conformity can be found on the
Internet at: www.eldat.de.
Technical Details
Frequency: 433.92 MHz or
868.30 MHz*
Modulation: ASK
Radio telegram: 48 bit
Supply voltage: 12-24 V AC/DC
Max. contact rating
external push-buttons: approx. 5 mA
Transmitting current consumption at 24 V DC:
- Transmitter operation 1-channel: approx. 35 mA
2-channel: approx. 50 mA
- Push-button operation 1-channel: approx. 40 mA
2-channel: approx. 60 mA
Degree of protection: IP20 or IP65*
Output: 1 or 2 potential-free relay
contacts*
Max. contact rating: AC: 24 V / 1 A / 24 VA
DC: 30 V / 1 A / 30 W
Operating temperature: -20°C to +60°C
Dimensions: RCL03: 63 x 35 x 70 mm
RCL04: 114 x 72 x 36 mm
Weight: RCL03: approx. 50 g
RCL04: approx. 100 g
* depending on model

This manual suits for next models

9

Other Eldat Receiver manuals

Eldat Easywave RCR02E5002A01 User manual

Eldat

Eldat Easywave RCR02E5002A01 User manual

Eldat EASY WAVE RCL03 User manual

Eldat

Eldat EASY WAVE RCL03 User manual

Eldat RCU01 Series User manual

Eldat

Eldat RCU01 Series User manual

Eldat EasyWave RCL07 User manual

Eldat

Eldat EasyWave RCL07 User manual

Eldat RCL07 User manual

Eldat

Eldat RCL07 User manual

Eldat RCJ01 Series User manual

Eldat

Eldat RCJ01 Series User manual

Eldat RCL03 Series User manual

Eldat

Eldat RCL03 Series User manual

Eldat RCU01-4104M-01 User manual

Eldat

Eldat RCU01-4104M-01 User manual

Eldat Easywave RCL07 User manual

Eldat

Eldat Easywave RCL07 User manual

Eldat RCJ31 User manual

Eldat

Eldat RCJ31 User manual

Eldat Easywave neo RCJ35 User manual

Eldat

Eldat Easywave neo RCJ35 User manual

Eldat RCU08 User manual

Eldat

Eldat RCU08 User manual

Eldat Easywave RCL07 User manual

Eldat

Eldat Easywave RCL07 User manual

Eldat Easywave neo User manual

Eldat

Eldat Easywave neo User manual

Eldat Easywave neo RCJ32 User manual

Eldat

Eldat Easywave neo RCJ32 User manual

Popular Receiver manuals by other brands

Multitone RPR750 Series manual

Multitone

Multitone RPR750 Series manual

Pioneer MVH-X375 owner's manual

Pioneer

Pioneer MVH-X375 owner's manual

Pico Macom PFR-2 owner's manual

Pico Macom

Pico Macom PFR-2 owner's manual

Harman Kardon AVR 147 owner's manual

Harman Kardon

Harman Kardon AVR 147 owner's manual

RCA RT2300 user manual

RCA

RCA RT2300 user manual

FMA Tetra owner's manual

FMA

FMA Tetra owner's manual

AOR SR2200 operating manual

AOR

AOR SR2200 operating manual

GBD DRS4335 Instructions for installations

GBD

GBD DRS4335 Instructions for installations

Ten-Tec RX-400A user manual

Ten-Tec

Ten-Tec RX-400A user manual

Nyrius TB72 quick start guide

Nyrius

Nyrius TB72 quick start guide

Zte ZXSDR RSUC user manual

Zte

Zte ZXSDR RSUC user manual

Yamaha RX-V340 Service manual

Yamaha

Yamaha RX-V340 Service manual

Lumistar LS-28-DRSM Quick start manual

Lumistar

Lumistar LS-28-DRSM Quick start manual

Hyundai AH-3110 manual

Hyundai

Hyundai AH-3110 manual

Pioneer Elite SC-72 operating instructions

Pioneer

Pioneer Elite SC-72 operating instructions

Harman Kardon AVR 1650 Service manual

Harman Kardon

Harman Kardon AVR 1650 Service manual

CYP CH-106TXN Operation manual

CYP

CYP CH-106TXN Operation manual

Denon AVR-4520CI owner's manual

Denon

Denon AVR-4520CI owner's manual

manuals.online logo
manuals.online logoBrands
  • About & Mission
  • Contact us
  • Privacy Policy
  • Terms and Conditions

Copyright 2025 Manuals.Online. All Rights Reserved.