ElectrIQ P12CE-V2 User manual

USER MANUAL
12,000 BTU PORTABLE AIR CONDITIONER
Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and
keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals
P12CE-V2

Page 2 of 15
CONTENTS
SAFETY INSTRUCTIONS
3
FEATURES
5
DIAGRAM AND ACCESSORIES
6
INSTALLATION
7
OPERATION
9
REMOTE CONTROL
11
WATER-DRAINAGE
11
MAINTENANCE
12
TROUBLESHOOTING
13
TECHNICAL DATA
14
SUPPORT
15

Page 3 of 15
SAFETY INSTRUCTIONS
Important!
Carefully read the instructions before operating the unit
This appliance is for indoor use only.
Rating: This unit must be only connected to a 220-240 V
/ 50 Hz earthed outlet.
Installation must be in accordance with regulations of the
country where the unit is used.
If you are in any doubt about the suitability of your electrical supply have it
checked and, if necessary, modified by a qualified electrician.
This air conditioner has been tested and is safe to use. However, as with any
electrical appliance - use it with care.
Disconnect the power plug from socket before dismantling, assembling or
cleaning.
Avoid touching any moving parts within the appliance.
Never insert fingers, pencils or any other objects though the guard
This appliance can be used by children aged from 8 years and above and
persons with reduced physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given supervision or instruction
concerning use of the appliance in a safe way and understand the hazards
involved. Children shall not play with the appliance. Cleaning and user
maintenance shall not be made by children without supervision.
Do not leave children unsupervised with this appliance.
Do not clean the unit by spraying it or immersing it in water.
Never connect the unit to an electrical outlet using an extension cord. If an outlet
is not available, one should be installed by a qualified electrician.
Never operate this appliance if the cord or plug is damaged. Ensure the power
cord is not stretched or exposed to sharp objects/edges.
The power cord must not be immersed in water, as this could result in electric
shock.
A damaged supply cord should be replaced by the manufacturer or a qualified
electrician in order to avoid a hazard.
Any service other than regular cleaning or filter replacement should be
performed by an authorized service representative. Failure to comply could
result in a voided warranty.
When defrosting and cleaning the appliance, only use tools recommended by
the manufacturer.
Do not use the appliance for any other purpose than its intended use.
The air conditioner unit must always be stored and transported upright,
otherwise irreparable damage may be caused to the compressor; if in
doubt we suggest waiting at least 24 hours before starting the unit.
Avoid restarting the air conditioning unit unless 3 minutes have passed since
being turned off. This prevents damage to the compressor.

Page 4 of 15
Never use the mains plug or an external timer as a
switch to start and stop the air conditioning unit. Use
the provided ON/OFF button located on the control
panel.
Always place the unit on a dry and stable surface.
The appliance should not be installed in laundry or wet
rooms
The appliance must be placed in a room without
sources of ignition (for example: open flames, an
operating gas appliance or an operating electric heater).
R290 refrigerant gas complies with European
environmental directives.
R290 has a low GWP (Global Warming Potential) of 3.
The air conditioner contains about 215 g of R290 refrigerant gas.
Do not use or store in an unventilated space with an area smaller than 10.3m2 per
unit. The room must be such as to prevent stagnation of possible leaks of
refrigerant gas as there could be a danger of fire or explosion hazard should the
refrigerant come into contact with electric heaters, stoves or other sources of
ignition.
If the appliance is installed, used or stored in an unventilated room, the room must
be such as to prevent stagnation of possible leaks of refrigerant gas as there could
be a danger of fire or explosion should the refrigerant come into contact with
electric heaters, stoves or other sources of ignition.
Refrigerant gas may be odourless.
Do not use the product and contact the retailer for advice, if damage has occurred
to the unit which may have compromised the refrigerant system.
Any repairs or maintenance must only be carried out on the unit by a suitably
qualified engineer. Before opening and servicing the unit the authorized
engineer must be in possession of a copy of the manufacturer’s service manual
and must follow the safety information contained within it to ensure all hazards are
minimized.
The refrigerant system should not be perforated or punctured.
Energy Saving and Unit Safety Protection Tips
Do not cover or restrict the airflow from the outlet or inlet grills.
For maximum performance the air conditioner should be situated at least 50cm
from the walls or other objects.
Keep the filters clean. Under normal conditions, filters should only need
cleaning once every three weeks (approximately). Since the filters remove
airborne particles, more frequent cleaning maybe necessary, depending on the
air quality.
For the initial start-up set the fan speed to maximum and the thermostat to 4-5
degrees lower than the current temperature. After, set the fan switch to low and
set the thermostat to your desired setting.
To protect the unit we recommend the unit should only be used when the room
temperature is between 7°C and 35°C. If the temperature is below this use
electrical heating to raise the temperature above 10⁰C before starting the unit.

Page 5of 15
FEATURES
FEATURES
Self-evaporative system - no external water tank needed
Powerful but compact
Hidden display on front of the unit
Enhanced design with hot air outlet positioned higher – this allows for improved
performance with the use of a short hose
24 hour programmable timer function – allows you to choose when the unit operates.
2 speed fan, Low and High for best balance
between quiet operation and
maximum airflow
Compressor protection technology

Page 6 of 15
DIAGRAM
ACCESSORIES
Control Panel
TOP VIEW
LEFT VIEW
FRONT VIEW
RIGHT VIEW
BACK VIEW
Display Panel
Air Inlet
Power cable
Handle
Air Inlet
Upper
drainage
port
Lower
Drainage
port
Slide bar
Fishtail adaptor
Exhaust hose
FRONT VIEW
Remote control
FRONT VIEW
Exhaust hose connector
FRONT VIEW

Page 7 of 15
INSTALLATION
Warning：Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed
on an even surface.
1. Assemble the fishtail adaptor on to the hose, by extending the end of the hose and
twisting the fishtail into position (At least 3 full rotations)
2. Assemble the Exhaust hose connector on to the other end of the hose, by extending the
opposite end of the hose and twisting the outlet into position (At least 3 full rotations)
3. Attach the exhaust hose connector onto to the exhaust outlet on
the rear of the air conditioner body, by pushing into position.
4. Make sure the unit is upright and there are no obstructions to
the air inlets and outlet grills. A minimum of 50cm clearance
should be left between the inlet/outlet grills and any
obstruction.

Page 8 of 15
INSTALLATION OF WINDOW KIT
1. Partially open the window and then fix the slide bare into the opening in the window, by
putting it into position before closing the window onto it to seal the gap.
2. Push the fishtail adaptor into the slot in the slide bar
Note: The slide bar is only designed to be installed with sliding or sash windows or doors.
The slidebar is not designed or to be used with any other style of window. However
the fish tail adaptor can be used with most windows / doors. When using the
cooling mode ensure that the opening is left as small as possible.
The best form of installation is through a wall duct.
By properly venting you expel hot air from your room while efficiently cooling it.
Important safeguards
The length of the soft hose extends from 28 cm to 150 cm. If hose is
extended above this length the unit may malfunction and this can
invalidate the warranty.
The outlet vent must be well ventilated and not obstructed as this will
cause the unit to overheat.
Avoid bending the air hose more than 30 degrees.

Page 9 of 15
OPERATION AND SETTINGS
CONTROL PANEL & FUNCTION
POWER BUTTON
Press to turn unit “ON” or “OFF”
MODE BUTTON
Pressing this button will select between the COOL, DRY (dehumidify) and FAN modes.
The lights next to the button indicate the currently running mode.
COOL MODE: Cold air will be expelled through the front of the unit and hot air will be expelled
through the vent hose.
DRY (DEHUMIDIFIER) MODE: The unit should be set up without a vent hose, moisture is
extracted from the air that passes through the unit. Continuous drainage should be set up for
the moisture collected (Drainage pipe not included).
FAN MODE: No cooling effect, circulates air within the room, vent pipe not required.
UP & DOWN BUTTONS
During cooling function – These buttons raise or lower the temperature by 1oC for each
press. The minimum temperature is 16oC and max. 31oC.
SPEED BUTTON
Press to select either LOW or HIGH fan speed. The lights next to the button will indicate
the fan speed currently selected.
NOTE: In dehumidifying function, this button is invalid as the unit is designed to run at low
speed in dehumidifying mode.

Page 10 of 15
SLEEP MODE
Press the Sleep button to enter sleep mode, the default fan speed is low and the Sleep
mode indicator led will illuminate.
When the sleep mode is turned on:
After one hour the set temperature will increase by 1 degree Celsius, after another hour
the set temperature will increase by another degree, and will then remain set at that
temperature.
Please note:
Sleep mode cannot be used in dry and fan modes.
If internal tank becomes full, the machine will turn off and sleep mode will be
cancelled.
TIMER BUTTON
The in-built timer will allow you to set the unit to turn on or turn off after a set period of
time, Please note only one timer can be used at any time.
ON TIMER – The timer will turn on the unit automatically after the time set has elapsed.
1. With the unit turned off, press the TIMER button, then set the number of hours’ time
you desire the unit to start by using the UP and DOWN buttons.
2. Once the set time has elapsed, the unit will turn on automatically.
3. Press the POWER button before the time has elapsed and the unit will turn on as
normal and the timer will be cancelled
4. The function and fan speed can be set whilst setting the timer.
OFF TIMER – The timer will turn off the unit automatically after the time set has elapsed.
1. While the unit is operating, press the TIMER button then set the number of hours’
time you desire the unit to stop by using the UP and DOWN buttons.
2. Once the set time has elapsed, the unit will turn off automatically.
3. Press the POWER button before the time has elapsed, the setting time will be
cancelled and the unit will turn off.
TANK FULL INDICATOR
When illuminated this indicates that the internal water tank is full and requires emptying,
following the information provided in the water drainage section.
LED DISPLAY
The display indicates the current target temperature or the remaining timer settings. When
the set temperature or the timer is adjusted, the new setting is shown.
The display is also used to show error codes. Should a fault occur, see ERROR CODES.
CHANGE BETWEEN FARENHEIT AND CELCIUS
To change the unit of measurement shown on the display, press both the UP and DOWN
buttons at the same time