eLEDing EE828WX User manual

1 – Solar Light Body（built in Rechargeable Li-Poly Battery) 1 – Tempered Glass Solar Panel 1 – Wall
Mounting Plate w/hardware 1 – Hardware Package with Screws and Anchors
Model EE828WX User Manual
Initial Installation Set-up (Refer to Fig. 1)
Included in this package:
IMPORTANT …. Read this User Manual Before Installing...!!!
®
SMART Solar Light … Built with Dual Ultra-Bright LED Head
Rev. EE828WDC 07062018 Page 1
9
eLEDing Solar Lights are SMART lights embedded with intelligent microprocessor
control chip. The light has two selectable operating modes, SMART A MODE (as
factory default) and SMART B MODE (Fig. 1-6). Both are SMART modes of
operation and utilize stored energy capacity for the most optimum lighting
efficiency.
The settings for Sensitivity/Range of motion, length of illuminating time with AUTO
Mode or levels of brightness in dimming control with ON/SMART Mode are set and
controlled with adjustable dials (Fig. 2)
The family of eLEDing SMART solar lights use an exclusive Intelligent Power
Management (IPM) embedded feature for managing and optimizing the Lithium
based battery for a full range of operation. This optimizes the battery’s life cycle to
adapt to most environmental conditions allowing both the battery and light to
perform for many years.
5
3.
7.
1.
Just “One Step” to Begin Using the Light
After the light fixture and solar panel are mounted and connected,
you may immediately begin using the light by just moving the
main switch to the ON (SMART) position. Using the factory pre-
set default profile is recommended (Fig.1-3). Note: NO
FURTHER ADJUSTMENTS ARE NECESSARY
Or
Full Coverage as Default Setting
Set as single head
Set as dual heads
Fig. 1 – Main Switch & Setup Reference
Fig. 2 – Functions Setting by Turning the Cover
1234
678
Built in replaceable battery is pre-charged and connected with the system before shipping
The light is ready for use. For initial check of the light unit and battery, please turn the switch to ON (Smart) position, the light will turn on within 5
seconds, then turn the switch back to OFF position for installation (refer Fig. 1). For most cases no pre-charge before use is needed.
Mounting the Light Body by use the mounting back plate (refer Fig 1-1 to 4)
1. The light body must only be mounted in a vertical position and it should be mounted at least 6 to 10 feet high above the ground
2. Choose a flat, secured and safe mounting surface. Mark the screw positions through the mounting plate screw holes onto the mounting surface.
Use 2 or 4 hole to mount (Fig. 1-2)
3. For wood/vinyl/metal surfaces, mount the back plate directly with provided or your standard screws. Drill clearance holes using a 3/16"
masonry bit for surface of concrete, brick or stucco. Insert the anchors (provided) with screws, then position the mounting plate and fasten the
screws securely
4. Attach the light body in position to complete the installation:
Band and remove the little tap at the back plate, turn the main switch to ON (SMART), insert the solar cable and plug it into the back
compartment, then put the whole light body onto the wall mount back plate (from top to buttom, with the light body “hinged” to the mounting plate).
Secure the unit with the small securing screw on the bottom of the light body (Fig. 1-1 to 4)
5. With the light body firmly secured, the Pan & Tilt feature allows users to adjust the direction of the LED light heads. By horizontally positioning
two light heads with a degree of 180o , the light can served as single head light and provide high-power illumination with wide up & down
coverage. A separate facing direction will give users a dual direction illumination with flexibility (Fig. 1-7 to 8). The facing direction of the motion
detector is fixed to horizontal, but the angle and the coverage can be selected up to 120o for wide angle coverage, and can also be set for one
direction only by turning the motion head’s plastic cover to either side (Fig. 2).
User Tips of Setting up the Solar Panel
The solar panel must be mounted in a non-obstructed position where can receive at least 4 hours direct sunlight on average all year round. It
should be mounted with a angle of 35°- 80° above the ground and face to the sky (Fig 1-5). A sturdy mounting location includes wall, roof, on
top of patio, under the leaves, secure pole, or floor/ground base. Make sure the solar panel is installed firmly for all weather conditions.
For Northern hemisphere installations, the solar panel should be mounted with South-facing position; For Southern hemisphere installation,
the solar panel should face to the North (Australia, South Africa, South America e. g.)
Attach the hardware mounting bracket to the solar panel. The cord is 10'-long and extension cable (model # EE-SPEC-15F) is available as
additional accessory. Estimate how long the cord is needed to reach the light body, and tie the unused part of the cord behind the solar panel
with the provided plastic zip-tie
Then mark the screw holes through the mounting bracket and secure the solar panel in position with the provided hardware
Firmly insert the solar panel cord into the light’s back compartment, make sure the cord connector is completely plugged into the light body as
the picture shows (Fig. 1-3).
Jumper2 (J2)
Open the cover to adjust setting
White
Black

“SMART B and AUTO” MODEs of Operation (Recommended Setting under Insufficient Sunshine, Refer Fig. 1-6)
“eLEDing” SMART Light MODES (may remove back cover to access a Jumper (J2) as required)
“SMART A” MODE of Operation (Recommended Factory Default Setting)
In SMART A mode with the jumper 2 (J2) Open/Off (Fig. 1-6), the light operates as a true Dusk to Dawn light. The unit senses its
surrounding ambient light level getting low and will turn ON in darkness, providing adjustable moonlight soft glow lighting all night
long. For the first 3 illuminating hours each night, this unit provides fixed dynamic lighting profile (70% to 30% of max brightness)
as eye compensation illumination regardless motion sensor to ensure having reasonable lighting level during the busiest hours in
the evening. The unit will slowly steps down its brightness as the ambient light level decreases during dusk time, provides a
smooth lighting for surrounding area. (Motion sensor is disable during the first 3-hours period of beginning the night) Once first 3
hours passed, the unit enters SMART dimming profile (as SMART B profile). In this profile, when motion been detected, the unit
will light up to maximum brightness within pre-set sensitivity range. With good sunlight coverage seasons and locations,
SMART A is highly recommended mode for most outdoor & indoor lighting solution.
Rev. EE828WDC 07062018 Page 2
In SMART B mode to be selected the jumper2 (J2) Closed/On, the light will directly enter the dimming profile without 3 hours’
fixed lighting profile (unlike SMART A). The light operates as a SMART sensing light and it lights up to full brightness when
motion is detected in darkness condition and pre-selectable dim to a lower brightness as a “Moon Light” profile once motion
stopped. The dimmed brightness can be adjusted by turning the Right Dial (Ref. Fig. 2, page 1) from 5% to 50% of max
brightness (do not turn to Min (0%) unless you wish to use Auto mode). The motion Sensitivity/Range can be adjusted by
turning the Left Dial. The length of delay time will automatically extended if motion continually to be detected, and the light will
not dim until the motion stopped and the Delay Time has expired. This adjustment has a motion sensing range from Low 10’,
Med. 20’, High 45’. SMART B is recommended for high latitude as insufficient sunshine locations at winter season.
When set Right Dial to minimum as 0% of max brightness in dim, the unit will convert a traditional AUTO Mode, as it will turn off
instead of dim down once Delay Time expired. Cautions: 1) avoid to set Sensitivity/Range too high in order to save battery
energy from false activations. 2) In AUTO Mode, If the IPM feature detects the battery has not enough stored energy caused by
very critical weather condition, it will automatically reduce the lighting level to half brightness in order to maintain a level of safe
lighting until it again receives enough sunlight to restore it back to normal status.
Set-up/Walk Test Procedure and Adjustments
1. To set up it for your applications, the unit comes with a Set-up/Walk Test mode as a AUTO mode only during this testing period to ensure
proper installation and optimize performance. To activate this mode, move the main switch from OFF to ON position. This Set-up/ Walk Test
mode can be reactivated at anytime to adjust your settings for your application by turn the switch to OFF then ON in any condition
day or night.
2. When the main switch is set initially to ON position for a period of 5 minutes, the Set-up/Walk Test mode/AUTO mode will be active, allowing
the user to adjust the light settings. This mode will work in both day and night time conditions. Sensitivity/Range can be adjusted at this time for
your application from 10' minimum to 45' maximum, also in conjunction adjust the dual light heads using the Pan and Tilt feature for your
application during this time.
3. The Set-up/Walk Test mode/AUTO mode is active once the unit is turn on, last for fixed 5 minutes. Under this mode, the Red LED indicator
will flash through the motion detection lens, providing visual confirmation of motion detection responds. Once 5 minutes passed, the unit will
automatically convert to normal operation mode (SMART A or pre-selected) and will illuminate once it senses a change to darkness from
daylight ambient light conditions. If installed during nighttime (no solar power), the unit will be set to Smart B mode, regardless its
current setting, and will restore to its current profile setting next evening (after one day-night cycle).
Note: The Red LED indicator light inside the ball head flashes for the following reasons: 1) To indicate motion activity during the 5 minutes
initial Set up/Walk Test. 2) To indicate the battery is low when the sensor detects motion during darkness. Storage: If this unit has been stored
over 12 months before initial operation then the battery may need to be re-charged. To re-charge the battery after storage turn the main switch
to OFF, plug the wire cord from the solar panel to the light and place it in direct sunlight for 1-2 days. Or make quickly charge for 2-3 hours by
using our exclusive optional accessory AC-DC Digital/Switched Power Adapter (EE-DPS-0.8A).
Product Specifications
EESGI guarantees this product to be free from defects in material & workmanship for (1) year.
This warranty does not apply to damage from misuse or incorrect installation/ connection. This warranty does not cover accessories, bulbs, batteries, accidents, alterations, unauthorized use or repair, neglect, misuse,
abuse, damages or defects resulting from normal wear and tear (including chips, fading scratches, abrasions or discoloration due to usage or sun exposure), or failure to follow instructions for care and maintenance, fire,
flood, and Acts of God. This warranty does not include liability for incidental or consequential damages. EESGI is not responsible for any damages in excess of the retail purchase price of the product under any
circumstances. The consumer is responsible for the installation of, removal of, and reinstallation of the product.
One Year Limited Warranty
Please unplug the battery when shipping the light or packing for fight traveling. Do not dispose of battery in fire as this may result in an explosion. Do not expose the light to fire or intense heat as the battery may
explode. Do not immerse in water. Never look directly into the light or shine it into another person’s eyes. Follow proper safety tips to prevent injury such as falling from a ladder during installation. Consult your local Bi-
Laws or local safety guide lines for installing the light fixture on a building.
Important Safety Information
Optional Accessories:
AC-DC Power Adapter (EE-DPS-0.8A) : Must be switch type (digital) 12VDC/0.5-1.5A with current limited power supply. Solar panel 15' extension cable (EE-SPEC-15F).
Customer Service: [phone], www.eesgi.com
Illuminating coverage: Up to 270º angle by dual heads Detecting Range: 120°, up to 45’x 45’ (L-10’, M-20’, H-45+’)
Light Head: 5W x 2 super bright -LED matrix (color 5000K) Energy Storage: 29WH Li-poly battery
Solar Panel: 13VDC/8W Tempered Glass (with 10' cable) SMART Mode: 8+hrs max bright set to 80+hrs min bright set
Weight: 1.7 LBs (Light Body) Operation Temp.: -4ºF to 125ºF, Weatherproof IP64
Brightness: =100W Halogen Lamp/1200+Lm (On Peak) Complies with: FCC Part 15 Class B and ICES-003:2004
Note: Installation with factory default settings is recommended for most applications
User tips
SMART Mode soft glow lighting can be adjusted by using the function Dimming dial, (Right Dial). This allows the user to select a dimming
level ranges from low to high, When motion is detected the light will brighten up to the default fixed max level and then gradually dim
down to the soft glow lighting level set by the user.
Caution -The higher the minimum soft glow level is set, the more stored battery energy will be consumed. If the IPM detects that the battery
does not have enough capacity to support the lighting profile, it will automatically switch to AUTO profile to provide safety lighting until it
receives enough sunlight to operate the feature correctly.
In Both SMART Mode, If your geographic location has outstanding daytime sunlight conditions all year (California, Nevada, Arizona, New
Mexico, Florida, Texas of USA e.g.) then you can increase the dimming level to take advantage of a brighter projection of Moonlight soft glow
Dusk-to-Dawn lighting. The Sensitivity/Range adjustment functions and setting are identically as described for the SMART B profile. For
most applications the recommending factory preset is SMART A Mode.
In both AUTO and SMART-ON profiles if the IPM detects that the battery does not have enough capacity to run either profile in critical
weather conditions, it will automatically disable illuminating function leaving only the charger active to protect the battery from over discharge
causing damage. Once enough sunlight is received to charge the battery, the unit will go back to AUTO profile if set in AUTO. if set to SMART-
ON profile then it will first go into AUTO profile until it receives enough sunlight energy to operate SMART-ON profile properly.
Avoid placing objects in front of the motion detector that may affect detecting performance. Avoid installing the unit near air conditioners, central heaters, or high
voltage systems. Avoid placing the motion detector head towards street traffic or other high movement areas which cause excessive triggers, resulting in shorter
battery reserve capacity. If this situation is unavoidable, decrease the sensitivity to achieve optimal balance. Motion detector is more sensitive to motions across the
device and less sensitive to motion moving towards or away from it. The solar panel should be mounted where maximum sunlight can be collected. Typically, the
solar panel should face south and avoid facing north (for Northern Hemisphere only, opposite way for Southern Hemisphere) with 35°- 80° tilt up direction (Refer to
Fig. 1-5) It’s fine facing to West or East where sunlight can directly charge the panel for at least 4 hours per day on average.
Use a soft wet cloth to periodically (at least once a year) clean the solar panel to avoid the reduction of energy output due to accumulated dust. Clean
accumulated snow as soon as possible during the snowing season.
Patented Technology