ElectrIQ P18HP User manual

P18HP
PORTABLE AIR CONDITIONER WITH HEATPUMP
USER MANUAL
Thank you for choos ng Electr Q
Please read th s user manual before us ng th s nnovat ve A r Cond t oner and keep t safe for
future reference.
V s t our page www.electr Q.co.uk for our ent re range of Intell gent Electr cals
All manuals and user guides at all-guides.com
all-guides.com

Page 2of 13
CONTENTS
1．
．．
．SAFETY INSTRUCTIONS ………………………………………………… 3
2．
．．
．FEATURES AND PARTS LIST ………………………….................. 4
3．
．．
．INSTALLATION ………………………………….…………………….….. 6
4．
．．
．OPERATION AND SETTINGS ………………………………………. 8
5．
．．
．WATER-DRAINAGE ………………………………………………….……. 9
6．
．．
．MAINTENANCE …………………………………………………………….. 10
7．
．．
．TROUBLE SHOOTING ………………………………………………….. 11
8．
．．
．APPENDIX …………………………………………………………………….. 12
All manuals and user guides at all-guides.com

Page 3of 13
SAFETY INSTRUCTIONS
Important!
•Carefully read the instructions before operating the unit
•This appliance is for indoor use only.
•Rating: This unit must be only connected to a 220-240 V / 0 Hz earthed outlet.
•Installation must be in accordance with regulations of the country where the unit is used.
•If you are in any doubt about the suitability of your electrical supply have it checked and, if necessary,
modified by a qualified electrician.
•This air conditioner has been tested and is safe to use. However, as with any electrical appliances - use
it with care.
•Disconnect the power plug from socket before dismantling, assembling or cleaning.
•Avoid touching any moving parts of the appliance.
•Never insert fingers, pencils or any other objects though the guard
•This appliance is not intended for use by persons (including children) with reduced physical, sensory or
mental capabilities. It is also not intended for use by those with a lack of experience and knowledge, unless
they have been given supervision or instruction concerning the use of the appliance by a person responsible
for their safety.
Do not leave children unsupervised with this appliance.
•Do not clean the unit by spraying it or immersing it in water.
•Never connect the unit to an electrical outlet using an extension cord. If an outlet is not available, one
should be installed by a qualified electrician.
•Never operate this appliance if the cord or plug is damaged. Ensure the power cord is not stretched or
exposed to sharp object/edges.
• A damaged supply cord should be replaced by the manufacturer or a qualified electrician in order to
avoid a hazard.
•Any service other than regular cleaning or filter replacement should be performed by an authorized
service representative. Failure to comply could result in a voided warranty.
•Do not use the appliance for any other purposes than its intended use.
•The a r cond t oner un t must always be stored and transported upr ght, otherw se rreparable
damage may be caused to the compressor; f n doubt we suggest wa t ng at least 24 hours before start ng
the un t.
•Avoid restarting the air conditioning unit unless 3 minutes have passed since being turned off. This
prevents damage to the compressor.
•Never use the mains plug as a switch to start and turn off the air conditioning unit. Use the provided
ON/OFF switch located on the control panel.
•Always place the unit on a dry and stable surface.
•The appliance should not be installed in laundry or wet rooms
Energy Sav ng and Un t Safety Protect on T ps
•Do not cover or restrict the airflow from the outlet or inlet grills.
•For maximum performance the minimum distance from a wall or objects should be 0cm.
•Keep the filters clean. Under normal conditions, filters should only need cleaning once every three
weeks (approximately). Since the filters remove airborne particles, more frequent cleaning maybe necessary,
depending on the air quality.
•For the initial startup set the fan speed to maximum and the thermostat to 4- degrees lower than the
current temperature. After, set the fan switch to low and set the thermostat to your desired setting.
•To protect the unit we recommend not using the cooling function when the ambient temperature is
higher than 3 ⁰C. To protect the unit we recommend not using the heating function when the ambient
temperature is lower than 7⁰C, use electrical heating to raise the temperature above 10⁰C than start unit.
All manuals and user guides at all-guides.com

Page 4of 13
FEATURES AND PARTS LIST
Features
Full climate control, cooling, heating and dehumidifier
Self-evaporative system - no external water tank needed
Powerful but compact
LCD screen, indicates temperature and operation mode
Enhanced design with hot air outlet positioned higher – this allows for improved performance
with the use of a short hose
24 hour programmable timer function – allows you to choose when the unit operates.
3 speed fan Low, Medium and High for best balance between quiet operation and maximum
airflow

Compressor protection technology
All manuals and user guides at all-guides.com

Page 5of 13
Parts l st
ACCESSORIES
All manuals and user guides at all-guides.com

Page 6of 13
INSTALLATION
1. Installat on
Warn ng：
：：
：Before us ng th s un t, please keep t upr ght for at least 3-4 hours.
This unit can easily be moved from one room to another.
While moving the unit please note that it must always be kept upright and then placed on an even
surface.
1. Assemble the fishtail connector on to the hose
2. Assemble the exhaust hose
3. Extend one head of the hose and screw it into the assembled adaptor at the back of the unit
anti-clockwise.
Note: to screw it into place should take no less than three rotations.
4. Installation of window kits:
Partially open the window and then fix the window kit to the window
All manuals and user guides at all-guides.com
all-guides.com

Page 7of 13
. Make sure the unit is upright and there are no
obstructions to the air inlets and outlet grills
6. Fix the other end of the hose to the air-outlet window kit
Note:
The window kit is only designed to be installed with sliding or sash windows or doors. The window kit is not
designed or to be used with any other style of windows. However the fish tail adaptor can be used with most windows
/ doors.
When using the cooling mode ensure that the opening left is as small as possible.
The best form of installation is through a wall duct.
Please note that the unit will need to be vented out in heating mode, ideally through the wall. By properly venting you
expel cold air from your room while efficiently heating it.
Important safeguards
The length of the soft hose extends from 28 cm to 1 0 cm. If hose is
extended above this length the unit may malfunction and this can
invalidate the warranty.
The outlet vent must be well ventilated and not obstructed as this
will cause the unit to overheat.
Avoid bending the air hose more than 30 degrees.
All manuals and user guides at all-guides.com

Page 8of 13
OPERATION AND SETTINGS
CONTROL PANEL & FUNCTIONS
POWER KEY
Press to turn unit “ON” or “OFF”
TEMPERATURE UP & DOWN
During cooling/heating function – These keys raise or lower the temperature by 1
o
C for each press.
The minimum temperature is 16
o
C.
SPEED
Press to select either LOW, MEDIUM or HIGH fan speed.
NOTE: In dehumidifying function, this key is invalid because the unit is designed to be low speed in
dehumidifying mode.
PROGRAMMABLE TIMER
T mer on – The timer on is used to turn on the unit automatically after the set time is over.
1. When on standby, press the TIMER key, then set the time you desire the unit to start after
by pressing the TEMP+ or TEMP- key.
2. Once the set time has come to an end, the unit will turn on automatically.
3. Press the POWER key before time out, the unit will turn on as normal and the program will
be cancelled
4. The function and fan speed can be set whilst setting the timer.
T mer off – The timer off is used to turn off the unit automatically after the setting time is over.
1. Press the TIMER key when the unit is operating, then set the time you desire the unit to
stop after by pressing TEMP+ or TEMP- key.
2. Once the set hour has come to an end, the unit will turn off automatically.
3. Press the POWER key before the time is up, the setting time will be cancelled and the unit
will turn off.
MODE
Pressing this key will select between the Cooling
/
Heating / Auto or “Dehumidify” .
LED DISPLAY
The display indicates the current target temperature or the remaining timer settings. When the set
All manuals and user guides at all-guides.com

Page 9of 13
temperature or the timer is adjusted, the new setting is shown.
The display is also used to show error codes. Should a fault occur, see ERROR CODES.
REMOTE CONTROL FUNCTION
The functions on the remote are the
same as those on the main control panel
WATER-DRAINAGE
1. Manual drainage:
1.1 When the internal water tank is full the unit will stop working and display the message
“E2” on the display.
1.2 Shut off the unit and unplug. Try not to move the model abruptly as this may cause water
to spill out from internal water tank.
1.3 Place a tray under the water plug.
1.4 Screw off the water plug and unplug the water blocker - water will drain from the
container.
1. Put the water blocker back and screw the water plug back into place
2. Continuous drainage:
2.1 Screw off the water plug and unplug the water
blocker.
2.2 Use a water pipe to connect to the water outlet.
2.3 You can plumb this pipe into your current plumbing
system, lead it outside or use a water pump.
Note: This model has a self-evaporative function, which reduces the need to empty the water tank. If
the unit is vented correctly most of the water is reused to cool the condenser coils and any excess is
evaporated. Please do not use continuous drainage if you intend to use the self-evaporating facility.
1.
POWER
POWER POWER
POWER
–
––
–
ON/OFF Switch
ON/OFF SwitchON/OFF Switch
ON/OFF Switch
2. MODE
MODE MODE
MODE –
––
– Operation Mode
Operation Mode Operation Mode
Operation Mode
3. TIMER
TIMER TIMER
TIMER –
––
– Timer Mode
Timer ModeTimer Mode
Timer Mode
4. SPEED
SPEED SPEED
SPEED –
––
– Fan Speed Selector
Fan Speed SelectorFan Speed Selector
Fan Speed Selector
5. TEMP+
TEMP+ TEMP+
TEMP+ -
--
- Temperat re Up
Temperat re UpTemperat re Up
Temperat re Up
6. TEMP
TEMPTEMP
TEMP-
--
- –
––
– T
TT
Temperat re Down
emperat re Downemperat re Down
emperat re Down
All manuals and user guides at all-guides.com

Page 10 of 13
Ma ntenance
Clean ng
Please shut off the unit and unplug from the mains before cleaning or performing any
maintenance
Clean the surface
Clean the plastic housing with a duster or a soft wet cloth.
Do not use chemical solvents (such as benzene, alcohol or gasoline) as they may cause irreversible
damage.
A r f lter clean ng
a) Clean the air filters every 2 weeks. If the air filter is blocked with dust, the
unit’s performance will be significantly affected.
b) Disconnect the power plug from socket before dismantling, assembling or
cleaning
c) Open the air filter covers and remove the carbon and washable mesh
filter
d) Hoover gently the carbon filter and do not wash
e) Wash the mesh air filters by immersing them in
warm (about 40℃) water with a neutral detergent.
f) Rinse it and then dry it thoroughly.
g) Carefully re-install air filters back into their cover
Please note: If in use, the optional active carbon filter (cloth) should be replaced every 3-6 months
based on the environment.
End of Season Ma ntenance：
：：
：
1. Pull out the plug from the drainage hole and empty the internal tank. You can also drain
the water by leaning the unit.
2. Then switch the unit to low fan mode.
3. Keep the unit in this mode for half day - until the conduit is dried. Doing this helps to keep
the inside of the unit dry and prevents mold developing
4. Turn off the unit and pull out the plug.
. Coil the wire and bind it together, then put it into the accessories space.
6. Separate the air-exhausted pipe and store it safely.
7. Cover the unit and keep it in a dry place.
8. Take the batteries out of remote control and store, or dispose, them safely
Keep all accessories with the unit ready for next season.
All manuals and user guides at all-guides.com

Page 11 of 13
Troubleshoot ng
Do not repair or disassemble the unit by yourself, unauthorized repair attempts will invalidate the
warranty and may cause bodily harm.
Trouble Reason Solut on
The unit does not
work
No power supply Power-on and turn on the unit.
Water-full indicator illuminated Drain the internal water tank
Timer function is active Cancel Timer function
Room temperature too low or too
high
Use only in ambient temperatures between
7-3
℃
The unit does not
seem to perform.
In direct sunlight Draw the curtains, UV affects RC
Windows or doors open.
Large amount of people or a heat
source in the room.
Close windows and turn on another air
conditioner
Filter is very dirty Clean or change the air filter
Air inlet or air outlet is blocked Clear out debris
Room temperature is lower than
setting temperature Change the setting temperature
The unit loud The unit is not put on flat surface Put the unit on flat and hard surface
Compressor does
not work Overheating protection is active
Check venting.
Restart the unit after minutes when
compressor has cooled
Remote control
doesn’t work
Operating distance is too far. Move remote control closer to the unit and
make sure it aims at the air-outlet grille
Control panel has not received the
signal from remote control.
The batteries are flat Replace the batteries
E0
Room temperature abnormal or
there is electrical short on
temperature sensor
Temperature not within 7-3 C operating
range. If temperature within operating range
refer to Service Centre (check room
temperature sensor or relevant circuit)
E2/E4 Water tank is full inside the machine Drain out water from drain port at bottom
rear of the unit.
If the above solutions do not resolve the problem please contact the service centre.
All manuals and user guides at all-guides.com
all-guides.com

Page 12 of 13
Disposal: Do not dispose this product as unsorted municipal waste. Collection of such
waste must be handled separately as special treatment is necessary.
Recycling facilities are now available for all customers at which you can deposit your old
electrical products. Customers will be able to take any old electrical equipment to participating
civic amenity sites run by their local councils. Please remember that this equipment will be further
handled during the recycling process, so please be considerate when depositing your equipment.
Please contact the local council for details of your local household waste recycling centres.
TECHNICAL DATA:
Capac ty
Cooling:
.2
kW
h /
18
,000 BTU
Heating:
kW
h / 17,
0
6
0 BTU
Rated Input
Cooling: 1.9
kW
Heating: 1.
9
kW
Runn ng Current
Cooling:
8.6
A
mps
Heating: 8. Amps
A r Flow
20
m
3
/h
No se
(sound power)
<
6
dB(A)
Perm tted Excess ve Operat ng Pressure
1.2
/3.
8
MPa
Max mum All
owable Pressure
1. /
Mpa
Power
Supply
220
-
240
V/ 0Hz
Net We ght
43
kgs
D mens on
(L*D*H)
410*830*440
mm
Unit must be vented outside when in Air Cooling and Heating mode.
For the purposes of EU regulation EN12102 this is a local air conditioner
and produces less than 6 dB(A) sound energy.
All manuals and user guides at all-guides.com

Page 13 of 13
Electr Q UK SUPPORT
www.Electr Q.co.uk/support
Please, for your own conven ence, make these s mple checks
before call ng the serv ce l ne.
If the un t st ll fa ls to operate call: 0871 620 1057 or complete
the onl ne form
1. Has the un t been stand ng upr ght for at least 2 hours?
2. Is the un t plugged nto the ma ns?
3. Is the fuse OK?
4. Sw tch the un t off and wa t three m nutes to see f the ssue
s resolved. Restart the un t.
5. Check f the water tank s full.
Off ce hours: 9AM - 5PM Monday to Fr day
www.Electr Q.co.uk
Un t 2, The Nursery
Berr stow Lane
South Normanton
Derbysh re, DE55 2FX
All manuals and user guides at all-guides.com