Electrolux EFP60032 User manual

USER MANUAL
EFP60032

We were thinking of you
when we made this product

electrolux 3
RECOMMENDATIONS AND SUGGESTIONS 4
CHARACTERISTICS 5
INSTALLATION 6
USE 8
MAINTENANCE 9
EN
Welcome to the world of Electrolux
Thank you for choosing a first class
product from Electrolux, which hopeful-
ly will provide you with lots of pleasure
in the future. The Electrolux ambition is
to offer a wide variety of quality prod-
ucts that make your life more comfort-
able. You find some examples on the
cover in this manual. Please take a few
minutes to study this manual so that
you can take advantage of the benefits
of your new machine. We promise that
it will provide a superior User Experi-
ence delivering Ease-of-Mind.
Good luck!
EN

4 electrolux Recommendations and Suggestions
EN
Installation
• The manufacturer will not be held li-
able for any damages resulting from
incorrect or improper installation.
• The minimum safety distance be-
tween the cooker top and the extrac-
tor hood is 650 mm.
• Check that the mains voltage corre-
sponds to that indicated on the rating
plate fixed to the inside of the hood.
• For Class I appliances, check that the
domestic power supply guarantees
adequate earthing.
Connect the extractor to the exhaust
flue through a pipe of minimum diam-
eter 120 mm. The route of the flue
must be as short as possible.
• Do not connect the extractor hood to
exhaust ducts carrying combustion
fumes (boilers, fireplaces, etc.).
• If the extractor is used in conjunction
with non-electrical appliances (e.g.
gas burning appliances), a sufficient
degree of aeration must be guaran-
teed in the room in order to prevent
the backflow of exhaust gas. The
kitchen must have an opening com-
municating directly with the open air in
order to guarantee the entry of clean
air.
Use
• The extractor hood has been de-
signed exclusively for domestic use to
eliminate kitchen smells.
• Never use the hood for purposes
other than for which it has ben de-
signed.
• Never leave high naked flames under
the hood when it is in operation.
• Adjust the flame intensity to direct it
onto the bottom of the pan only, mak-
ing sure that it does not engulf the
sides.
• Deep fat fryers must be continuously
monitored during use: overheated oil
can burst into flames.
• Do not flambè under the range hood;
risk of fire
• The hood should not be used by chil-
dren or persons not instructed in its
correct use.
Maintenance
• Switch off or unplug the appliance
from the mains supply before carrying
out any maintenance work.
• Clean and/or replace the Filters after
the specified time period.
• Clean the hood using a damp cloth
and a neutral liquid detergent.
The symbol on the product or on its
packaging indicates that this product may
not be treated as household waste. Instead
it shall be handed over to the applicable
collection point for the recycling of electrical
and electronic equipment. By ensuring this
product is disposed of correctly, you will help
prevent potential negative consequences for
the environment and human health, which
could otherwise be caused by inappropriate
waste handling of this product. For more
detailed information about recycling of this
product, please contact your local city office,
your household waste disposal service or
the shop where you purchased the product.
RECOMMENDATIONS AND SUGGESTIONS

Characteristics electrolux 5
EN
Dimensions
CHARACTERISTICS
0÷152
280
598 - 898
175
ø 120
Components
Ref. Q.ty Product Components
11 Hood Body, with: Controls, Light,
Blower, Filters
81 Directional Air Outlet grille
10 1 Adapting ring ø 120-125 mm
20 1 Closing Element
Ref. Q.ty Installation Components
12a 4 Screws 4,2 x 44,4
12e 2 Screws 2,9 x 9,5
Q.ty Documentation
1 Instruction Manual
1
12a
20
12e
8
10

6 electrolux Installation
EN
INSTALLATION
Drilling the Support surface and
Fitting the Hood
SCREW FITTING
• The hood support surface must be
135 mm above the bottom surface of
the wall units.
• Drill the support with a ø 4,5 mm drill
bit, using the drilling template pro-
vided.
• Cut a hole ø 125 mm in size on the
support surface, using the drilling
template provided.
• Fix using the 4 screws 12a (4,2 x
44,4) provided.
SNAP-ON FITTING
• The hood can be installed either di-
rectly on the bottom surface of the
wall units (min. 650 mm above the
hob) using snap-on side supports.
• Cut a fitted opening in the bottom
surface of the wall unit, as shown.
• Insert the hood until the side supports
snap into place.
• Lock in position by tightening the
screws Vf from underneath the hood.
CLOSING ELEMENT
• The space between the edge of the
hood and the rear wall can be closed
by applying the element 20 provided,
using the screws supplied for this pur-
pose.
15
264
502
Vf
30
12a
135
125125
20

Installation electrolux 7
EN
Connections
DUCTED VERSION AIR EXHAUST
SYSTEM
When installing the ducted version, con-
nect the hood to the chimney using ei-
ther a flexible or rigid pipe ø120 mm, the
choice of which is left to the installer.
• Insert the adapting ring 10 on the
hood body air outlet
• Fix the pipe in position using sufficient
pipe clamps (not supplied).
• Remove any activated charcoal fil-
ters.
RECIRCULATION VERSION AIR
OUTLET
• Cut a hole ø 125 mm in any shelf that may
be positioned over the hood.
• Connect the flange to the outlet on the
shelf over the hood using a flexible or rigid
pipe ø120 mm.
• Fix the pipe in position using sufficient
pipe clamps (not supplied).
• Fix the directional grille 8 on the recircula-
tion air outlet using the 2 screws 12e (2,9
x 9,5) provided.
• Ensure that the activated charcoal filters
have been inserted.
ELECTRICAL CONNECTION
• Connect the hood to the mains through a
two-pole switch having a contact gap of at
least 3 mm.
• When opening the sliding carriage for the
first time after installing the hood, pull it out
briskly until it clicks.
12e
8
9
125125
ø 125
10

8 electrolux Use
EN
USE
LLight Switches the lighting system
on and off.
M Motor Switches the extractor motor
on and off.
V Speed Sets the operating speed of
the extractor:
1.Low speed, used for a continuous
and silent air change in the presence
of light cooking vapour.
2.Medium speed, suitable for most
operating conditions given the op-
timum treated air flow/noise level
ratio.
3.Maximum speed, used for elimi-
nating the highest cooking vapour
emission, including long periods.
L
M - V
0
1
0
1
2
3

Maintenance electrolux 9
EN
Grease filters
CLEANING METAL CASSETTE GREASE
FILTERS
• The filters must be cleaned every 2
months, or more frequently in case of
particularly heavy use of the hood. Fil-
ters can be washed in a dishwasher.
• Pull out the sliding suction panel.
• Remove the filters one by one, after
having disconnected the relative fas-
tening elements.
• Wash the filters, taking care not to bend
them. Let them get dry before refitting
them. (The colour of the filter surface
may change throughout the time but
this has no influence to the filter effi-
ciency).
• When refitting the filters, make sure that
the handle is visible on the outside.
• Close the sliding suction panel.
Charcoal filter (Recycling version)
REPLACING CHARCOAL FILTERS
• These filters are not washable and
cannot be regenerated, and must be
replaced approximately every four
months or more frequently by particu-
larly heavy use.
• Pull out the sliding suction panel.
• Remove the grease filters.
• Remove the saturated carbon filter by
releasing the fixing hooks
• Replace the grease filters.
• Close the sliding suction panel.
Lighting
LIGHT REPLACEMENT
40 W incandescent light.
• Remove the metal grease filters.
• Unscrew the bulbs and replace them
with new ones having the same char-
acteristics.
• Replace the metal grease filters.
MAINTENANCE