Eldes ESIM110 User manual

ESIM110
ESIM120
GSM SWITCHGATE CONTROLLER

2
2
EN ESIM110/ESIM120 Manual v.3.3
User Manual v3.3
Valid for ESIM110/ESIM120 v11.05.00 and up
SAFETY INSTRUCTIONS
Please read and follow these safety guidelines to safeguard yourself and others:
• GSM switch-gate controller ESIM110/ESIM120 (later referred to as “the system” or “ the device”) contains a built-in radio transceiver
operating in GSM 850/900/1800/1900 MHz bands.
• DO NOT use the system where it can cause potential danger and interfere with other devices – such as medical devices.
• DO NOT use the system in hazardous environment.
• DO NOT expose the system to high humidity, chemical environment or mechanical impact.
• DO NOT attempt to repair the system yourself – any repairs must be carried out by fully qualied personnel only.
Disconnect the mains power before installing. Never install or carry out maintenance during stormy weather. The electric sock-
et that powers the system must be easily accessible.
Please use the 10-24V 50Hz ~200mA AC or 10-24V 200mA DC power supply unit that meets the EN 60950-1 standard.
Any additional device you connect to the system, such as a computer, must also be powered by an EN 60950-1 approved
supply. When connecting the power supply to the system, switching the polarity terminal places does not have any aect.
External power supply can be connected to AC mains only inside installation room
with automatic 2-pole circuit breaker capable of disconnecting circuit in the event
of short circuit or over-current condition. Open circuit breaker must have a gap
between connections of more than 3mm and the disconnection current 5A.
Phase
AC 230V
50 Hz/DC 24V
USB cable
Null
PE
ESIM110/
ESIM120
AC/DC
To switch the system o, unplug the external electric power supply from or any other linked device that the system is
powered from
A blown fuse cannot be replaced by the user. The replacement fuse has to be of the kind indicated by the manufacturer (fuse
F1 model – MINISMDC050F 0.5A).
If you use a computer for the device conguration, it must be earthed.
The WEEE (Waste Electrical and Electronic Equipment) symbol on this product (see left) means it must not be disposed of in
household waste. To prevent possible harm to human health and/or the environment, you must dispose of this product in an
approved and environmentally safe recycling facility. For further information contact your system supplier, or your local waste
authority.

3
3
EN
ESIM110/ESIM120 Manual v.3.3
CONTENTS
1. GENERAL INFORMATION ...........................................................................................................................................................6
2. TECHNICAL SPECIFICATIONS ....................................................................................................................................................6
2.1. Electrical & Mechanical Characteristics.........................................................................................................................................................6
2.2. Main Unit, LED Indicator & Connector Functionality...................................................................................................................................7
2.3. Wiring Diagrams ................................................................................................................................................................................................8
3. INSTALLATION ...........................................................................................................................................................................9
4. GENERAL OPERATION .............................................................................................................................................................10
5. CONFIGURATION METHODS ....................................................................................................................................................10
5.1. SMS Text Messages.........................................................................................................................................................................................10
5.2. ELDES Conguration Tool ..............................................................................................................................................................................10
5.3. Remote Conguration via Web Browser......................................................................................................................................................10
5.3.1. Establishing Remote Connection .................................................................................................................................................................13
6. SYSTEM LANGUAGE.................................................................................................................................................................14
7. SMS PASSWORD.......................................................................................................................................................................15
8. ADMINISTRATOR PHONE NUMBERS.......................................................................................................................................15
9. DATE AND TIME........................................................................................................................................................................17
9.1. Automatic Date and Time Synchronization ................................................................................................................................................17
10. USER PHONE NUMBER DATABASE.........................................................................................................................................18
10.1. User Validity and Access Restriction ...........................................................................................................................................................21
11. OUTPUT (-S)............................................................................................................................................................................23
11.1. Output Name (-s).............................................................................................................................................................................................23
11.2. Output Control by Free of Charge Phone Call ............................................................................................................................................ 24
11.3. Output Control by SMS Text Message..........................................................................................................................................................25
11.4. Output Control Conrmation by Call Back .................................................................................................................................................. 28
11.5. Output Control from any Phone Number.................................................................................................................................................... 29
11.6. Automatic Output Control............................................................................................................................................................................. 30
12. SCHEDULERS ..........................................................................................................................................................................31
13. EVENT LOG ..............................................................................................................................................................................33
14. INPUTS....................................................................................................................................................................................35
14.1. Input Names and Alarm Notications..........................................................................................................................................................35
14.2. Disabling and Enabling Inputs.......................................................................................................................................................................37
15. SYSTEM INFORMATION. INFO SMS........................................................................................................................................ 38
15.1. Periodic Info SMS............................................................................................................................................................................................ 39
16. SYSTEM NOTIFICATIONS ....................................................................................................................................................... 40
16.1. SMSC (Short Message Service Center) Phone Number............................................................................................................................ 40
17. GPRS NETWORK SETTINGS ....................................................................................................................................................41
18. REMOTE SYSTEM RESTART................................................................................................................................................... 43
19. TECHNICAL SUPPORT............................................................................................................................................................ 44
19.1. Troubleshooting ............................................................................................................................................................................................. 44
19.2. Restoring Default Parameters ..................................................................................................................................................................... 44
19.3. Updating the Firmware via USB Cable........................................................................................................................................................ 45
20. SMART GATE.......................................................................................................................................................................... 46
21. RELATED PRODUCTS ............................................................................................................................................................. 47

4
4
EN ESIM110/ESIM120 Manual v.3.3

5
5
EN
ESIM110/ESIM120 Manual v.3.3
Limited Liability
The buyer agrees that the system will reduce the risk of re, theft, burglary or other danger but that it does not guarantee against the oc-
currence of such events. “ELDES UAB” will not take any responsibility for the loss of personal eects, property or revenue whilst using the
system. The liability of “ELDES UAB” is limited to the value of the system purchased. “ELDES UAB” is not aliated with any mobile/wireless/
cellular provider and is therefore not responsible for the quality of such services.
Manufacturer Warranty
The system carries a 24-month manufacturer warranty from “ELDES UAB”. The warranty begins the day the system is purchased by the
user and the receipt must be retained as proof of purchase date. The warranty remains valid only if the system is used as intended, fol-
lowing all guidelines outlined in this manual and in accordance with the operating conditions specied. The warranty is void if the system
has been exposed to mechanical impact, chemicals, high humidity, uids, corrosive and hazardous environments or force majeure factors.
Dear Customer,
Thank you for choosing to purchase the GSM switch-gate controller ESIM110/ESIM120. Your thoughtful decision will ensure reliable
solution for many years as all ELDES products are manufactured to meet the highest standards.
We are condent that you will be completely satised with your product. However, in the unlikely event that you do experience a
problem, please contact the dealer from whom you made your purchase.
UAB ELDES
www.eldes.lt
Contents of Pack
Item Quantity
1. ESIM110/ESIM120 .................................1
2. User manual............................................1
3. GSM antenna. ......................................... 1
Copyright © “ELDES UAB”, 2014. All rights reserved
It is strictly forbidden to copy and distribute information in this document or pass to a third party without an advanced
written authorization from “ELDES UAB”. “ELDES UAB” reserves the right to update or modify this document and/or relat-
ed products without a warning. Hereby, “ELDES UAB” declares that the GSM switch-gate controller ESIM110/ESIM120 is
in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC. The declaration of
conformity may be consulted at www.eldes.lt.

6
6
EN ESIM110/ESIM120 Manual v.3.3
1. GENERAL INFORMATION
ESIM110/ESIM120 is a micro-controller based device intended to provide access control for gate automatics, road barriers or to remotely
turn ON/OFF any electrical appliance via the GSM network.
Examples of using the system:
• Access control.
• Parking lot control of residential houses or oces.
• Gate control of private houses.
• Any electrical appliance control: lighting, watering, heating etc.
• Remote reboot of the “frozen” systems, such as computer network or a server.
Main features
• Manual output control by free of charge phone call.
• Automatic output control in accordance with the scheduled time.
• Congurable output pulse duration.
• Automatic date and time synchronization.
• Up to 5 administrators for system conguration by SMS text messages, acceptance of input alarm SMS text messages, output control
by SMS text message and free of charge phone call.
• User database capacity – up to 500 (1000 or 2000 – optional) users for output control by free of charge phone call.
• User phone number validity limitation in accordance with a set deadline (date/time) or number of rings to the system.
• Output control restriction for users in accordance with the specied weekdays and time.
• Event log of 1000 events containing date and time as well as administrator/user phone number and user name who controlled the
output.
• 3 inputs with customizable alarm texts for notication on gate state or in case it gets jammed.
• Periodic self-test notication by SMS text message to administrator phone number.
2.TECHNICAL SPECIFICATIONS
2.1. Electrical & Mechanical Characteristics
Supply voltage 10-24V 50Hz ~ 200mA max / 10-24V 200mA max
Current used in standby mode up to 50mA
GSM modem frequency 850/900/1800/1900 MHz
Number of outputs 1 (ESIM110); 2 (ESIM120)
Output type Relay; NO (normally-open) or NC (normally-closed) - congurable
Maximum commuting output values 24V 50Hz ~ 0,5A / 24V 1A
Number of “low” level (negative) inputs 2
Number of “high” level (positive) inputs 1
“Low” level (negative) input value range 0... 16V -0.8... -0.4mA
“High” level (positive) input value range 5... 50V 0.17 .... 1.7mA
“Low” level (negative) and “high” level
(positive) input connection type
NO (normally-open)
Dimensions 63x82x17 mm
Operating temperature range -20…+55oC (-30...+55oC with limitations)
Humidity 0-90% RH @ 0... +40 °C (non-condensing)

7
7
EN
ESIM110/ESIM120 Manual v.3.3
2.2. Main Unit, LED Indicator & Connector Functionality
ANT
MIC
AC/DC RELAY COM
ESIM110 ESIM120
DEF
Z5 Z4 Z3 Z2 Z1 AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1
USB
F1
ANT
MIC
USB
F1
SIM CARD
SIM CARD
G S M
MO DE M
G S M
MO DE M
SIM STAT
NETW
SIM STAT
NETW
DEF
Main Unit Functionality
ANT GSM antenna SMA type connector
USB Mini USB port
SIM CARD SIM card slot / holder
GSM MODEM GSM network 850/900/1800/1900 MHz modem
MIC N/A
SIM STAT Red light-emitting diode indicating SIM card status
NETW Green light-emitting diode indicating GSM signal strength
DEF Pins for restoring default settings
F1 0.5A fuse
Connector Functionality
AC/DC Power supply terminals
RELAY ESIM110 output C1 terminal
RELAY1 ESIM120 output C1 terminal
RELAY2 ESIM120 output C2 terminal
COM Common terminal
Z5 N/A
Z4 N/A
Z3 “Low” level (negative) input terminal
Z2 “High” level (positive) input terminal
Z1 “Low” level (negative) input terminal
1

8
8
EN ESIM110/ESIM120 Manual v.3.3
LED Indicator Functionality
SIM STAT indication SIM card status
OFF SIM card is not yet connected to the GSM network / SIM card is not present / PIN code enabled
Steady ON SIM card is operating successfully
Flashing GSM connection failed
NETW indication GSM signal strength
OFF No GSM signal
Flashing every 1 sec. Poor
Flashing several times per sec. Medium
Steady ON Excellent
2.3. Wiring Diagrams
General wiring
ESIM 110/ESIM120
AC/DC
Power
supply
GATE AUTOMATION DEVICE
+
-
RELAY COM Z3 Z2 Z1
Example of ESIM120 system wiring to gate automation device
ESIM120 GATE AUTOMATION DEVICE
AC/DC RELAY1 RELAY2 COM Z5 Z4 Z3 Z2 Z1 F0 +24v
FO= Fault output; open collector type
+24V = Power supply output for
powering aux. equipment
= Pulse input
GND = Common terminal
GND
3
2

9
9
EN
ESIM110/ESIM120 Manual v.3.3
3.INSTALLATION
• The system should be installed indoors, in stationary environment ONLY.
• For the connection of input/output terminals, use 0.50 mm21 thread unshielded cable of up to 100 meters length.
1. Wire up the system in accordance with the wiring diagrams (see 2.3 Wiring Diagrams for more details).
2. Connect the GSM antenna. Based on the type of the GSM antenna supplied with ESIM110/ESIM120 unit, follow the recommendations
for the antenna installation:
GSM/GPRS
antenna
4
Never install in the following
locations:
• inside the metal cabinet
• close to the metal surface
and/ or power lines
3. Disable the PIN code request of the SIM card by inserting it into a mobile phone and following the proper menu steps.
4. Once the PIN code is disabled, insert the SIM card into the SIM card slot / holder of ESIM110/ESIM120 system.
5
6
5. Power up the system and wait until indicator SIM STAT lights up indicating SIM card status.
6. Once the indicator SIM STAT lights OFF, the illuminated indicator NETW lights up indicating that the system has successfully connected
to the GSM network. To nd the strongest GSM signal, position the GSM antenna and follow the indications provided by NETW indicator
(see 2.2. Main Unit, LED Indicator & Connector Functionality for more details).
7. Change the system language if necessary (see 6. SYSTEM LANGUAGE for more details).
8. Change the default SMS password (see 7. SMS PASSWORD for more details).
9. Set the phone number for Admin 1 (see 8. ADMINISTRATOR PHONE NUMBERS for more details).
10. Set system date and time (see 9. DATE AND TIME for more details).
11. Once the system is fully congured, it is ready for use. However, if you fail to receive a reply by SMS text message from the system,
please check the SMSC (Short Message Service Center) phone number. For more details regarding the SMS center phone number,
please refer to 17. SMSC (Short Message Service Center) Phone Number.
ATTENTION: The system is NOT compatible with pure 3G SIM cards. Only 2G/GSM SIM cards and 3G SIM cards with 2G/GSM prole
enabled are supported. For more details, please contact your GSM operator.
ATTENTION: We also recommend you to disable call forwarding, voice mail/text message reports on missed/busy calls and
similar services that might cause incorrect system operation. Please contact your GSM operator for more details on these services and
how to disable them.
NOTE: For maximum system reliability we recommend you do NOT use a Pay As You Go SIM card. Otherwise, in the event of insucient
credit balance on the SIM card, the system would fail to make a phone call or send SMS text messages.
NOTE: We advise you to choose the same GSM SIM provider for your system as for your mobile phone. This will ensure the fastest,
most reliable SMS text message delivery service and phone call connection.
NOTE: Even though the installation process of ESIM110/ESIM120 is not too complicated, we still recommend to perform it by a person
with basic knowledge in electrical engineering and electronics to avoid any system damage.

10
10
EN ESIM110/ESIM120 Manual v.3.3
4.GENERAL OPERATION
When a phone call is made to the phone number of the SIM card inserted in ESIM110/ESIM120, the system will verify if the caller’s phone
number exists in the memory. If the caller is one of the 5 administrators or the phone number belongs to one of the 500 database users, the
system will reject the phone call, thus making the phone call free of charge, and open the gate. By ringing to ESIM110/ESIM120 again, it will
close the gate. If the phone number is not recognized, the system will reject the phone call and ignore it. The GSM switch-gate controller
can also control your gate automatically in accordance with the scheduled time or by sending an SMS text message from the administrator’s
phone number.
By connecting a sensor to one of the 3 inputs, the administrators can receive SMS text messages regarding the gates that failed to close
during the set time period.
User/Admin
ESIM110/ESIM120
CALL
7
5.CONFIGURATION METHODS
5.1. SMS Text Messages
!!! In this installation manual the underscore character ”_” represents one space character. Every underscore character
must be replaced by a single space character. There must be no spaces or other unnecessary characters at the beginning
and at the end of the SMS text message.
SMS
In order to congure and control the system by SMS text message, send the text command to the ESIM110/ESIM120 system
phone number from one of the preset administrator phone numbers. The structure of SMS text message consists of 4-digit
SMS password (the default SMS password is 0000 – four zeros), the parameter and value. For some parameters the value does
not apply e. g. STATUS. The variables are indicated in lower-case letters, while a valid parameter value range is indicated in
brackets.
5.2. ELDES Conguration Tool
Cong
Tool
Software ELDES Conguration Tool is intended for ESIM110/ESIM120 GSM switch-gate controller conguration via USB port
locally. This software simplies system conguration process by allowing to use a personal computer in the process. Before
starting to use ELDES Conguration Tool software, please read the user guide provided in the software’s HELP section.
ELDES Conguration Tool is freeware and can be downloaded from at: www.eldes.lt
NOTE: ELDES Conguration Tool software is secured with SMS password. The default SMS password is 0000 (see 7. SMS PASS-
WORD).
5.3. Remote Conguration via Web Browser
WEB
BROWSER
The system comes equipped with a remote conguration feature allowing to congure the parameters via any available web
browser. Before remotely connecting to ESIM110/ESIM120 via GPRS connection, ensure that:
• SIM card is inserted into the SIM CARD slot (see 2.2. Main Unit, LED & Connector Functionality).
• Mobile internet service (GPRS) is enabled on the SIM card.
• ESIM110/ESIM120 is powered up.
• Default SMS password is changed to a new 4-digit password (see 7. SMS PASSWORD).
• Admin 1 phone number is set up (see 8. ADMINISTRATOR PHONE NUMBERS).
• APN, user name and password are set up (see 17. GPRS NETWORK SETTINGS).

11
11
EN
ESIM110/ESIM120 Manual v.3.3
The system supports the following remote connection modes:
• CLIENT – The device connects to the conguration server making the device accessible through a web browser when the administrator
logs in via ELDES website (see 5.3.1. Establishing Remote Connection). This mode is set by default and DOES NOT require the static
IP address for the device SIM card. Default Client mode parameters are as follows:
• Server IP – cong.eldes.lt
• DNS1 – 84.32.3.34
• DNS1 – 84.32.134.1
• Port – 5555
• SERVER – The device is accessible directly through a web browser using the device IP address and local port number (see
5.3.1.Establishing Remote Connection). A static IP address, provided by GSM operator, is required for the device SIM card. This mode
is for advanced use only. Default Server mode parameters are as follows:
• Local Port – 5000
• Protocol – TCP
Set remote
connection mode
as Server
SMS
SMS text message content:
ssss_SETGPRS:TYPE:SERVER
Value: ssss – 4-digit new SMS password.
Example: 1111_SETGPRS:TYPE:SERVER
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set local port SMS
SMS text message content:
ssss_SETGPRS:LPORT:lpprt
Value: ssss – 4-digit new SMS password; lpprt – local port number, range – [1... 65535].
Example: 1111_SETGPRS:LPORT:5000
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set protocol SMS
SMS text message content:
sssss_SETGPRS:PROTOCOL:ptc
Value: ssss – 4-digit SMS password; ptc – protocol, range – [TCP... UDP].
Example: 1111_SETGPRS:PROTOCOL:UDP
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

12
12
EN ESIM110/ESIM120 Manual v.3.3
Set remote
connection mode as
Client
SMS
SMS text message content:
ssss_SETGPRS:TYPE:CLIENT
Value: ssss – 4-digit new SMS password.
Example: 1111_SETGPRS:TYPE:CLIENT
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set server IP address SMS
SMS text message content:
ssss_SETGPRS:IP:add.add.add.add
Value: ssss – 4-digit SMS password; add.add.add.add – server IP address.
Example: 1111_SETGPRS:IP:65.82.119.5
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set server port SMS
SMS text message content:
ssss_SETGPRS:PORT:pprrt
Value: ssss – 4-digit SMS password; pprrt – server port number, range – [1... 65535].
Example: 1111_SETGPRS:PORT:5521
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set DNS1 server IP
address
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Set DNS2 server IP
address
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

13
13
EN
ESIM110/ESIM120 Manual v.3.3
View remote
conguration
parameters
SMS
SMS text message content:
ssss_SETGPRS?
Value: ssss – 4-digit SMS password.
Example: 1111_SETGPRS?
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
5.3.1.Establishing Remote Connection
1. In order to activate a remote connection, please send the following SMS text message from user phone number. Upon the successful
SMS text message delivery, the system establishes a connection session for 20 minutes. An SMS reply, containing temporal user name
and password, will be sent shortly.
Establish remote
connection SMS
SMS text message content:
ssss_CONNECT:PROFILE1
Value: ssss – 4-digit new SMS password.
Example: 1111_CONNECT:PROFILE1
To set a dierent session duration or connect for a custom session duration, please refer to the following conguration methods.
Set session duration Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Establish remote
connection for custom
session duration
SMS
SMS text message content:
ssss_CONNECT:TIMEOUT:ses-d
Value: ssss – 4-digit new SMS password; ses-d – session duration, range – [0... 14400] mi-
nutes.
Example: 1111_CONNECT:TIMEOUT:120
Alternatively, the system supports remote connection establishment by making a phone call from the administrator phone number to
the system. Once the call is received, the system rejects the call thus making it free of charge and replies with the login details by SMS
text message to the administrator phone number. By default, this feature is disabled. To enable/disable it, please refer to the following
conguration methods.
Enable/disable
remote connection
establishment by
phone call
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

14
14
EN ESIM110/ESIM120 Manual v.3.3
NOTE: 0 value sets unlimited session duration.
NOTE: ELDES Conguration Tool software and remote conguration web interface allows to set the unlimited session duration value.
NOTE: Once the remote connection establishment by phone call is enabled, the specied administrator will no longer be able to
control the output via free of charge phone call.
2. a) If running in Client mode, open a web browser and type in http://www.eldes.lt/login.
b) If running in Server mode, open a web browser and type in http://deviceIPaddress:localport
3. Enter the received login details and press Login button.
4. After the system conguration is complete, use one of the following methods to end the conguration process:
• Wait for the session timeout and the system to reply with an SMS text message conrming the end of the session.
• Shut down the connection with the conguration server at any time by sending an SMS text message.
Shut down the
connection with
conguration server
SMS
SMS text message content:
ssss_STOP
Value: ssss – 4-digit new SMS password.
Example: 1111_STOP
ATTENTION: Output control is disabled during the remote conguration process.
6.SYSTEM LANGUAGE
The system comes equipped with a multiple languages for communication with the administrator by SMS text messages. The default
system language depends on the rmware, which is based on the customer’s location.
List of currently available system languages:
• English
• Estonian
• German
• Lithuanian
• French
• Slovak
Set system language SMS
SMS text message content:
LN
Value: LN – language index; range – [EN – English, EE – Estonian, DE – German, LT – Lithua-
nian, FR – French, SK – Slovak].
Example: LT
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
NOTE: To change the language once the system has already been congured, you need to reset the device to the default congura-
tion. For more details on how to do this, please refer to 19.2. Restoring Default Parameters.

15
15
EN
ESIM110/ESIM120 Manual v.3.3
7.SMS PASSWORD
For security reasons, the system uses the following type of password:
• SMS password – 4-digit password used for system conguration and control from administrator phone number by SMS text
messages and logging in to ELDES Conguration Tool software . By default, SMS password is 0000, which MUST be changed!
Set SMS password SMS
SMS text message content:
wwww_PSW_ssss
Value: wwww – 4-digit default SMS password; ssss – 4-digit new SMS password; range –
[0001... 9999].
Example: 0000_PSW_1111
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
NOTE: The system rejects the SMS text messages containing wrong SMS password even from a preset administrator phone number.
8.ADMINISTRATOR PHONE NUMBERS
The system supports up to 5 administrator phone numbers identied as Admin 1 through 5. When the phone number is set, the
administrator will be able to congure and control the system by SMS text messages as well as by free of charge phone call and receive the
input alarm SMS text messages from the system (see 14.1. Input Names and Alarm Notication). ESIM120 allows to assign output C1,
output C2 or both outputs (simultaneous control) to a certain administrator.
By default, the system ignores any incoming calls and SMS text messages from a non-preset phone number as well as it rejects the SMS
text messages containing wrong SMS password even from a preset administrator phone number. For more details on how to enable output
control from a non-preset phone number, please refer to 11.5. Output Control from any Phone Number.
To set Admin 1 phone number is mandatory, while the other 4 are optional. The supported phone number format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following format:
[international code][area code][local number], example for UK: 4417091111111.
Set administrator
phone number SMS
SMS text message content:
ssss_NRas:ttteeellnnuumm
Value: ssss – 4-digit SMS password; as – administrator phone number slot, range – [1... 5];
ttteeellnnuumm – up to 15 digits administrator phone number.
Example: 1111_NR1:4417091111111
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
View administrator
phone numbers SMS
SMS text message content:
ssss_HELPNR
Value: ssss – 4-digit SMS password.
Example: 1111_HELPNR
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

16
16
EN ESIM110/ESIM120 Manual v.3.3
Assign output
(-s) to individual
administrator
ONLY FOR ESIM120
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Delete administrator
phone number SMS
SMS text message content:
ssss_NRas:DEL
Value: ssss – 4-digit SMS password; as – administrator phone number slot, range – [2... 5].
Example: 1111_NR2:DEL
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
ATTENTION: NEVER set a phone number of the device’s SIM card as an administrator phone number!
ATTENTION: Once Admin 1 phone number is set, the system will restrict only to modify it
ATTENTION: Multiple administrator phone numbers can be set by a single SMS text message, Example: 1111_NR1:4417091111111_
NR5:4417091111112_NR2:4417091111113_NR3: 4417091111114
NOTE: Multiple administrator phone numbers can be deleted by a single SMS text message, Example: 1111_NR2:DEL_NR4:DEL_
NR3:DEL
NOTE FOR ESIM120: The administrator can control any output by SMS text message regardless of the output assigned to the admin-
istrator phone number (see 11.3. Output Control by SMS Text Message).
For more details on output control, please refer to 11. OUTPUT (-S).

17
17
EN
ESIM110/ESIM120 Manual v.3.3
9.DATE AND TIME
The system comes equipped with internal real-time clock (RTC) that keeps track of the current date and time. Once the system is up and
running, the user must set the correct date and time, otherwise the system will not operate properly. By default, after shutting down and
starting up the system, the date and time must be set again. In order to avoid manual date and time set up, please use the automatic date
and time synchronization feature (see 9.1. Automatic Date and Time Synchronization).
Set date and time SMS
SMS text message content:
ssss_yyyy.mm.dd_hr:mn
Value: ssss – 4-digit SMS password; yyyy – year; mm – month, range – [01... 12]; dd – day,
range – [01... 31]; hr – hours, range – [00... 23]; mn – minutes, range – [00... 59].
Example: 1111_2013.03.16_14:33
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
9.1. Automatic Date and Time Synchronization
This feature enables the system to set the date and time automatically without the user being involved in this process. The system supports
the following methods of automatic date and time synchronization that are used automatically on system start-up and periodically (by
default – every 30 days):
• Via GSM network – Once enabled, the system automatically sends a date/time request to the GSM operator. This method is the
most accurate synchronization method. Some GSM operators might not support it.
• By SMS text message – Once enabled, the system automatically sends the SMS text message to its own phone number and
retrieves the date and time from the SMS text message reply, as the included date and time is set by the SMSC (SMS center). This
method is not as accurate as the synchronization via GSM network, but always eective.
By default, synchronization via GSM network is disabled. To enable/disable automatic date and time synchronization via GSM network,
please refer to the following conguration methods.
Enable/disable
synchronization via
GSM network
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
By default, synchronization by SMS text message is disabled. To enable/disable automatic date and time synchronization by SMS text
message, please enter/remove device phone number using one of the following conguration methods.
Enter/remove device
phone number for
synchronization by
SMS text message
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

18
18
EN ESIM110/ESIM120 Manual v.3.3
By default, the date and time synchronization period is 30 days. To set a dierent period, please refer to the following conguration
methods.
Set synchronization
period
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
NOTE: When setting up automatic date and time synchronization feature remotely, you may wish to restart the system when done.
For more details, please refer to 18. REMOTE SYSTEM RESTART.
NOTE: 0 value disables periodic date and time synchronization.
NOTE: When both synchronization methods are enabled, the system will always attempt to synchronize date and time via GSM net-
work every time the system shuts down and starts up again and in accordance with the set period value. In the event of rst method’s
failure, the system will attempt to use the SMS text message method as a backup.
10. USER PHONE NUMBER DATABASE
The system comes equipped with a user database of 500 user capacity. When the phone number is set, the user will be able to control
the output (-s) by free of charge phone call. ESIM120 user database allows to assign output C1, output C2 or both outputs (simultaneous
control) to a certain user. The supported phone number format is the following:
• International (w/o plus) – The phone numbers must be entered starting with an international country code in the following
format: [international code][area code][local number], example for UK: 4417091111111.
ESIM110/ESIM120 user database supports user validity and access restriction features. For more details, please refer to 10.1. User
Validity and Access Restriction.
Optionally, a user name can be set that typically species the owner’s name of a certain phone number, for example: John.
The phone number and user name (if any) are used when searching for a certain user in the database as well as they are automatically
added in the event log after the successful output control event (see 13. EVENT LOG).
Add user phone
number (and user
name)
SMS
SMS text message content:
ssss_N:ttteeellnnuumm or ssss_N:ttteeellnnuumm:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_N:4417091111111:John
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

19
19
EN
ESIM110/ESIM120 Manual v.3.3
View user phone
numbers SMS
SMS text message content:
ssss_GETALLNUMBERS
Value: ssss – 4-digit SMS password.
Example: 1111_GETALLNUMBERS
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Search for user by
phone number or
name
SMS
SMS text message content:
ssss_T:ttteeellnnuumm or ssss_T:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_T:John
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Assign output (-s) to
individual user
ONLY FOR ESIM120
SMS
SMS text message content:
ssss_OUTPUT_ttteeellnnuumm_o or ssss_OUTPUT_user-name_o
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
o– output number; range [1 – output C1; 2 – output C2; 3 – both outputs]; user-name – up
to 16 characters user name.
Example: 1111_OUTPUT_4417091111111_2
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
Delete individual user SMS
SMS text message content:
ssss_D:ttteeellnnuumm or ssss_D:user-name
Value: ssss – 4-digit SMS password; ttteeellnnuumm – up to 15 digits user phone number;
user-name – up to 16 characters user name.
Example: 1111_GETALLNUMBERS
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.

20
20
EN ESIM110/ESIM120 Manual v.3.3
Delete all users SMS
SMS text message content:
ssss_D:ALL
Value: ssss – 4-digit SMS password.
Example: 1111_D:ALL
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
The user database can be exported/imported to/from a .csv le for backup purposes or for a convenient user database management. To
export/import an existing user database, please refer to the following conguration method.
Export/import
existing user database
from/to le
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
By default, the user database is enabled and output control by all database users is permitted. To deny output control instead of deleting
all users from the database, please disable the user database using one of the following conguration methods.
Disable user database SMS
SMS text message content:
ssss_DBM_OFF
Value: ssss – 4-digit SMS password.
Example: 1111_DBM_OFF
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
To enable user database, please refer to the following conguration methods.
Enable user database SMS
SMS text message content:
ssss_DBM_ON
Value: ssss – 4-digit SMS password.
Example: 1111_DBM_ON
Cong
Tool This operation may be carried out from the PC using the ELDES Conguration Tool software.
WEB
BROWSER This operation may be remotely carried out from the PC using the web browser.
ATTENTION: Space and colon characters are NOT allowed in the user names.
NOTE: Multiple users can be added by a single SMS text message, Example: 1111_N:4417091111111:John_ 4417091111112:_
4417091111113:Tom
NOTE: Multiple users can be deleted by a single SMS text message, Example: 1111_D:John_ 4417091111113_Mark
For more details on output control, please refer to 11. OUTPUT (-S).