olympia electronics GR-8/leds User manual

GR-8/leds, GR-9/leds
OPERATION VOLTAGE
MAXIMUM POWER CONSUMPTION
BATTERY (Ni-Cd)
INDICATIONS - CONTROLS
CHARGE TIME
MINIMUM DURATION
LIGHT SOURCE
ILLUMINATION (MAINS/EMERGENCY )
DEGREES OF COVER PROTECTION
PRODUCED IN ACCORDANCE WITH
OPERATION TEMPERATURE RANGE
VIEWING DISTANCE (as safety sign)
RELATIVE HUMIDITY
CONSTRUCTION MATERIAL
EXTERNAL DIMENSION (L x W x H)
WEIGHT
GUARANTEE
GR-8/leds
GR-8/leds GR-9/leds GR-9/leds
3 W / 3.5 VA2.7 W / 3 VA
220-240V AC / 50-60Hz
3.6V/1Ah3.6V/0.6Ah
Charge LEDs, TEST Button
24 hours
1.5 hour
12 white LEDs
40lm / 100lm
IP42
EN 60598-1, EN 60598-2-22, ΕΝ 55015,
ΕΝ 61547, ΕΝ 61000-3-2, ΕΝ 61000-3-3
o
5 to 40 C
Up to 95%
ABS/PC, PC
15m
240 x 90 x 44 mm
345gr. 350gr.
3 years (1 year for the battery)
Olympia Electronics reserves the right to repair or to replace the returned goods
and to or not charge the buyer depending on the reason of defection. Olympia
Electronics reserves the right to charge or not the buyer the transportation cost.
Olympia Electronics guarantees the quality, condition and operation of the
goods. The period of warranty is specified in the official catalogue of Olympia
Electronics and also in the technical leaflet, which accompanies each product.
This warranty ceases to exist, if the buyer does not follow the technical
instructions included in official documents given by Olympia Electronics, or if the
buyer modifies the goods provided or has any repairs or re-setting done by a third
party, unless Olympia Electronics has fully agreed to them in writing. Products
that have been damaged can be returned to the premises of our company for
repair or replacement, as long as the warranty period is valid.
3 hours
38lm / 100lm
NON-MAINTAINED / MAINTAINED
EMERGENCY LUMINAIRES
Olympia Electronics - European manufacturer
Thank you for your trust in our products
Non Maintained operation: The luminaire lights its illumination source, only in
power supply’s failure.
(*) Maintained operation: The luminaire lights its illumination source, when it
is powered by the mains power supply or not.
90: 90 minutes duration
1: Maintained operation (*)
180: 180 minutes duration
G: Internally illuminated
NOTE: LED= Light Emitting Diode
LABELING EXPLANATION:
X: Self contained
A: Including test device
923378005_09_010 923378005_09_010
Warranty
Technical CharacteristicsLED Characteristics
Olympia Electronics S.A.MANUFACTURER
45 C max. across the board °
2.9-3.6V DC
780mW
2201159
Non reversible connection between main pcb and led module
MODEL NUMBER
VOLTAGE RANGE
CONNECTIONS
NOMINAL POWER
TEMPERATURE (tc)
4 5
European
manufacturers
72nd km. O.N.R. Thessaloniki-Katerini
P.C. 60300 P.O. Box 06 Εginio Pierias Greece
www.olympia-electronics.com
[e-mail]
IP42
Test button
TB
NM
M
15m Ni-Cd
Maintained
Non
maintained
Light output
100lm
X190A
G
Pictogram Installation
Various directions and symbols can be provided upon request.
The luminaire can be used as a safety sign. Place the apropriate pictogram to the
luminaire. In the package are icluded 3 pictograms:(807008002 Set of
Pictograms: Arrow Right, Arrow Left, Arrow Down).
Note!! The installer should fill in, on the specification label, the letter G if the
luminaire is used as a safety sign.
1. Dismantle the device (step 1 of the installation instructions).
2. Disconnect the connector and remove the old battery.
4. Follow step 7 of the installation procedure and power on the
device.
3. Connect the new battery with the same type (step 6 of the
installation instructions) and place it in the position of the old one.
It can be done only by a competent person and after the mains
interruption.
Battery Replacement

NOTE! The light source is non-user replaceable.
o
These luminaires are used indoors (ta 40 C) on the wall, where
emergency light is needed. Each luminaire must be permanently
connected to the mains power supply, according to Figure 5 (Page 3). In
normal operation the illumination LEDs are lit as well as the green
indicating charge LEDs, when the battery is charging. In case of a mains
power supply failure, the luminaire goes into emergency mode and the
led stripe is powered by the battery. When the mains power supply is
restored the device turns to normal operation.
ΑΤΤΕΝΤΙΟΝ!!!
1. Operations for installation, maintainance or testing must be done
by authorized personnel only.
2. The device must be connected to the mains power supply through
a fuse dependent by the total amount of the line’s power load.
Non-Maintained / Maintained operation there is an option to select
the non maintained or maintained operation by placing the jumper to
the appropriate place according to the Figure 4 (see page 2).
3. It is suggested to check every month the indication LED for battery
charging, and by pushing the TEST button to check the emergency
circuit. The led stripe should light as long as the TEST button is
being pressed. If the luminaire doesn’t work as described above,
contact the installer.
4. It is suggested to check every 6 months the minimum autononous
duration by disconnecting the mains power supply. Count the time
that the led strip lights and in case of less time than the nominal
autonomy, the battery must be replaced. If the measured time is
considerably less than the nominal autonomy contact the installer.
In case of battery or led stripe replacement, these must be
replaced by parts of the same type, by the manufacturer or by a
competent person.
6. I s not allowed to discard batteries into common trash bins, they t i
must be discarded only in battery recycling points. Do not
incinerate.
The light source contained in this luminaire shall only be
replaced by the manufacturer, his agent or a similar qualified
person.
5. In case of inactive use for a period greater than 2 months, the
battery must be disconnected fully charged, disconnect the battery
by pulling out the battery’s connector. This inactive condition
should not exceed 4-5 months.
Dismantle the device carefully by using a flat bladed
screwdriver.
Mount the plastic base on the wall (the test button must be
facing downwards) using the included mounting accessories in
points B and C.
Pass the mains cables through the hole (point A) and secure it
with a suitable bracket (not included) to ensure immobilization
of the cable at a distance of no more than 5cm from the
luminaire’s cable entry. ATTENTION!! To maintain the IP rating,
the outer diameter of the power cable must be at least 8.2 mm².
923378005_09_010 923378005_09_010 923378005_09_010
Refit carefully the removed plastic parts and power on the
device.
NOTE!!
After finishing the installation you must power the luminaire for at
least 24 hours in order to completely charge the battery. The rated
autonomy duration can be achieved after that time.
1
1
1
1
Luminaire
Mounting accessories
Set of Pictograms
Manual
Package Contents
General
Installation instructions
Non maintained
operation
Maintained
operation
Connect the mains cables to the terminal block.
Connect the battery`s cable with the appropriate terminal.
1 2 3
1
5
6
7
2
3
4
Accessory for Suspended Ceiling
The luminaire can be installed in a suspended ceiling, after the request of the
necessary accessories.
Α-3008 (927300800) Base for recessed mounting on suspended ceiling (Α-3018
Suspended ceiling mounting springs are included).
Mounting Springs
Α-3018