ElectrIQ P16HP User manual

Page 1 of 15
USER MANUAL
PORTABLE AIR CONDITIONER WITH HEATPUMP
P16HP / P18HP
Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and
keep it safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

Page 2 of 15
CONTENTS
SAFETY INSTRUCTIONS
3
FEATURES AND PARTS LIST
5
INSTALLATION
7
OPERATION AND SETTINGS
9
WATER-DRAINAGE
11
MAINTENANCE
12
TROUBLESHOOTING
13
APPENDIX
14

Page 3 of 15
SAFETY INSTRUCTIONS
IMPORTANT!
Carefully read the instructions before operating the unit
This appliance is for indoor use only.
Rating: This unit must be only connected to a 220-240 V /
50 Hz earthed outlet.
Installation must be in accordance with regulations of the
country where the unit is used.
If you are in any doubt about the suitability of your electrical supply have it checked
and, if necessary, modified by a qualified electrician.
This air conditioner has been tested and is safe to use. However, as with any
electrical appliance - use it with care.
Disconnect the power plug from socket before dismantling, assembling or cleaning.
Avoid touching any moving parts within the appliance.
Never insert fingers, pencils or any other objects though the guard.
This appliance can be used by children aged from 8 years and above and persons
with reduced physical, sensory or mental capabilities or lack of experience and
knowledge if they have been given supervision or instruction concerning use of the
appliance in a safe way and understand the hazards involved. Children shall not
play with the appliance. Cleaning and user maintenance shall not be made by
children without supervision.
Do not leave children unsupervised with this appliance.
Do not clean the unit by spraying it or immersing it in water.
Never connect the unit to an electrical outlet using an extension cord. If an outlet
is not available, one should be installed by a qualified electrician.
Never operate this appliance if the cord or plug is damaged. Ensure the power
cord is not stretched or exposed to sharp objects/edges.
The power cord must not be immersed in water, as this could result in electric
shock.
A damaged supply cord should be replaced by the manufacturer or a qualified
electrician in order to avoid a hazard.
Any service other than regular cleaning or filter replacement should be performed
by an authorized service representative. Failure to comply could result in a voided
warranty.
When defrosting and cleaning the appliance, only use tools recommended by the
manufacturer.
Do not use the appliance for any purpose other than its intended use.
The air conditioner must always be stored and transported upright,
otherwise irreparable damage may be caused to the compressor; if in doubt
we suggest waiting at least 24 hours before starting the unit.
Avoid restarting the air conditioner unless 3 minutes have passed since being
turned off. This prevents damage to the compressor.
Never use the mains plug or an external timer as a switch to start and stop the air
conditioner. Use the provided ON/OFF button located on the control panel.
Always place the unit on a dry and stable surface.
The appliance should not be installed in laundry or wet rooms

Page 4 of 15
The appliance must be placed in a room without sources of ignition (for example:
open flames, an operating gas appliance or an operating electric heater).
R290 refrigerant gas complies with European environmental directives. R290 has
a low GWP (Global Warming Potential) of 3.
The P16HP contains about 225 g of R290 refrigerant gas, and the P18HP contains
about 300g of R290 refrigerant gas
Do not use or store in unventilated spaces with an area smaller than 10.8 m2 per
unit for P16HP and 14.4 m2 per unit for P18HP. The room must be such as to
prevent stagnation of possible leaks of refrigerant gas as there could be a danger
of fire or explosion hazard should the refrigerant come into contact with electric
heaters, stoves or other sources of ignition.
Do not use the product and contact the retailer for advice, if damage has occurred
to the unit which may have compromised the refrigerant system.
Refrigerant gas may be odourless.
Do not open the air conditioner, to attempt service or repair the unit. Any internal
servicing of the unit must be carried out only by the manufacturer or its authorized
technicians.
Any repairs or maintenance must only be carried out on the unit by a suitably
qualified engineer. Before opening and servicing the unit the authorized engineer
must be in possession of a copy of the manufacturer’s service manual and must
follow the safety information contained within it to ensure all hazards are minimized.
The refrigerant system should not be perforated or punctured.
ENERGY SAVING AND UNIT SAFETY PROTECTION TIPS
Do not cover or restrict the airflow from the outlet or inlet grills.
For maximum performance the air conditioner should be situated at least 50cm from the
walls or other objects.
Keep the filters clean. Under normal conditions, filters should only need cleaning once
every three weeks (approximately). Since the filters remove airborne particles, more
frequent cleaning maybe necessary, depending on the air quality.
For the initial start-up set the fan speed to maximum and the thermostat to 4-5 degrees
lower than the current temperature. After, set the fan to low and set the thermostat to your
desired setting.
To protect the unit we recommend the unit should only be used when the temperature of
the room is between 7°C and 35°C. If the temperature is below this use electrical
heating to raise the temperature above 10⁰C before starting the unit.

Page 5 of 15
FEATURES AND PARTS LIST
FEATURES
Full climate control, cooling, heating, fan and dehumidifier
Self-evaporative system - no external water tank needed
Powerful but compact
LED screen, indicates temperature and operation mode
Enhanced design with hot air outlet positioned higher – This allows for improved
performance with the use of a short hose
24 hour programmable timer function – Allows you to choose when the unit operates.
3 speed fan Low, Medium and High for best balance between quiet operation and
maximum airflow
Compressor protection technology

Page 6 of 15
PARTS LIST
ACCESSORIES
Rear cover
SIDE VIEW
Castor
FRONT VIEW
Control Panel
REAR VIEW
Plug
Air
Inlet
Exhaust Hose
Fishtail Connector
Slide Bar
Remote Control
Exhaust hose connector

Page 7 of 15
INSTALLATION
Warning：Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed on
an even surface.
1. Assemble the fishtail adaptor on to the hose, by extending the end of the hose and
twisting the fishtail into position (At least 3 full rotations)
2. Assemble the Exhaust hose connector on to the other end of the hose, by extending the
opposite end of the hose and twisting the outlet into position (At least 3 full rotations)
3. Attach the Exhaust hose connector to the
rear of the air conditioner
4. Make sure the unit is upright and there are no
obstructions to the air inlets and outlet grills. A minimum
of 50cm clearance should be left between the inlet/outlet
grills and any obstruction.

Page 8 of 15
INSTALLATION OF WINDOW KIT
1. Partially open the window and then fix the slide bar into the opening in the window, by
putting it into position before closing the window onto it to seal the gap.
2. Push the fishtail adaptor into the slot in the slide bar
Note: The slide bar is only designed to be installed with sliding or sash windows or doors.
The slidebar is not designed or to be used with any other style of window. However
the fish tail adaptor can be used with most windows /doors. When using cooling or
heating modes ensure that the opening is left as small as possible.
The best form of installation is through a wall duct. By properly venting you expel
hot air from your room while efficiently cooling it.
IMPORTANT SAFEGUARDS
The length of the soft hose extends from 28 cm to 150 cm. If hose
is extended above this length the unit may malfunction and this
can invalidate the warranty.
The outlet vent must be well ventilated and not obstructed as this
will cause the unit to overheat.
Avoid bending the air hose more than 30 degrees.

Page 9 of 15
OPERATION AND SETTINGS
CONTROL PANEL & FUNCTION
POWER BUTTON
Press to turn unit “ON” or “OFF”
MODE
Pressing this button will select between the Cooling , Heating , Auto, Fan and
Dehumidify modes.
COOLING MODE: Cold air will be expelled through the top of the unit and hot air will
be expelled through the vent hose.
HEATING MODE: Hot air will be expelled through the top of the unit and cold air will be
expelled through the vent hose. Continuous drainage should be set up for the moisture
collected.
DEHUMIDIFY MODE: The unit should be set up without a vent hose, moisture is
extracted from the air that passes through the unit. Continuous drainage should be set
up for the moisture collected.
FAN MODE: No cooling effect, circulates air within the room, vent pipe not required.
AUTO MODE: The unit will change between Heating, cooling and fan modes depending
on the desired temperature set.
TEMPERATURE UP & DOWN
During cooling and heating modes – These buttons raise or lower the temperature by 1oC
for each press. The minimum temperature is 16oC and max. 31oC.
FAN SPEED
Press to select either LOW, MEDIUM or HIGH fan speed.
NOTE: In dehumidifying mode, this button is invalid as the unit is designed to run at low
speed in dehumidifying mode.

Page 10 of 15
SLEEP MODE
Press the SLEEP button to enter sleep mode, the default fan speed is low and the Sleep
mode indicator led will illuminate.
When the sleep mode is turned on:
After one hour the set temperature will increase by 1 degree Celsius, after another hour
the set temperature will increase by another degree, and will then remain set at that
temperature.
Please note:
Sleep mode cannot be used in dry and fan modes.
If internal tank becomes full, the machine will turn off and sleep mode will be
cancelled.
SWING BUTTON
After machine is on and mode selected, press this button and the louver will swing
continuously up and down; by pressing this button again the movement will stop and the
louver remain fixed in position.
TIMER BUTTON
The in-built timer will allow you to set the unit to turn on or turn off after a set period of
time, Please note only one timer can be used at any time.
ON TIMER – The timer will turn on the unit automatically after the time set has elapsed.
1. With the unit turned off, press the TIMER button, then set the number of hours’ time
you desire the unit to start by using the UP and DOWN buttons.
2. Once the set time has elapsed, the unit will turn on automatically.
3. Press the POWER button before the time has elapsed and the unit will turn on as
normal and the timer will be cancelled
4. The function and fan speed can be set whilst setting the timer.
OFF TIMER – The timer will turn off the unit automatically after the time set has elapsed.
1. While the unit is operating, press the TIMER button then set the number of hours’
time you desire the unit to stop by using the UP and DOWN buttons.
2. Once the set time has elapsed, the unit will turn off automatically.
3. Press the POWER button before the time has elapsed, the setting time will be
cancelled and the unit will turn off.
TANK FULL INDICATOR
When the internal water tank is full, the unit will stop operation, and the TANK FULL
indicator will illuminate. To restart operation, empty the water tank following the
information in the Water drainage section
LED DISPLAY
The display indicates the current target temperature or the remaining timer settings. When
the set temperature or the timer is adjusted, the new setting is shown.
The display is also used to show error codes. Should a fault occur, see ERROR CODES.

Page 11 of 15
REMOTE CONTROL
The functions on the remote are the same as those on the main control
panel
WATER-DRAINAGE
MANUAL DRAINAGE:
1. When the internal water tank is full the unit will stop working and the TANK FULL indicator
will illuminate.
2. Shut off the unit and unplug. Try not to move the model abruptly as this may cause water
to spill out from internal water tank.
3. Place a tray under the water plug.
4. Unscrew the water plug (A) and remove the rubber bung (B) - water will drain from the
internal tank.
5. When drained replace the rubber bung and screw the water plug back into place
CONTINUOUS DRAINAGE:
1. Unscrew the water plug (A) and remove the rubber
bung (B).
2. Connect a suitably sized water pipe to the port.
3. You can plumb this pipe into your current plumbing
system, lead it outside or use a water pump.
Note: This model has a self-evaporative function, which reduces the need to empty the water
tank while in cooling mode. If the unit is vented correctly most of the water is reused to
cool the condenser coils and any excess is evaporated. Please do not use continuous
drainage if you intend to use the self-evaporating facility. In heating or dehumidifier mode
we advise to use the continuous drainage.
1. POWER – ON/OFF Switch
2. MODE – Operation Mode
3. TIMER – Timer Mode
4. SPEED – Fan Speed Selector
5. TEMP+ - Temperature Up
6. TEMP- – Temperature Down
7. SLEEP
8. SWING

Page 12 of 15
MAINTENANCE
CLEANING
Please shut off the unit and unplug from the mains before cleaning or performing any
maintenance
CLEAN THE SURFACE
Clean the plastic housing with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause
irreversible damage.
AIR FILTER CLEANING
a) Clean the air filters every 2 weeks. If the air filter is blocked
with dust, the unit’s performance will be significantly affected.
b) Disconnect the power plug from the socket before
dismantling, assembling or cleaning
c) Open the air filter covers and remove the carbon (if
installed) and washable mesh filter
d) Hoover gently the carbon filter and do not wash
e) Wash the mesh air filters by immersing
them in warm (about 40℃) water with a
neutral detergent.
f) Rinse it and then dry it thoroughly.
g) Carefully re-install air filters back into their cover
Please note: If in use, the optional active carbon filter (cloth) should be replaced every 3-6
months based on the environment.
END OF SEASON MAINTENANCE：
1. Pull out the plug from the drainage hole and empty the internal tank. You can also drain the
water by leaning the unit.
2. Then switch the unit to low fan mode.
3. Keep the unit in this mode for half day - until the conduit is dried. Doing this helps to keep
the inside of the unit dry and prevents mould developing
4. Turn off the unit and pull out the plug.
5. Coil the wire and bind it together, then put it into the accessories space.
6. Separate the air-exhausted pipe and store it safely.
7. Cover the unit and keep it in a dry place.
8. Take the batteries out of remote control and store, or dispose, them safely
Keep all accessories with the unit ready for next season.

Page 13 of 15
TROUBLESHOOTING
Do not repair or disassemble the unit by yourself, unauthorized repair attempts will invalidate
the warranty and may cause bodily harm.
Problem
Reasons
Solutions
The unit does
not work
No power supply
Power-on and turn on the unit.
Water-full indicator illuminated
Drain the internal water tank
Timer function is active
Cancel Timer function
Room temperature too low or too
high
Use only in ambient temperatures
between 7-35℃
The unit does
not seem to
perform.
In direct sunlight
Draw the curtains, UV affects RC
Windows or doors open.
Large amount of people or a heat
source in the room.
Close windows and turn on another air
conditioner
Filter is very dirty
Clean or change the air filter
Air inlet or air outlet is blocked
Clear out debris
Room temperature is lower than
setting temperature
Change the setting temperature
The unit loud
The unit is not put on flat surface
Put the unit on flat and hard surface
Compressor
does not work
Overheating protection is
active
Check venting.
Restart the unit after 5 minutes when
compressor has cooled
Remote control
doesn’t work
Operating distance is too far.
Move remote control closer to the unit
and make sure it aims at the air-outlet
grille
Control panel has not received
the signal from remote control.
The batteries are flat
Replace the batteries
E0
Room temperature abnormal or
there is electrical short on
temperature sensor
Temperature not within 7-35 C operating
range. If temperature within operating
range refer to Service Centre (check
room temperature sensor or relevant
circuit)
E3
Pipe temperature sensor failure
Switch off the unit, let it rest for min 30
minutes and restart. If still error please
contact the service centre.
E2/E4
Water tank is full inside the
machine
Drain out water from drain port at bottom
rear of the unit.
If the above solutions do not resolve the problem please contact the service centre.

Page 14 of 15
APPENDIX
Disposal: Do not dispose this product as unsorted municipal waste. Collection
of such waste must be handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can
deposit your old electrical products. Customers will be able to take any old
electrical equipment to participating civic amenity sites run by their local
councils. Please remember that this equipment will be further handled during the recycling
process, so please be considerate when depositing your equipment. Please contact the local
council for details of your local household waste recycling centres.
TECHNICAL DATA
P16HP
P18HP
Capacity
Cooling: 4.6 kWh /
16,000 BTU
Cooling: 5.2 kWh /
18,000 BTU
Heating: 4.2 kWh /
14,000 BTU
Heating: 4.7 kWh /
16,000 BTU
Rated Input
Cooling: 1769W
Cooling: 2000W
Heating: 1826W
Heating: 2043W
Running Current
Cooling: 8.0 Amps
Heating: 8.4 Amps
Cooling: 9.3 Amps
Heating: 9.4 Amps
Noise (sound
power)
<65dB(A)
<65dB(A)
Permitted Excessive
Operating
Pressure
1.0/2.6MPa
1.0/2.6MPa
Maximum Allowable
Pressure
1.2/3.2Mpa
1.2/3.2Mpa
Power Supply
220-240V/50Hz
220-240V/50Hz
Net Weight
29 kgs
30 kgs
Refrigerant Quantity
225g
300g
Dimension(L*D*H)
470*370*764 mm
470*370*764 mm
Unit must be vented outside when in Air Cooling and Heating mode.
For the purposes of EU regulation EN12102 this is a local air
conditioner and produces less than 65dB(A) sound energy.

Page 15 of 15
electriQ UK SUPPORT
www.electriQ.co.uk/support
Please, for your own convenience, make these simple checks before calling
the service line.
If the unit still fails to operate call: 0871 620 1057 or complete the online form
1. Has the unit been standing upright for at least 2 hours?
2. Is the unit plugged into the mains?
3. Is the fuse OK?
4. Switch the unit off and wait three minutes to see if the issue is resolved.
Restart the unit.
5. Check if the water tank is full.
Office hours: 9AM - 5PM Monday to Friday
Unit J6, Lowfields Business Park
Lowfields Way, Elland
West Yorkshire, HX5 9DA