Electrolux EXP12EN1WI User manual

EXP12EN1WI
................................................ .............................................
EN PORTABLE AIR
CONDITIONER
USER MANUAL

Electrolux. Thinking of you.
Share more of our thinking at www.electrolux.com
CONTENTS
Safety information 2
Product description 4
Accessories 4
Installation 5
Control panel 9
Operating instructions 10
Care and cleaning 12
What to do if… 13
Environment concerns 14
Subject to change without notice.
SAFETY INFORMATION
Before use, carefully read the supplied in-
structions. The manufacturer is not respon-
sible if incorrect use causes injuries and
damages. Always keep the instructions for
future reference.
CHILDREN AND VULNERABLE
PEOPLE SAFETY
Warning! Risk of suffocation, injury or
permanent disability.
• Do not let persons, children included,
with reduced physical sensory, reduced
mental functions or lack of experience
and knowledge use the appliance. They
must have supervision or instruction for
the operation of the appliance by a per-
son who is responsible for their safety.
• Do not let children play with the appli-
ance.
• Keep all packaging away from children.
INSTALLATION
Warning! Risk of overheating, fire or
damage to the appliance.
• Only a qualified person must install this
appliance.
• The installation must be performed in ac-
cordance to the national wiring standards
(if applicable).
• Move or store the appliance in an upright
position.
• Remove all the packaging.
• Do not install or use a damaged appli-
ance.
•Donotinstalloruse the appliance where
the temperature is less than 0 °C.
• Obey the installation instruction supplied
with the appliance.
• Do not install the appliance where there
is direct sunlight.
• Be careful, when adjusting the horizontal
louvres. There is a risk of catching fingers
on the fan.
Electrical connection
Warning! Risk of fire and electrical
shock.
• Make sure the appliance is installed cor-
rectly. Loose and incorrect plug and
socket connections can make the termi-
nal become too hot.
• Always use a correctly installed shock-
proof socket.
• Do not use multi-plug adapters and ex-
tension cables.
• Make sure not to cause damage to the
electrical components. Contact the Serv-
ice or an electrician to change the electri-
cal components.
• The power cord must not touch hot sur-
faces of other appliances.
• Do not use the power cord near flamma-
bles gas or combustibles, such as gaso-
line, benzene, thinner, etc.
• Always install circuit breaker and a dedi-
cated power circuit.
• Connect the mains plug to the mains
socket only at the end of the installation.
Make sure that there is access to the
mains plug after the installation.
• Do not pull the mains cable to disconnect
the appliance. Always pull the mains
plug.
• Provide a residual current device (RCD).
• Make sure the power supply has an ap-
propriate voltage rating. Only use 220V
2 electrolux

— 240V, 50Hz, 10A mains electricity
supply.
• The appliance must be earthed.
• The appliance is equipped with a cord
having an earth wire connected to a
grounding tab (A). The plug must be
plugged into an outlet that is properly in-
stalled and earthed.
•ONLY FOR UK: The appliance is equip-
ped with a cord that has an earthed wire
connected to an earthed pin (B). The
plug must be plugged into a socket that
is properly installed and earthed. Do not
under any circumstances cut or remove
the square earthed pin(B). from the plug.
USE
Warning! Risk of injury, burns,
electrical shock or fire.
• Use this appliance in a household envi-
ronment.
• Do not change the specification of this
appliance.
• Do not direct the airflow at room occu-
pants, pets or hose plants.
• Ventilate the room before using the air
conditioner.
• Do not operate the appliance with wet
hands or when it has contact with water.
• Do not operate the appliance without the
air filter.
A
B
• Always drain the condensate before stor-
ing the appliance.
• Make sure the drain hose is not above
the drain fitting.
• Do not place obstacles around the air-in-
lets or inside of air-outlets.
• Do not operate or stop the appliance by
pulling out the power cord.
• Do not operate the appliance near any
heat source or open fire.
• Do not cover the appliance when in oper-
ation or immediately after use.
• Do not drink water drained from the ap-
pliance.
• If a burning smell or any other abnormali-
ty occurs, deactivate the appliance im-
mediately.
CARE AND CLEANING
Warning! Risk of injury or damage to
the appliance.
• Contact Service for maintenance or re-
pair of this appliance.
• Deactivate the appliance before cleaning.
• Before maintenance, deactivate the ap-
pliance and disconnect the mains plug
from the mains socket.
• When the air filter is to be removed, do
not touch the metal parts of this appli-
ance.
• Clean the filter once every two weeks. Al-
ways insert the filters securely.
• Do not use water spray and steam to
clean the appliance.
• Clean the appliance with a moist soft
cloth. Only use neutral detergents. Do
not use abrasive products, abrasive
cleaning pads, solvents or metal objects.
DISPOSAL
• Disconnect the appliance from the mains
supply.
• Cut off the mains cable and discard it.
• This appliance uses R410A refrigerant.
• If you wish to discard this product, please
contact your local authorities and ask for
the correct method of disposal.
electrolux 3

PRODUCT DESCRIPTION
UNIT DESCRIPTION
4
3
2
1 5
6
1
2
3
4
5
6
1CONTROL PANEL
2CARRYING HANDLE (BOTH SIDES)
3REMOTE CONTROL STORAGE DOOR
4REMOTE CONTROL
5ROOM AIR DISCHARGE
6CASTOR
1EXHAUST AIR OUTLET
2EXHAUST ADAPTOR A
3BOTTOM TRAY DRAIN OUTLET
4AIR INTAKE
5DEHUMIDIFYING DRAIN OUTLET
6EXHAUST HOSE (STORAGE WHEN
NOT IN USE)
ACCESSORIES
Check all the accessories are included
in the package and please refer to the
“Installation” chapter for their usage.
ABCD
EF G
HIJ
PART PART NAME QUANTITY
AExhaust hose 1 pc
BUnit/Exhaust Adaptor A 1 pc
4 electrolux

PART PART NAME QUANTITY
CWindow/Exhaust Adaptor B 1 pc
DWindow Sliding Kit 1 pc
EFoam Seal 3 pc
FRemote Control 1 pc
GBattery (for remote control) 2 pc
HWall Adaptor (for permanent duct mounting) 1 pc
IWall Plug 4 pc
JScrews 4 pc
INSTALLATION
EXHAUSTING HOT AIR
WINDOW DISCHARGE
In the COOLING mode (COOL) the appli-
ance must be placed close to a window so
that the warm exhaust air can be ducted
outside. First, place the unit on a flat floor
and make sure there’s a minimum of 30,5
cm clearance around the unit, and is within
the vicinity of a single circuit outlet power
source.
1. Take the hose out from back of the unit
2. Remove adaptor A from units by sliding
sideways.
3. Extend either side of the hose and
screw the hose to adaptor A.
electrolux 5

4. Extend the other side of the hose and
screw it to adaptor B.
5. Slide the assembly onto unit.
6. Affix the adaptor B into the window
slider kit and seal.
• Window slider kit:
Minimum: 67,5 cm (26,6 inches)
Maximum: 123 cm (48,5 inches)
Vertical window
Horizontal window
6 electrolux

WALL DISCHARGE
Mount wall adaptor directly over correctly
installed duct to outside. (This usually in-
cludes aluminium wall ducting and an out-
side cover. See your hardware specialist for
correct installation.)
Use wall pluges and screws to secure. At-
tach hose duct to wall adaptor.
max 48”
min 12”
The hose can be extended from its original
length of 38,1 cm up to 139,7 cm, but it is
the best to keep the length to minimum re-
quired. Also make sure that the hose does
not have any sharp bends or sags.
INSTALLATION IN A DOUBLE-HUNG
SASH WINDOW
1. Cut the foam seals - adhesive type (A)
to the proper lengths and attach them
to the window and stool.
A
2. Attach the window slider kit to the win-
dow stool. Adjust the length of the win-
dow slider kit according to the width of
window. Cut the adjustable window
slider kit if the width of window is less
than 67,5 cm.
3. Open the window sash and place the
window slider kit (B) on the window
stool (C).
675-1230
B
C
electrolux 7

4. Close the window sash securely
against the window slider kit.
5. Cut the foam seals to an appropriate
length and seal the open gap between
the top window sash and outer window
sash, as shown.
INSTALLATION IN A SLIDING SASH
WINDOW
1. Cut the foam seals-adhesive type (A) to
the proper lengths and attach them to
the window and stool.
A
2. Attach the window slider kit to the win-
dow stool. Adjust the length of the win-
dow slider kit according to the height of
window. Cut the adjustable window
slider kit if the height of window is less
than 67,5 cm.
3. Open the window sash and place the
window slider kit (B) on the window
stool (C).
4. Close the sliding sash securely against
the window slider kit.
5. Cut the foam seals to an appropriate
length and seal the open gap between
the sliding sash and outer window
sash, as shown.
675-1230
BC
8 electrolux

CONTROL PANEL
CONTROL PANEL
1 2 3 4 5
678910
1CHECK FILTER RESET BUTTON
2DISPLAYS TEMPERATURE/TIME
3TURNS UNIT ON OR OFF
4REMOTE SIGNAL RECEIVER
5SWING BUTTON (SWING)
6ACTIVATES TIMER (TIMER)
7SET MODE (MODE)
8ADJUSTS TEMPERATURE OR TIME
9SETS FAN SPEED (FAN SPEED)
10 SLEEP MODE (SLEEP)
REMOTE CONTROL
10
9
7
3
4
6
8
1
5
2
1MODE INDICATION
2TEMPERATURE/TIMER CONTROL
BUTTONS
3MODE SELECTOR (MODE)
4SLEEP BUTTON
(SLEEP)
5RESET+LOCK PIN BUTTONS (RESET/
LOCK)
6FAN SPEED SELECTION
7FAN SPEED SELECTOR (FAN SPEED)
8TIMER BUTTONS (TIMER ON/TIMER
OFF)
9SWING BUTTON (SWING)
10 ON/OFF BUTTON
BATTERY SIZE: AAA
Warning! Do not mix old and new
batteries. Do not mix alkaline, standard
(carbon-zinc) or rechargeable (nickel-
cadmium) batteries.
The Reset button RESET is depressed
when you want to return to the initial factory
settings. The Lock button LOCK is de-
pressed to lock the keypad so the settings
cannot be changed. The key symbol will
electrolux 9

appear in the display of the remote control;
depress the Lock button LOCK again to re-
lease. Use a small pin to depress these but-
tons.
OPERATING INSTRUCTIONS
Important! The following instructions
represent the Control Panel. The same
instructions can be used for the Remote
Control.
COOLING MODE (COOL)
In this mode the exhaust adaptor hose
MUST be used.
1. Press the Mode button (MODE) until
the Cooling (COOL) indicator lights.
2. Press Temperature buttons for
desired setting.
3. Press the Fan button (FAN SPEED) for
desired fan speed.
HEATING MODE (HEAT) (ON SOME
MODELS)
In this mode you do not need to use the
exhaust adaptor hose.
1. Press the Mode button (MODE) until
the Heating (HEAT) indicator lights.
2. Press the Temperature buttons
for the desired heat setting.
DRY MODE (DRY)
In this mode you do not need to use the
exhaust adaptor hose, BUT the water
collected must be discharged. See
“Drainage” section.
1. Press the Mode button (MODE) until
the Dry (DRY) indicator lights.
2. The fan will run at low speed and the
display will show the room tempera-
ture.
3. Keep doors and windows closed for
best effect.
AUTO MODE (AUTO)
Always have the exhaust hose attached
in this mode.
When you set the air conditioner in Auto
mode (AUTO), it will automatically select
cooling, heating (inapplicable for cooling
only models) or fan only operation, depend-
ing on what temperature you have selected
and the room temperature. The air condi-
tioner will control room temperature auto-
matically round the temperature point set
by you. Under Auto mode (AUTO) you can
not select the fan speed.
FAN MODE (FAN)
In this mode there is no need to use the ex-
haust hose or drainage hose. However, if
you require stale or smoky air to be re-
moved from the room, hook up the duct
accessories as described in the "Exhaust-
ing hot Air" section.
1. Press the Mode button (MODE) until
the Fan (FAN) indicator lights
2. Press the Fan (FAN SPEED) button to
choose the desired fan speed.
3. The fan will run at the selected speed
and the display will show the room
temperature.
TIMER OPERATION (TIMER)
You can set both delay stop and delay start
while unit is in ON position or OFF position.
When unit is in ON position, first press the
Timer button (TIMER) to go to delay stop
setting, then timer off (TIMER OFF) light will
illuminate. Tap or hold the up arrow or
the down arrow to change delay stop
timer at 0,5 hour increments up to 10
hours, then at 1 hour increments up to 24
hours. Then press the Timer button (TIMER)
to confirm the setting (the control will con-
firm the setting automatically after 5 sec-
onds) and go to delay start setting.
Use the same way as above to set the de-
lay start timing. If you don’t need to set de-
lay start, press the Timer button (TIMER)
again to exit. After 5 second the control will
automatically change the display back to
previous temperature display. If you want to
check remain timing, press the Timer but-
ton(TIMER). The delay start operation auto-
matically selects mode, temperature and
fan speed the same as last operation you
set.
When unit is in OFF position, press the Tim-
er button (TIMER) to go to delay start set-
ting, then timer on (TIMER ON) light will illu-
minate. Set the delay start and delay stop
timing the same way as above.
10 electrolux