Electrolux EXI09HD1W User manual

EXI09HD1W
EXI12HD1W
EXI18HD1W
EXI22HD1W
SPLIT TYPE ROOM AIR
CONDITIONER
CLIMATISEUR
INDIVIDUEL DE TYPE
SPLIT
ȀȁǿȂǹȉǿȈȉǿȀǵ
ǻȍȂǹȉǿǵȊ
ǻǿǹǿȇǵȊȂǼȃǵȊ ȉȊȆǵȊ
CONDIZIONATORE
SPLIT PER AMBIENTI
ACONDICIONADOR
DE AIRE TIPO SPLIT
AR CONDICIONADO
DE SALA, TIPO SPLIT
INSTALLATION MANUAL
MANUEL D’INSTALLATION
ǼīȋǼǿȇǿǻǿǵǼīȀǹȉǹȈȉǹȈǾȈ
MANUALE PER
L’INSTALLAZIONE
MANUAL DE INSTALACIÓN
MANUAL DE INSTALAÇÃO
2
24
46
68
90
112
EN
FR
EL
IT
ES
PT

2
Table of Contents
Congratulations ......................................... 2
Safety Precautions .................................... 3
Notice for Installation ................................ 3
Before Installation
Tools needs for installation ...................... 4
Product Description ................................. 5
Installation site instruction ....................... 6
Pipe length elevation and additional
quantity of gas ......................................... 7
Outdoor unit installation .......................... 8
Installation
Installation of mounting plate .................. 8
Drill piping hole ........................................ 10
Installation of drain hose ......................... 10
Installation of indoor unit ......................... 11
Installation of connection pipe ................. 14
Piping connection-indoor unit .................. 15
Piping connection-outdoor unit ................ 16
Piping formation ...................................... 16
Electrical installation ................................ 17
Check the drainage ................................. 20
Air purging and leakage test ................... 21
Test and Running ....................................... 22
 Do not operate unit with horizontal louver is in
closed position.
 The indoor unit should be installed on the wall
at the height of 2.3 meters or more from the the
ÀRRU
 The indoor unit should be installed allowing a
minimum clearance of 15cm from the ceiling.
 Before obtaining access to terminals, allsupply
circuit must be disconnected.
Congratulations
Congratulations and thank you for choosing a split-
W\SHDLUFRQGLWLRQHU:HDUHVXUH\RXZLOO¿QG\RXU
new air conditioner a pleasure to use.
Before you use the air conditioner, we recommend
that you read through the entire user manual, which
provides the description of the air conditioner and
its functions.
To avoid the risks that are always present when
you use an electrical appliance, it is important that
the air conditioner is installed correctly and that
you read the safety instructions carefully to avoid
misuse and hazards.
We recommend that you keep this instruction
booklet for future reference and pass it on to any
future owners.
After unpacking the air conditioner please check
it is not damaged. If in doubt, do not use the air
conditioner but contact your local authrised service
centre.
Information on disposal for users
 Most of the packing materials are recyclable.
Please dispose of those materials through
your local recycling depot or by placing them in
appropriate collection containers.
 If you wish to discard this air conditioner, please
contact your local authorities and ask for the
correct method of disposal.
Conditions of use
This appliance is intended to be used in household
and similar applications such as:
 6WDIINLWFKHQDUHDVLQVKRSVRI¿FHVDQGRWKHU
working environments.
 Farm houses.
 By clients in hotels, motels, and other residential
type environments.
 Bed and breakfast type environments.
warning
environmental tip

3
Notice for Installation
1 The unit must only be installed by a qualified refrigeration mechanic and electrical work
carried out by a qualified electrician according to local or government regulations and in
compliance with this manual.
2 Before installation, please contact a qualified air conditioner installer. Otherwise, the
malfunction may not be solved due to faulty installation.
3 If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or
similarly qualified persons in order to avoid a hazard.
4 An all-pole disconnection switch having a contact separation of at least 3mm in all poles
should be connected in fixed wiring. For models with a power plug, make sure the plug is
within reach after installation.
5 The temperature of refrigerant circuit will be high, please keep the interconnection cable
away from the copper tube.
6 This appliance can be used by children aged from 8 years and above and persons with
reduced physical, sensory or mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of the appliance in a safe way and
understand the hazards involved. Children shall not play with the appliance. Cleaning and
user maintenance shall not be made by children without supervision.
7 If the unit is to be moved to another location or disposed of, only a suitably qualified person
is permitted to undertake such work.
8 Take care not to catch fingers on the fan blade when adjusting vertical louvers.
9 This air conditioner uses R22 or R410A refrigerant (Confirm before installation).
Safety precautions
Please ready this installation manual and the
user manual before installation and carefully
store in a handy place for later reference.
on how to use and maintain your air conditioner
properly.
Electrical work must be installed by a licensed
electrician. Be sure to use the correct rating of
the power plug and main circuit for the model to
be installed.
Incorrect installation due to ignoring this
instruction will cause harm or damage, and
indications.
Meanings of symbols used in this manual are
shown below:
This symbol indicates information concerning
your personal safety.
caution
warning
This indicates information concerning your
personal safetyand how to avoid damaging the
appliance.
This symbol indicates tips and information
about use of the appliance.
This symbol indicates tips and information
about economical and ecological use of the
appliance.
This symbol indicates never to do this.
Always do this.
caution
environmental tip
tips and information

4
Before Installation
Tools Needs for Installation
Items Required for Installion
1 Level gauge
2 Screw driver
3 Electric drill
4 Hole core drill ( 55mm / 70mm)
5 Flaring tool set
6 6SHFL¿HGWRUTXHZUHQFKHV
7 Spanner (half union)
8 A glass of water
9 +H[DJRQDOZUHQFKPP
10 Gas-leak detector
11 Vacuum pump
12 Gauge manifold
13 Users manual
14 Thermometer
15 Multimeter
16 Pipe cutter
17 Measuring tape
Note: Other necessary parts for the installation, besides the above mentioned, must be provided
by the customer/installer.
Number Name of Accessories Quantity
Indoor unit mounting plate 1
Clip anchor Not supplied
6HOIWDSSLQJVFUHZ67[ 5 or 10
Remote control 1
Remote control holder Not supplied
Screw for remote holder Not supplied
Battery (AAA 1.5V) 2
Insulation material Not supplied
Connection piping assembly (refer to page 6) Varies by country
Insulation hose for refrgerant piping Not supplied
Wall clamp Not supplied
Drain hose Not supplied
Connection power cable Not supplied
Drain connector (Heat Pump model only, page 7) 1
Drain plug (Heat Pump model with capcity of over 4500W) 3
7KHUPDOLQVXODWLQJSLSHIRUH[WHQGLQJGUDLQKRVH 1
Flare nut (for suction pipe) 1

5
Light
Turbo Healthy
Timer-On Temp
Timer-Off
Swing I feel Eco
Fan
Clock
Mode
5
15
16
17
15cm above
15cm above
Product Description
Space to the wall
Space to obstruction
30cm above
2m above
Air outlet side
Air inlet side
30cm above
50cm above
Space to the wall
Space to the ceiling
15cm above
Space to the wall
3m above
Air outlet side
Indoor
Unit Space to the wall
Outdoor
Unit
50cm above
NOTE: We suggest to install the indoor unit at height above of 230cm.

6
Installation Site Instruction
More than 30cm
More than 30cm
More than 2m
More than 50cm
More than 15cm (ceiling)
More than
15cm
More than
15cm
7 Select place about 1m or more away from a
TV set or any other electric appliance.
8 taken out.
9 Do not use the unit in the laundry or by
swimming pool etc.
10 A minimum pipe run of 3 meters is required to
minimize vibration and noise.
11 unnecessary damage to the wall.
12 Any variations in pipe length will/may require
adjustment to refrigerant charge.
13 Do not install near a door way.
Outoor Unit
1 emitted by unit will not annoy neighbors.
2 ventilation.
3 Select a site where there is no obstruction
blocking the inlet and outlet.
4 The site should be able to withstand the full
weight and vibration of the unit.
5 Select a dry place, but do not expose the unit
to direct sunlight or strong wind.
6 Make sure that the outdoor unit is installed in
accordance with the installation instructions,
and is convenient for maintenance and repair.
7 Select a place where it is out of reach of
children and far from animals or plants.
8 Select a place where the unit keeps the
horizontal and aligned position.
9 Select at a place that respects the minimum
distances around the outdoor unit as below:
A proper installation site is vital for correct and
Avoid the following sites where:
or volatile liquids are emitted.
high-frequency electro-magnetic waves are
generated by radio equipment, welders or
medical equipment.
salt-laden air prevails (such as close to
coastal areas).
the air is contaminated with industrial vapours
and oils.
the air contains sulphurous gas such as in hot
spring zones.
corrosion or poor air quality exists.
Indoor Unit
1 The air inlet and outlet should be away from
the obstructions. Ensure the air can be blown
through the whole room.
2 Select a site where the condensing water can
be easily drained out, and where it is easily
connected for the outdoor unit.
3 Select a place where it is out of reach of
children.
4 Select the place where the wall is strong
enough to withstand the full weight and
vibration of the unit.
5 Be sure to leave enough space to allow
access for routine maintenance.
For optimum performance, the indoor unit
should be installed on the wall at a height
6 Make sure that the indoor unit is installed in
accordance with installation dimension as
below:

7
Pipe Length Elevation and Additional Quantity of Gas
 The outdoor unit is charged with the
refrigerant for standard pipe length.
 When the connecting pipe length is longer
than standard length, additional refrigerant
should be added into the unit according
the above table through the service port on
3-way service valve on the outdoor unit.
 Please maintain the shortest distance (3 to 5
meters) and shortest misalignment possible
between the indoor and outdoor units.
 7KHPD[LPXPDOORZDQFHOHQJWKDQGKHLJKW
is based on reliability.
 ([FHHGLQJWKHPD[LPXPPD\FDXVHSRRU
performance or malfunction.
 When the level difference between indoor
DQGRXWGRRUXQLWVLVJUHDWHUWKDQPD[LPXP
height, or when the outdoor unit is installed
above the indoor unit, oil trap should be
installed every 5-7 meters.
Outdoor unit Outdoor unit
Maximum length
Maximum length
Indoor unit
Maximum height
Indoor unit
Oil trap
Rooftop Installation
1 If the outdoor unit is installed on a roof
structure, be sure to level the unit.
2 Ensure the roof structure and anchoring
method are adequate for the unit location.
3 If the outdoor unit is installed on roof
VWUXFWXUHVRUH[WHUQDOZDOOVWKLVPD\UHVXOWLQ
H[FHVVLYHQRLVHDQGYLEUDWLRQDQGPD\DOVR
be classed as non-serviceable installation.
Piping length under 5m Piping length 5m or more
Cool
Capacity (W) Suction Pipe Diameter Discharge Pipe Diameter Standard Length (m)
Maximum
Length (m) Maximum
Height (m) Additional
Refrigerant
(g/m)
2640 Ø6.35 mm (1/4”) Ø9.52 mm (3/8”) 5 15 5 15
3520 Ø6.35 mm (1/4”) Ø12.7mm(1/2”) 5 15 5 15
5270 Ø6.35 mm (1/4”) Ø12.7mm(1/2”) 5 20 10 15
6450 Ø6.35 mm (1/4”) Ø15.88mm(5/8”) 5 20 10 15
caution
Maximum height

8
Outdoor Unit Installation
Drain-water
hole
Drain
connecter
Chassis
Hose of inner dia. 16mm
(not provided)
Installation
Air inlet
Air inlet
Air outlet
If a suspended installation is needed,
the installation bracket must allow the
The wall where the unit will be installed
must be of solid brick, concrete or
provided with other reinforcement ways
bracket to the wall and the bracket to
and leveled.
existent in its based with 4 bolts and nuts of
10 mm tightly (not included).
Place the outdoor unit over a horizontal
concrete or rigid surface (never directly over
grass or land).
Step 2: Outdoor Condensate Drainage
(only for heat pump model)
During heating operation, the condensate and
defrosting water should be drained out reliably
through the drain hose.
Install the outdoor drain connector in the drain-
water hole on the chassis of outdoor unit, and
attach the drain hose to the connector so that
the waste water formed in the outdoor unit can
be drained out.
The drain-water hole must be plugged.
Whether to plug other holes will be determined
by the installer according to actual conditions.
In case of a drain hose, the unit must be
installed on a base more than 3cm height.
Step 1: Securing of Outdoor Unit
Step 1: Installation of Mounting Plate
1 Fit the mounting plate horizontally on the wall
ST4x25, item 3 on page 3).
2 Be sure that the mounting plate has been
Meanwhile, the weight should be evenly shared
by every screw.
3 If the wall is made of brick, concrete or the like,
the wall. Insert clip anchor (item 2 on page 3)
for appropriate mounting screws.
4 The water tray’s outlet for the indoor unit is two-
way drainage design. During installation, the
indoor unit should slightly slant to water tray’s
outlet for smooth drainage of condenser water.
Fit the mounting plate and drill holes in the wall
according to the wall structure and correcponding
mounting points on the mounting plate.
(dimensions are in mm unless otherwise stated)
Cool Capacity (W/h) Mounting Plate type
2640 A
3520 B
5270 C
6450 D
caution

40
40
40 78
36 605 149
265
9
45
Mark on the middle of it Gradienter
Space
to the
wall
150mm
above
Space
to the
wall
150mm
above
Wall Wall
Left
55mm Right
55mm
(Rear piping hole) (Rear piping hole)
Mounting Plate Type A
Mounting Plate Type B
Mounting Plate Type C
Mounting Plate Type D
542
43
43
143 80
131 172
ĭ ĭ
275
17
510
164
17 123
135
196
55 525
298
945
82 563
45
160
88
256
694
ĭ55
ĭ

10
Outlet pipe of
indoor unit
Vinyl tape
Outlet pipe of
indoor unit
Drain hose
Outlet pipe of
indoor unit Drain hose (narrow)
Vinyl tape Insulating pipe
Indoor
Wall pipe Seal putty
Outdoor
Ø55
or Ø70
5-10mm
Wall
Step 2: Drill Piping Hole
1 Determine hole positions according to the
GLDJUDP'ULOORQHKROHɎRUɎPP
in the wall at a slight downward slant to the
outdoor side.
Piping hole Model
ɎPP Cooling capacity <6000W
ɎPP Cooling capacity >6000W
2 The inclination must be between 5 - 10mm in
order to ensure a good drain of condensed
water generated by the indoor unit.
Step 3: Installation of Drain Hose
Remove both supports
3 Insert the wall pipe into the hole to prevent
and wiring from being damaged when passing
through the whole.
4 Always use a wall hole conduit when drilling
metal grids, metal plates or the like.
5 For cooling capacity over 4500W models,
remove and dispose the two polystyrene lateral
rear supports from the indoor unit before the
installation.
1 Connect the drain hose to the outlet pipe of the
indoor unit. Bind the joint with vinyl tape.
2 Put the drain hose into insulating pipe.
Connected
Vinyl tape
Insulating pipe
Outlet pipe of
indoor unit
3 Wrap the insulating pipe with wide vinyl tape
to prevent the shift of insulating pipe. Slant
the drain hose downward slightly for smooth
drainage of condensing water.