Electrolux EKM55402X User manual

OPERATING AND INSTALLATION
INSTRUCTIONS OF
FREESTANDING GAS COOKER
EKM55402X
EN

Dear Customer,
Our goal is to offer you products with high quality that exceed your expectations.
Your appliance is produced in modern facilities carefully and particularly tested for
quality.
This manual is prepared in order to help you use your appliance that is manufactured
by the most recent technology, with confidence and maximum efficiency.
Before using your appliance, carefully read this guide that includes the basic
information for right and safe installation, maintenance and use. Please contact to
the nearest Authorized Service for the installation of your product.

2
CONTENTS:
1. BRIEF PRESENTATION OF PRODUCT
2. WARNINGS
3. INSTALLATION AND PREPARATIONS FOR USE
3.1 Environment where the appliance to be installed
3.2 Installation of product
3.3 Adjustment of feet
3.4 Gas connection
3.5 Electric connection and safety
3.6 Gas conversion
4. USE OF YOUR PRODUCT
4.1 Use of gas burners
4.1.1 Control of hob burners
4.1.2 Use of hotplate
4.1.3 Control of oven burner
4.1.4 Control of grill burner
4.2 Accessories used in oven
5. CLEANING AND MAINTENANCE
5.1 Cleaning
5.2 Maintenance
6. SERVICE AND TRANSPORT
6.1
6.2 Information related to the transport
Basic troubleshooting before contacting service

3
11
12
13
14
15
1. BRIEF PRESENTATION OF PRODUCT
List of Components:
1- Lid
2- Cooktop
3- Control Panel
4- Oven Door Handle
5- Adjustable Feet
6- Oven Door
7- Oven Tray
8- Wire Grid
9- Grill Burner
10- Oven Lamp
11- Electrical Hotplate
12- Rapid Burner
13- Auxillary Burner
14- Pan Support
15- Semi-Rapid Burner
9
10
1
2
3
45
6
7
8
MODEL DEPTH WIDTH HEIGHT
(cm) (cm) (cm)
EKM55402X 50 50 85

4
2. WARNINGS
READ THESE INSTRUCTIONS CAREFULLY AND COMPLETELY BEFORE USING YOUR APPLIANCE, AND KEEP IT IN A
CONVENIENT PLACE FOR REFERENCE WHEN NECESSARY.
THIS MANUAL IS PREPARED FOR MORE THAN ONE MODEL IN COMMON. YOUR APPLIANCE MAY NOT HAVE
SOME OF THE FEATURES THAT ARE EXPLAINED IN THIS MANUAL. PAY ATTENTION TO THE EXPRESSIONS THAT
HAVE FIGURES, WHILE YOU ARE READING THE OPERATING MANUAL.
General Safety Warnings
- This appliance can be used by children aged from 8
years and above and persons with reduced physical,
sensory or mental capabilities or lack of experience
and knowledge if they have been given supervision
or instruction concerning use of the appliance in a
safe way and understand the hazards involved.
Children shall not play with the appliance. Cleaning
and user maintenance shall not be made by children
without supervision.
- WARNING: The appliance and its accessible parts
become hot during use. Care should be taken to
avoid touching heating elements. Children less than
8 years of age shall be kept away unless
continuously supervised.
- WARNING: Unattended cooking on a hob with fat
or oil can be dangerous and may result in fire.
NEVER try to extinguish a fire with water, but switch
off the appliance and then cover flame e.g. with a
lid or a fire blanket.
- WARNING: Danger of fire: do not store items on
the cooking surfaces.

5
2. WARNINGS
- WARNING: If the surface is cracked, switch off the
appliance to avoid the possibility of electric shock.
- For hobs incorporating a lid, any spillage should be
removed from the lid before opening. And also the
hob surface should be allowed to cool before closing
the lid.
- The appliance is not intended to be operated by
means of an external timer or separate remote-
control system.
- WARNING: In order to prevent tipping of the
appliance, the stabilizing brackets must be installed.
(For detail information please read the anti-tilting kit
set guide.)
- During use, the appliance becomes hot. Care
should be taken to avoid touching heating elements
inside the oven.
- During use, handles held for short periods in
normal use can get hot.
- Do not use harsh abrasive cleaners or sharp metal
scrapers to clean the oven door glass and other
surface since they can scratch the surface, which
may result in shattering of the glass or damage to
the surface.
- Do not use steam cleaners for cleaning the
appliance.

6
1. SAFETY WARNINGS
- WARNING: Ensure that the appliance is switched
off before replacing the lamp to avoid the possibility
of electric shock.
- CAUTION: Accessible parts may be hot when the
cooking or grilling is in use. Young children should be
kept away.
- Your appliance is produced in accordance with all applicable local and international standards and
regulations.
- Maintenance and repair work must be made only by authorized service technicians. Installation
and repair work that is carried out by unauthorized technicians may endanger you. It is dangerous
to alter or modify the specifications of the appliance in any way.
- Prior to installation, ensure that the local distribution conditions (nature of the gas and gas
pressure or electricity voltage and frequency) and the requirements of the appliance are
compatible. The requirements for this appliance are stated on the label.
- CAUTION: This appliance is designed only for cooking food and is intended for indoor domestic
household use only and should not be used for any other purpose or in any other application,
such as for non-domestic use or in a commercial environment or room heating.
- Do not try to lift or move the appliance by pulling the door handle.
- This appliance is not connected to a combustion products evacuation device. It shall be installed
and connected in accordance with current installation regulations. Particular attention shall be
given to the relevant requirements regarding ventilation.
- If after 15 s the burner has not lit, stop operating the device and open the compartment door
and/or wait at least 1 min before attempting a further ignition of the burner.
- These instructions are only valid if the country symbol appears on the appliance. If the symbol
does not appear on the appliance, it is necessary to refer to the technical instructions which will
provide the necessary instructions concerning modification of the appliance to the conditions of
use of the country.
- All possible security measures have been taken to ensure your safety. Since the glass may break,
you should be careful while cleaning to avoid scratching. Avoid hitting or knocking on the glass
with accessories.
- Ensure that the supply cord is not wedged during the installation. If the supply cord is damaged,
it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to
prevent a hazard.
- While the oven door is open, do not let children climb on the door or sit on it.
Installation Warnings
- Do not operate the appliance before it is fully installed.
- The appliance must be installed by an authorized technician and put into use. The producer is
notresponsible for any damage that might be caused by defective placement and installation by
unauthorized people.

7
1. SAFETY WARNINGS
- When you unpack the appliance, make sure that it is not damaged during transportation. In case
of any defect; do not use the appliance and contact a qualified service agent immediately. As the
materials used for packaging (nylon, staplers, styrofoam...etc) may cause harmful effects to
children, they should be collected and removed immediately.
- Protect your appliance against atmospheric effects. Do not expose it to effects such as sun, rain,
snow etc.
- The surrounding materials of the appliance (cabinet) must be able to withstand a temperature of
min 100°C.
During usage
- When you first run your oven a certain smell will emanate from the insulation materials and the
heater elements. For this reason, before using your oven, run it empty at maximum temperature
for 45 minutes. At the same time you need to properly ventilate the environment in which the
product is installed.
- During usage, the outer and inner surfaces of the oven get hot. While opening the oven door,
step back to avoid the hot steam coming out of the oven. There may be a risk of burns.
- Do not put flammable or combustible materials, in or near the appliance when it is operating.
- Always use oven gloves to remove and replace food in the oven.
- Do not leave the cooker while cooking with solid or liquid oils. They may catch fire on condition of
extreme heating. Never pour water on to flames that are caused by oil. Cover the saucepan or frypan
with its cover in order to choke the flame that has occured in this case and turn the cooker off.
- Always position pans over the centre of the cooking zone, and turn the handles to a safe position so
they cannot be knocked or grabbed.
- If you will not use the appliance for a long time, plug it off. Keep the main control switch off. Also
when you do not use the appliance, keep the gas valve off.
- Make sure the appliance control knobs are always in the "0" (stop) position when it is not used.
- The trays incline when pulled out. Be careful not to let hot liquid spill over.
- CAUTION: The use of a gas cooking appliance results in the production of heat, moisture and
products of combustion in the room in which it is installed. Ensure that the kitchen is well ventilated
especially when the appliance is in use, keep natural ventilation holes open or install a mechanical
ventilation device (mechanical extractor hood).
- Prolonged intensive use of the appliance may call for additional ventilation, for example opening
of a window, or more effective ventilation, for example increasing the level of mechanical
ventilation where present.
- While using the grill burner, keep the oven door open and always use the grill deflector shield
supplied with the product. Never use the grill burner with the oven door closed.
- CAUTION: Glass lids may shatter when heated.
Turn off all the burners before shutting the lid.
The hob surface should be allowed to cool before closing the lid.
- When the door or drawer of the oven is open, do not leave anything on it. You may unbalance
your appliance or break the cover.
- Do not put heavy things or flammable or ignitable goods (nylon, plastic bag, paper, cloth...etc)
into the drawer. This includes cookware with plastic accessories (e.g. handles).
- Do not hang towels, dishcloths or clothes from the appliance or its handles.

8
1. SAFETY WARNINGS
During cleaning and maintenance
- Always turn the appliance off before operations such as cleaning or maintenance. You can do it
after plugging the appliance off or turning the main switches off.- Do not remove the control
knobs to clean the control panel.
TO MAINTAIN THE EFFICIENCY AND SAFETY OF YOUR APPLIANCE, WE RECOMMEND YOU ALWAYS
USE ORIGINAL SPARE PARTS AND TO CALL ONLY OUR AUTHORIZED
SERVICE AGENTS IN CASE OF NEED.

9
3. INSTALLATION AND PREPARATIONS FOR USE
This modern, functional and practical cooker, that was manufactured with the parts and materials of
highest quality, will meet your cooking needs in every aspect. You must surely read this manual so
that you don't have any problem in future and to be able to have satisfactory results. The following
information are the required rules for right installation and service processes. It must be read
especially by the technician who will install the appliance
Contact to Authorized Service for installation of your product
Your product must be set up and used in a place where it will always have ventilation
While operating, this appliance needs
There must be a natural ventilation enough to provide the gas to be used in the environment.
The average air flow must directly come in through the air holes that will be opened on the walls
that are opened towards outside.
.
3.1 Environment where your appliance will be installed
• .
3
• 2m /h air per kw input.
•
•
.
2
These air holes must have at least the effective cross section of 100cm for fresh air circulation
(One or more air holes can be opened.). This hole (or holes) must be opened so that they are not
blocked. Preferably they must be placed close to the bottom and at opposite side of the smokes
of the burned gases that were emptied. If it seems not possible to open these ventilations in the
place where the appliance is set up, the needed air can also be obtained through the next room,
provided that this place is not a bedroom or a dangerous place. In this case this “next room”
must also be ventilated as required.
Emptying of the Burned Gases from Environment
The cooking appliances that operate with gas, throw the burned gas wastes out directly to the
outside or through the cooker hoods that are connected to the a chimney that opens directly to the
outside. If it seems not possible to install a cooker hood, it is required to set an electric fan on the
window or wall that has access to fresh air. This electric fan must have the capacity to change the air
of the kitchen environment 4-5 times of its own volume of air per hour
!
Air inlet section
2
min. 100cm
Air inlet section
2
min. 100cm
Figure 1 Figure 2

10
3. INSTALLATION AND PREPARATIONS FOR USE
Cooker hood
flue Electrical ventilator
Air inlet section
2
min. 100cm
Air inlet section
2
min. 100cm
Figure 3 Figure 4
3.2 Installation of product
.
•
.
•
.
• .
• 80°C.
•
There are some factors that must be paid attention to while installing your product. Surely be very
careful to while installing your product. Pay attention to our below instructions in order to be able
to prevent any problems and/or dangerous situations that may occur later
The appliance can be placed close to other furniture on condition that in the area where the
oven is set up, the furniture's height does not exceed the height of the cooker panel
Pay attention not to place it near the refrigerator, there must be no flammable or inflammable
materials such as curtain, waterproof cloth, etc. that will begin to burn quickly
It is required that there must be least a 2cm blank space around the product for air circulation
The furniture close to product must be manufactured resistant to temperatures up to
If the kitchen furniture are higher than the cooktop, it must be at least 10cm away from the
cooker's side.
The minimum heights from the pan support and wall cupboards to cooker hoods with fan over the
product, are shown in figure 5. Thus, the cooker hood must be at minimum 65cm height from the
pan support. If there is no cooker hood, this height must not be less than 70cm.
Figure 5
Min. 50cm
COOKER HOOD
Min. 42cm
Min. 42cm
Min. 65cm(with hood)
Min. 70cm(without hood)

3. INSTALLATION AND PREPARATIONS FOR USE
11
3.3 Adjustment of feet
.
3.4 Gas connection
Your stands on 4 adjustable feet. When the is
placed where to be used, check if the product is balanced. If it
is not balanced, you can make the adjustment by turning the
feet clockwise if required. It is possible to raise the appliance
maximum 30mm by the feet. If the feet are adjusted
appropriately, it is required not to move the appliance by
dragging, it should be moved by lifting it up
Assembly of gas supply and leakage check
The connection of the appliance should be performed in accordance with local and international
standards and regulations applicable. You can find the information related to appropriate gas types
and appropriate gas injectors on technical data table. If the pressure of used gas is different than
these values stated or not stable in your area, it may be required to assemble an available pressure
regulator on the gas inlet. It is certainly required to contact to the authorized service to make these
adjusments.
The points that must be checked during flexible hose assembly
If the gas connection is made by a flexible hose that is fixed on the gas inlet of appliance, it must be
fixed by a pipe collar as well. Connect your appliance with a short and durable hose that is as close
as possible to the gas source. The hose's permitted maximum lenght is 1.5m. The hose that brings
gas to the appliance must be changed once a year for your safety.
0
The hose must be kept clear from areas that may heat up to temperatures in excess of 50 C. The
hose must not be ruptured, bent or folded. It must be kept clear of sharp corners, moving things,
and should not be defective. Before assembly, it must be checked whether there is any production
defect.
As gas is turned on, all connection parts and hose must be checked with soapy water or leakage
fluids. Do not use naked flame to check gas leakage. All metal components used during gas
connection must be clear of rust. Also check the expiry dates of components to be used.
The points that must be checked during fixed gas connection assembly
To assemble a fixed gas connection (gas connection made by threads, e.g. a nut), there are different
methods used in different countries. The most common parts are already supplied with your appliance.
Any other part can be supplied as spare part.
During connections always keep the nut on the gas manifold fixed, while rotating the counter-part. Use
spanners of appropriate size for safe connection. For all surfaces between different components,
product product
Figure 6

3. INSTALLATION AND PREPARATIONS FOR USE
12
always use the seals provided in the gas conversion kit. The seals used during connection should
also be approved to be used in gas connections. Do not use plumbing seals for gas connections.
Remember that this appliance is ready to be connected to gas supply in the country for which it has
been produced. The main country of destination is marked on the rear cover of the appliance. If you
need to use it in another country, any of the connections in the figure below can be required. In
such a case, learn the appropriate connection parts and obtain those parts to perform a safe
connection.
It is required to call the authorized service to be able to make the gas connections appropriately
and in compliance with safety standards.
Surely do not use any match or lighter for control of gas leakage
During the electric connection, follow the instructions stated in the user manual
The earthing cable must be connected to the earth terminal
You have to ensure the power cord with suitable insulation to be connected to the power source
during the connection If there is no appropriate earthed electric outlet in accordance with
regulations in the place where the appliance to be installed, contact to our authorized service.
The earthed electric outlet must be close to the appliance.
Do not use an extension cord
The power cord must not touch to the hot surface of the product.
In case the cord is damaged, contact Authorized Service to have it changed
Any wrong electric connection may damage your appliance, as well as endangering your safety,
rendering your guarantee invalid
ATTENTION! .
3.5 Electric connection and safety
.
• .
•
.
• .
•
• .
•
.
!
Seal
Seal
Seal
Hose
Fitting
Adaptor
Gas Hose
with Collar
Mechanical
Gas Hose
Mechanical
Gas Hose
Mechanical
Gas Hose
Gas Pipe Gas
Pipe
Gas
Pipe
Gas
Pipe
Figure 7

13
•
.
The appliance is adjusted for 230V 50Hz electricity. If the mains electricity is different contact
your authorized service
L
N
BROWN
YELLOW+GREEN
BLUE
Figure 8
•
•
.
3.6 Gas conversion
:
Changing injectors:
:
• .
•
•
•
The supply cord should be kept away from hot parts of appliance. Otherwise, the cord may be
damaged, causing short circuit.
The manufacturer declares that it has no responsibility against any kind of damages and losses
that are caused by improper connections that are performed by unauthorized people
Caution : The following procedures must be undertaken by authorized service people.
Your appliance is adjusted to be operated with LPG/NG gas. The gas burners can be adapted to
different types of gas, by replacing the corresponding injectors and adjusting minimum flame length
suitable to the gas in use. For this purpose, following steps should be performed
Hob Burners
Cut off the main gas supply and unplug from the electric mains
Remove the burner cap and the adapter(Figure 9).
Unscrew the injectors. For this, use a 7mm spanner(Figure 10).
Replace the injector with the ones from the gas conversion kit, with corresponding diameters
suitable to the type of gas that is going to be used, according to the information chart (which is
also supplied in the gas conversion kit).
3. INSTALLATION AND PREPARATIONS FOR USE

14
Oven/Grill Injectors
The oven and grill injectors are assembled by a single screw that is placed on the tip of the burner.
For grill burners, this screw is already visible(Figure 11). Remove the screw, pull the grill burner to
yourself and you will see the injector revealed on the rear surface of the oven cavity (Figure 12).
For oven burners, open the drawer compartment and you will see the assembly screw below the
burner (Figure 13). Remove the screw, move the burner diagonally and the injector will be revealed on
the rear side of the burner box (Figure 12).
Remove the injectors with a 7mm spanner and replace the injector with the ones from the spare
set, with corresponding diameters suitable to the type of gas that is going to be used, according to
the information chart (which is also supplied in the gas conversion kit).
:
Adjusting the reduced flame position
The flame length in the minimum position is adjusted with a flat screw located on the valve. For
valves without flame failure device, the screw is located inside the valve spindle(Figure 14). For
easier reduced flame adjustment, it is advised to remove the control panel (and microswitch, if
present) during adjustment.
:
3. INSTALLATION AND PREPARATIONS FOR USE
Figure 10
Injector
Spanner
Figure 12
Figure 11
Screw
Figure 13
Screw
Injector
Figure 9

3. INSTALLATION AND PREPARATIONS FOR USE
15
To determine the minimum position, ignite the burners and leave them on in minimum position.
Remove the with the help of a small screwdriver fasten or loosen the bypass screw around 90
angular degrees. When the flame has a length of at least 4mm, the gas is well distributed. Make
sure that the flame does not die out when passing from the maximum position to the minimum
position. Create an artificial wind with your hand toward the flame to see if the flames are stable.
For oven burner, operate the oven burner at minimum position for 5 minutes, then open and close
the oven door for 2-3 times to check the flame stability of the burner.
Reduced flame position adjustment is not required for grill burners.
The position the bypass screw must be loosened for conversion from LPG to NG. For conversion
from NG to LPG, the same screw must be fastened. Make sure that the appliance is unpluged from
the electric mains and the gas supply is open.
Changing the gas inlet:
For some countries, the gas inlet type can be different for NG/LPG gases. In such a case, remove the
current connection components and nuts (if any) and connect the new gas supply accordingly. In all
conditions, all components used in gas connections should be approved by local and/or
international authorities. In all gas connections, refer to the “Assembly of gas supply and leakage
check” clause explained before.
Figure 14
Screw(inside the hole)
Valve without flame failure device
Figure 15
Bypass Screw
Thermostatic oven valve

4. USE OF YOUR PRODUCT
16
4.1 Use of gas burners
•
:
•
Ignition of the burners
To determine which knob controls which burner, check the position symbol above the knob.
Manual Ignition of the Gas Burners
If your appliance is not equipped with any ignition aid or in case there is a failure in the electric
network, follow the procedures listed below
For Hob Burners: To ignite one of the burners, press and turn its knob counter-clockwise so that the
knob is in maximum position, approach a match, taper or another manual aid to its upper
circumference. Move the ignition source away as soon as you see a stable flame.
For Oven Burner: To ignite the oven burner, press and turn the oven control knob counter-clockwise so
that the knob is in maximum position, approach a match, taper or another manual aid to the ignition
hole that is located on the front left corner of the burner. Move the ignition source away as soon as you
see a stable flame.
For Grill Burner: To ignite the grill burner, turn the grill valve in the clockwise position until the marker
on the knob points at the grill sign. Then, keep the knob pressed and approach a match, taper or
another manual aid to the holes that are situated on the burner. Move the ignition source away as soon
as you see a stable flame.
Electrical Ignition
Ignition by Spark Button: Press the valve of the burner you want to
operate and turn the valve in the counter-clockwise direction so that the
knob is in maximum position and with your other hand, press the ignition
button (Figure 16) at the same time. Press the ignition button
immediately, because if you wait, a build up of gas may cause the flame to
spread. Continue pressing the ignition button until you see a stable flame
on the burner.
Figure 16

4. USE OF YOUR PRODUCT
17
Flame safety device:
Oven / Grill Burners
.
4.1.1 Controlof the hob burners
Regardless of the model of your appliance, all oven burners are equipped with a gas safety device.
For this reason, during ignition, keep the oven knob pressed until you see stable flames. If the
flames are cut out after you release the knob, repeat the procedure again. If the oven burner does
not ignite after you keep the burner knob pressed for 30 seconds, open the oven door and do not
attempt re-ignition for at least 90 seconds. When oven flames go out accidentally, repeat the same
procedure
The knob has 3 positions: Off (0), maximum (big flame symbol) and minimum (small flame symbol).
After you ignite the burner in maximum position; you can adjust the flame length between
maximum and min. positions. Do not operate the burners when the knob position is between
maximum and off positions.
After the ignition, check the flames visually. If you see yellow
tip, lifted or unstable flames; turn the gas flow off, and check
the assembly of burner caps and crowns (Figure 18). Also,
make sure that no liquid has flown into the burner cups. If
the burner flame goes out accidentally, turn the burner off,
ventilate the kitchen with fresh air, and do not attempt re-
ignition for 90 sec.
When turning the hob off, turn the knob in the clockwise
direction so that the knob shows "0" position or the marker
on the knob points upwards.
Figure 18
Cap
Crown
Spark
Plug
Burner
Cup
MAX. position
OFF position
Figure 17
MODULATE
MIN. position

4. USE OF YOUR PRODUCT
18
Your hob has burners of different diameters. The most economic way of using gas is to choose the
correct size gas burners for your cooking pan size and to bring the flame to minimum position once
the boiling point is reached. It is recommended to always cover your cooking pan.
In order to obtain maximum performance from the main burners, use pots with the following flat
bottom diameters. Using smaller pots than the minimum dimensions stated below will cause
energy loss.
Rapid Burner: 22-26cm
Semi-rapid Burner: 14-22cm
Auxiliary Burner: 12-18cm
Make sure that the tips of the flames do not spread out of the outer circumference of the pan, as
this may also harm the plastic accessories around the pan (handles etc.).
When the burners are not in use for prolonged periods, always turn the main gas control valve off .
WARNING:
• Use only flat pans and with a sufficiently thick base.
• Ensure that the base of the pan is dry before placing it on the burners.
• The temperature of accessible parts may be high when the appliance is operating. So it is
imperative to keep children and animals out of the reach of the burners during and after
cooking.
• After use, the hob remains very hot for a prolonged period of time, do not touch it and do not
place any object on top of the hob.
• Never place knives, forks, spoons and lids on the hob as they will get hot and could cause
serious burns.
Figure 19
!

4. USE OF YOUR PRODUCT
19
4.1.2. Use of Hotplate
These hotplates are controlled by a 6 position switch.
By switching the control knob to one of these positions the
hotplate can be operated. Near each hob control knob, there is
a small diagram that shows which hotplate is controlled with
that knob. On/off light on the control panel shows if any of the
hotplates are in use.
Figure 20
Hotplate Knob Position - Function
0 Off position
1 To melt butter etc. and to warm small quantities of liquid.
2 To warm bigger quantities of liquid. To prepare creams and sauces.
3 To defrost food for cooking
4 To cook delicate meat and fish
5 To roast meat and steak
6 To boil big quantities of liquid or to fry.
Warning:
When the operating for the first time or whenever the hotplate has not been used for a prolonged
time it is necessary to eliminate any humidity which may have accumulated around the electrical
elements of the plate by operating the hotplate on its lowest setting for about 20 minutes.
Use only flat pans and with a sufficiently thick base.
Never use a pan with a smaller diameter than of the hotplate.
Ensure that the base of the pan is dry before placing it on the hotplate. While the hotplate is in
operation, it is important to ensure that the pan is centered correctly above the hotplate.
•
•
•
!