ElectrIQ ECOSILENT12HPWE User manual

USER MANUAL
electriQ PORTABLE AIR CONDITIONER
WITH HEAT PUMP AND WIFI
ECOSILENT12HPW
12,000 BTU
ECOSILENT12HPWE
ECOSILENT14HPW
14,000 BTU
ECOSILENT14HPWE
Thank you for choosing electriQ
Please read this user manual before using this innovative Air Conditioner and keep it
safe for future reference.
Visit our page www.electriQ.co.uk for our entire range of Intelligent Electricals

1
CONTENTS
SAFETY
2
FEATURES AND PARTS LIST
4
INSTALLATION
5
OPERATION
7
REMOTE CONTROL
8
SMART INDICATOR
8
EMPTYING THE INTERNAL WATER TANK
9
WIFI APP CONTROL
10
SETTING UP THE APP
10
CONNECTING THE AIR CONDITIONER
12
CONTROLLING YOUR DEVICE
14
SMART SCENES
17
CLEANING AND MAINTENANCE
20
TROUBLESHOOTING
21
ERROR CODES
21
SUPPORT
22
TECHNICAL SPECIFICATION
23

2
SAFETY INSTRUCTIONS
Important!
•Carefully read the instructions before operating the unit
•This appliance is for indoor use only.
•Rating: This unit must be only connected to a 220-240 V / 50 Hz
earthed outlet.
•Installation must be in accordance with regulations of the country where the unit is used.
•If you are in any doubt about the suitability of your electrical supply have it checked and,
if necessary, modified by a qualified electrician.
•This air conditioner has been tested and is safe to use. However, as with any electrical
appliance - use it with care.
•Disconnect the power from the appliance before dismantling, assembling or cleaning.
•Avoid touching any moving parts of the appliance.
•Never insert fingers, pencils or any other objects though the guard
•This appliance is not intended for use by persons (including children) with reduced
physical, sensory or mental capabilities. It is also not intended for use by those with a
lack of experience and knowledge, unless they have been given supervision or instruction
concerning the use of the appliance by a person responsible for their safety.
•Do not leave children unsupervised with this appliance.
•Do not clean the unit by spraying it or immersing it in water.
•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not
available, one should be installed by a qualified electrician.
•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not
stretched or exposed to sharp objects/edges.
•A damaged supply cord should be replaced by the manufacturer or a qualified electrician
in order to avoid a hazard.
•Any service other than regular cleaning or filter replacement should be performed by an
authorised service representative. Failure to comply could result in a voided warranty.
•Do not use the appliance for any purpose other than its intended use.
•The air conditioner unit must always be stored and transported upright, otherwise
irreparable damage may be caused to the compressor; if in doubt we suggest waiting at
least 24 hours before starting the unit.
•Avoid restarting the air conditioning unit unless 3 minutes have passed since being
turned off. This prevents damage to the compressor.
•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use
the provided ON/OFF button located on the control panel.
•Always place the unit on a dry and stable surface.
•The appliance should not be installed in laundry or wet rooms.
•The appliance must be placed in a room without sources of ignition (for example: open
flames, an operating gas appliance or an operating electric heater).

3
•R290 refrigerant gas complies with European environmental directives.
•R290 has a low GWP (Global Warming Potential) of 3.
•The air conditioner contains about 300 g of R290 refrigerant gas.
•Do not use or store in an unventilated space with an area smaller than 14.4 m2per unit.
•The room must be such as to prevent stagnation of possible leaks of refrigerant gas as
there could be a danger of fire or explosion should the refrigerant come into contact with
electric heaters, stoves or other sources of ignition.
•Refrigerant gas may be odourless.
•Do not use the product and contact the retailer for advice, if damage has occurred to the
unit which may have compromised the refrigerant system.
•Any repairs or maintenance must only be carried out on the unit by a suitably qualified
engineer. Before opening and servicing the unit the authorised engineer must be in
possession of a copy of the manufacturer’s service manual and must follow the safety
information contained within it to ensure all hazards are minimized.
•The refrigerant system should not be perforated or punctured.
Energy Saving and Unit Safety Protection Tips
•Do not cover or restrict the airflow from the outlet or inlet grills.
•For maximum performance the minimum distance from a wall or objects should be
50cm.
•Keep the filters clean. Under normal conditions, filters should only need cleaning once
every three weeks (approximately). Since the filters remove airborne particles, more
frequent cleaning maybe necessary, depending on the air quality.
•For the initial start-up set the fan speed to maximum and the thermostat to 5 degrees
lower than the current temperature. After, set the fan switch to low and set the
thermostat to your desired setting.
•To protect the unit, we recommend not using the cooling function when the ambient
temperature is higher than 35oC.

4
FEATURES AND PARTS LIST
•4 in 1 Cooling, Heating, Fan and Dehumidifier great for Rooms up to 20 sqm.
•5 speed DC fan: balancing quiet operation with performance.
•SmartCool Logic for Improved Energy Efficiency.
•HEPA Filter for Air Purification
•24 Hours Start / Stop Timer
•Digital Thermostat.
•Auto-Restart to retain the settings in the event of power failure.
•WIFI control from app
•Castors and Handles for Enhanced Portability
Control Panel
Rear Housing
Front Housing
Castors
Plug
Carry Handle
Exhaust Hose
Window Slide Bar
Upper
Air Inlet
Lower
Air Inlet
Louvre
(Air Outlet)
Smart
Indicator
Exhaust
Outlet

5
INSTALLATION
WARNING: Before using this unit, please keep it upright for at least 3-4 hours.
This unit can easily be moved from one room to another. While moving the unit please note that it must
always be kept upright and then placed on an even surface.
1. Attach the fishtail connector to the end of the hose, by
extending the end and twisting until firmly attached (At least
3 full rotations).
2. Attach the connector on the opposite end of the pipe to the exhaust outlet
on the rear of the appliance by putting into position and twisting to lock in
place.
3. Make sure the unit is upright and there are no obstructions to the air
inlets and outlet grills.
INSTALLATION OF WINDOW KIT
The window kit (slide bar and fishtail) can be used with sliding windows and doors. For other types of window, the
fishtail should be used on its own.
1. Partially open the window and place the
extended slide bar in position before closing
the window onto it.
2. Fix the fishtail adaptor into the
opening on the slide bar
3. Fix the exhaust connector on
the opposite end of the exhaust
hose to the exhaust outlet on
the rear of the air conditioner.

6
INSTALLING THE HEPA FILTER (OPTIONAL)
The air conditioner can accommodate a HEPA filter which will purify the
air expelled back into the room in any operating mode. These can be
purchased from the stockist using the code: FIL-ECOSILENTHEPA.
The HEPA filter should be unwrapped and installed in the upper air inlet.
To install, remove the upper filter frame from the air conditioner by
pressing the two clips on the top of the filter frame. Place the HEPA filter
within the filter frame before refitting onto the unit.
In order to maintain performance, the filter should be regularly
vacuumed. The filter should be replaced every six months, depending on
usage and air quality.
NOTES:
•The window kit is only designed to be installed with sliding or sash windows or doors. The window
kit is not designed or to be used with any other style of windows.
•The fish tail adaptor can be used without the slide bar with most windows / doors.
•When using the air conditioner ensure that the opening left around the fishtail is as small as
possible to ensure the unit performs efficiently.
•The best form of installation is through a wall duct. By properly venting you expel hot air from your
room while efficiently cooling it.
•Your air conditioner should be used without the vent pipe in dry mode. When using dry mode
ensure that an external water tank is used, monitored and regularly emptied before overflowing.
Permanent plumbing can be also installed for dry mode or an external uplift water pump can be
set up for unattended use.
IMPORTANT SAFEGUARDS
The length of the soft hose extends from approximately 35 cm to 200 cm. If hose is extended above this
length, the unit may malfunction which can invalidate the warranty. The outlet vent must be well
ventilated and not obstructed as this will cause the unit to overheat. Keep the hose as straight and short as
possible and avoid bending the air hose by more than 30 degrees in order to maintain the performance of
the unit. Excessive bends in the hose may prevent the unit from expelling the hot air, which can lead to
internal damage which would invalidate the warranty.

7
OPERATION
Press the POWER button to turn the unit ON or OFF.
Press the MODE button to cycle between the 5 modes, the indicator for the selected mode will be
illuminated.
COOL: The room is cooled with the cold air expelled through the front air outlet while hot air is
expelled through the vent pipe. The desired room temperature can be set between 17 and 30 degrees
using the + and –buttons, and the fan speed can be changed using the SPEED button.
HEAT: The room is heated with the warm air expelled through the front air outlet while cold air is
expelled through the vent pipe. The desired room temperature can be set between 16 and 32 degrees
using the + and –buttons, and the fan speed can be changed using the SPEED button. We advise for
continuous drainage to be set up in HEAT mode.
FAN (AIR PURIFIER): The fan speed can be changed pressing the SPEED button. When used with the
optional HEPA filter, the appliance will work as an effective air purifier.
DRY (DEHUMIDIFY): Should be operated without the vent hose, but with continuous drainage to
remove moisture from the air. The display will show dH while in dry mode. The fan speed is set to low
and is not adjustable.
SMART COOL: An intelligent cooling mode where the fan speed is automatically adjusted based on the
amount of cooling required. Attempts to change the fan speed will move the unit into COOL mode.
Repeatedly press the SPEED button to cycle through the five fan speeds. Each time the SPEED button
is pressed, the fan speed will be displayed. The fan speed can be changed between F1 (Low) to F5
(High). The LED indicators will also illuminate to show the fan speed as below:
F1 –Low, F2 –Low and Mid, F3 –Mid, F4 –Mid and High, F5 –High.
The fan speed cannot be changed in SMARTCOOL and DRY modes.
Press to enter sleep mode. The sleep indicator will be illumined and all other indicators will be turned
off. In sleep mode, the appliance works at low fan speed. Press SLEEP again to exit sleep mode.
The SLEEP button is also used to set up the WIFI function. See the WIFI SMART CONTROL section for
further information.
The timer functions cannot be combined or repeated.
POWER ON TIMER
With the appliance in standby, press the TIMER button to set the power-on timer. Use the + and -
buttons to adjust the duration of the timer (1 to 24 hours). The Timer indicator will turn on and the
unit will start after the selected number of hours.
POWER OFF TIMER
With the appliance running with the desired settings, press the TIMER button to set the power-off
timer. Use the + and - buttons to adjust the duration of the timer (1 to 24 hours). The timer indicator
will illuminate and the unit will stop after selected number of hours.
Used to adjust temperature in HEAT/COOL/SMART COOL modes and to set the duration of the TIMER.
The buttons are not used in FAN or DRY modes. Press both buttons together to change between
displaying the temperature in Celsius and Fahrenheit.
Press this button to enable the swing function. The louvres will slowly move from side to side. If
swing is pressed again the louvres will stop in their current position. Press and hold the SWING
button for 3 seconds to turn the indicator lights on or off.

8
REMOTE CONTROL
NOTE: The design of the remote may vary from the diagram, due to
continuous product improvement.
SMART INDICATOR LED
The air conditioner contains a Smart Indicator which changes colour to show from a distance what mode
the air conditioner is set to.
HEAT MODE
The indicator will display Red.
COOL MODE
The indicator will display Blue.
SMART COOL MODE
The indicator will display Blue.
FAN (AIR PURIFIER) MODE
The indicator will display Green.
DRY (DEHUMIDIFY) MODE
The indicator will display Orange.
POWER
Press to turn the unit on or off.
TIMER
Press to set the timer.
DOWN
Press to decrease the desired temperature or
timer duration.
UP
Press to increase the desired temperature or
timer duration.
SLEEP
Press the sleep button to enter sleep mode.
SWING
Press swing to turn the swing function on or off.
⁰C/⁰F
Press to change between displaying the
temperature in Celsius or Fahrenheit.
FAN
Press to enter fan / air purify mode.
COOL
Press to enter cool mode.
HEAT
Press to enter heat mode.
DRY
Press to enter dry (dehumidify) mode.
HIGH
Press to enter high (F5) speed fan.
MID
Press to enter medium (F3) speed fan.
LOW
Press to enter low (F1) speed fan.
Smart Indicator