elektraLite LXE 700 Spot User manual

LXE 700 Spot USER MANUAL
(V1.26)
Elektralite (a division of Group One),
70, Sea Lane, Farmingdale, NY11735, U.S.A.
T. [phone]. F. [phone]
WWW.MYELEKTRALITE.COM

- １- LXE700 SPOT
For your own safety, please read this user manual carefully before installing LXE 700 Spot.
Every person involved with the installation, operation and maintenance of LXE 700 Spot has to:
-be qualified
-follow carefully the instructions of this manual
Introduction:
Thank you for choosing LXE 700 Spot.
When you unpack LXE 700 Spot, there should be in the box the fixture, a DMX 5 pin XLR cable, and a safety
cable. Please check carefully that there is no damage caused in shipping. If you notice any damage then
immediately let your shipper know and the dealer from whom you purchased LXE 700 Spot.
Features:
operation mode is by DMX 512 utilizing (24 channels) or stand alone or sound activation.
pan and tilt movement :
8 bit and 16 bit resolution for smooth and precise motion
pan : 630° rotation / tilt : 265° rotation
speed of pan/tilt movement is adjustable
electronic focus
strobe/shutter : high speed dual-blade shutter, 0-15Hz or random strobe
dimmer : mechanical adjustable from 0% to 100%
color : Full CMY Color mixing system.
Also a color wheel 1 has 8 dichroic filters plus white, with rainbow effect
gobos : 2 rotating gobo wheels, each wheel with 6 removable rotating gobos plus open, both wheels with
gobo shake and gobo indexing capability.
Multi-step zoom with 3 zoom angles.
Iris with an iris effect generator.
Frost with a frost effects generator
prism: 3- facet speed adjustable prism rotates in two directions with 16 prism macro effect
auto-program: 8 preprograms can be selected
display: can be inverted (180)° when LXE 700 spot is hung upside down.
local or remote resetting
lamp switches ON/OFF locally or remote, motor reset
auto test for all functions
value of each DMX-channel can be displayed
editable program:
edit and save a program to the “on board flash memory” using either the controls on the front panel or using
an external controller like an Elektralite CP-20. A maximum 48 scenes/cues/looks can be saved on board.
The resultant saved program can be played back from the “run” menu accessed from the front display panel

- ２- LXE700 SPOT
Safety Instructions.
This device has left the factory in perfect condition. In order to maintain this condition and to ensure a safe
operation, it is absolutely necessary for the user to follow the safety instructions and warning notes written in
this user manual. LXE 700 Spot is a high voltage fixture. Be careful when dealing with high voltages.
Please read this manual. If you do not read this manual and damages occur to LXE 700 Spot, then it
could void the warranty.
During shipping, LXE 700 Spot may have been exposed to high temperature changes or humidity changes. So,
as a precaution, do not switch LXE 700 Spot on immediately. Condensation can damage LXE 700 Spot so
leave LXE 700 Spot switched off until it has reached room temperature.
The electric connection must be carry out by a qualified person and it is absolutely essential that LXE 700 Spot
be grounded.
Always disconnect LXE 700 Spot from the power source, when the device is not in use or before cleaning it.
Only unplug LXE 700 Spot from the power cord. Never pull out the plug out by pulling on the power cord.
Take care, LXE 700 Spot will heat up when it is turned on and it will be very hot to touch.
Please keep LXE 700 Spot away from children and the general public. Please be intelligent and use common
sense when operating LXE 700 Spot.
General Guidelines.
LXE 700 Spot is a lighting fixture for professional use on stages, in theatres, arenas, churches and so on.
LXE700 Spot should only be operated at 120 volts and only indoors.
LXE 700 Spot should not be operated 24/7 (24 hours a day; 7 days a week). LXE 700 Spot needs operation
breaks to ensure that it will work for a long time without problems. Please do not shake LXE 700 Spot and
avoid using brute force when installing or operating it.
When choosing the location to install LXE 700 Spot, please make sure that it is not exposed to extreme heat,
moisture or dust. The minimum distance between LXE 700 Spot and the illuminated surface must be more
than 10 feet.
Always mount LXE 700 Spot with an appropriate safety cable. If you use the quick lock cam to hang LXE 700
Spot, please make sure the 4 quick lock fasteners are locked into position correctly.
Operate LXE 700 Spot only when you are familiar with the features on the fixture. Do not permit operation by
persons not qualified for operating it.
All modifications to LXE 700 Spot will invalidate the warranty. There are absolutely no exceptions.
If LXE 700 Spot is operated in any way different to the one described in this manual, LXE 700 Spot maybe
damaged and the guarantee will be void.

- ３- LXE700 SPOT
Installation Instructions.
a) Installing or replacing the lamp
Only install the lamp when LXE 700 Spot is unplugged from 120 volts.
The lamps must be replaced when it has reached the end of its lamp life or if it is damaged or deformed.
Before replacing the lamp let the lamp cool down. During operation, the lamp can
reach very high temperatures.
During the installation of the lamp do not touch the glass bulbs with bare hands. Always use a cloth to handle
the lamps during insertion and removal.
Do not install lamps with a higher wattage. They generate temperatures higher than LXE 700 Spot operating
temperature.
For the installation of the new lamp :
1234
Please remember the lamp is not hot-restrike. You must wait approximately 10
minutes before you can restrike the lamp.
Do not ever operate LXE 700 Spot with the cover open. The lamp is a discharge lamp. All discharge lamps,
irregardless of the manufacturer or type, are very volatile and can explode. Great caution must be exercised
when working with these lamps otherwise serious injury can happen.
b) Mounting LXE 700 Spot
The installation of LXE 700 Spot has to be built and constructed in a way that it can hold 10 times the weight
for 1 hour without any deformation.
The installation must always be secured with a secondary safety device (a safety cable).
Never stand directly below LXE 700 Spot when mounting, removing or servicing LXE 700 Spot.
The installer should make sure that LXE 700 Spot is installed correctly and that the installation is checked by
an expert on a regular basis.
If you are a rental house utilizing LXE 700 Spot, then use the appropriate half couplers (½ cheeseboros) to
secure the fixture to the truss or pipe. Remember to tighten down the cheeseboros before raising the truss.
Don’t laugh! It has been done before now. Remember with yoke fixtures on a flown truss, when you move them
the truss can move too. It’s just obeying Newton’s third law of motion: “to every action there is an equal and
opposite reaction”. Please remember this when securing the LXE 700 Spot fixture.
Cautions:
LXE 700 Spot should be installed outside areas where people can reach it, walk by it or be seated underneath
it when being installed. Overhead mounting requires experience including, amongst other things, calculating
the working load limits and installation material being used. Periodic safety inspections should be done of
LXE700 Spot as the fixture does move. If you do not have the qualifications and experience, do not attempt
the installation. Improper installation can result in bodily injury to yourself or others.
Before mounting make sure that the installation area can hold a minimum point load of 10 times LXE 700
Spot’s weight.
Once installed then connect LXE 700Spot to the correct power source. 120 volts A.C.

- ４- LXE700 SPOT
Installation via the Omega U Brackets.
1
2
3
4
(1)Omega-holders
(2)Clamp
(3)Safety-rope
(4)Quick-lock fastener
Screw one clamp (the clamp is not provided with LXE 700 Spot) onto each of the two Omega U brackets
supplied with LXE 700 Spot.
Insert the quick-lock fasteners of the first Omega bracket into the respective holes on the bottom of LXE 700
Spot. Tighten the quick-lock fasteners fully clockwise. Install the second Omega U bracket. Please do not use
pliers, crest wrenches and the like to turn the quick-lock fastener. If you do, there is very real likelihood that you
will break the Omega bracket. (These can be replaced at a substantial cost to your boss!)
Pull the safety cable through the holes on the bottom of the base and over the trussing or any secondary fixing
point. Do not clamp the cable to the U bracket or clamp. That is not a secondary safety point.
A secondary safety point is any point that will adequately hold LXE 700 Spot if the U brackets, clamps or the
fixtures base breaks or fails. Then the safety cable would be the backup and stop the fixture from falling to the
ground.

- ５- LXE700 SPOT
c) Locks for Pan and Tilt.
The LXE 700 Spot has two levers for locking the pan and the tilt function. These locks are engaged for
shipping.
The locks must be disengaged before turning on the fixture. The Pan lock is located in the middle of the yoke at
the base. While the tilt lock is located on one of the arms. The photo below shows the lock and unlock positions.
If the fixture is unlocked (and of course the fixture is not powered up) then the pan and tilt will move freely if you
push the head. If there is any resistance, recheck that you have unlocked the fixture completely.

- ６- LXE700 SPOT
DMX-512 Control Connection
Connect the provided XLR cable to the female 5-pin XLR output of your Elektralite CP 20 or other DMX
controller. The other end should be connected to the male 5-pin XLR input of LXE 700 Spot. Then daisy-chain
out of the first LXE 700 Spot and into the next LXE 700 Spot or other dmx device. Never “Y” split the DMX
connection.
If you need more cable, then it should be two core, screened cable fitted with a 5 pin XLR input and output
connector. Please refer to the diagram below.
1
2
3
4
5
DMX-512 connection with DMX terminator
For installations where the DMX cable has to run a long distance or is in an electrically “noisy” environment, it
is recommended that a DMX terminator is used. This helps prevent corruption of the digital control signal. The
DMX terminator is simply a 5 pin XLR plug (male) with a 120 Ωresistor connected between pins 2 and 3. It is
then plugged into the output XLR socket of the last LXE 700 Spot or other dmx device in the chain. Please see
illustration below.
1
2
3
4
5
Ω
120
DMX line

- ７- LXE700 SPOT
Projector DMX start address selection
All LXE 700 spots need be given a DMX starting address when using a DMX signal, so that the correct LXE
700 spot responds to the correct control signals. This digital starting address is the channel number from
which LXE 700 Spot starts to “listen” to the digital control information sent out from the Elektralite CP20 or
other DMX controller. The allocation of this starting address is done by setting the correct number on the
display located on the base of LXE700 Spot.
You can set the same starting address for all fixtures or group of fixtures, like all the LXE700 spots in your plot,
or you can make different address for each individual fixture.
If you set the same address, all the fixtures will start to “listen” to the same control signal from the same
channel number. In other words, changing the settings of one channel will affect all the fixtures simultaneously.
If you set a different address, each unit will start to “listen” to the channel number you have set, based on the
quantity of control channels of the fixture. That means changing the settings of one channel will affect only the
selected fixture.
In the case of this LXE 700 spot, which is a 24 channel fixture, you should set the starting address of the first
unit to 1, the second LXE 700 Spot to 25 (24 + 1), the third to 49 (25 + 24), and so on.
Note:
After switching on, LXE 700 spot will automatically detect whether DMX 512 data is received or not. If the data is received, the display will
show "A.001" or whatever the address is set to, like “A.025” If there is no data received at the DMX-input, the display flashes "A001" with
the actually set address. This situation can occur if:
- the 5 PIN XLR plug (cable with DMX signal from the controller) is not connected to the input of LXE 700 Spot.
or
-the controller is switched off or defective.
or
-the cable or connector is defective

- ８- LXE700 SPOT
The Display Panel:
Default settings shaded.
VA L U A001~AXXX (AXXX) DMX address setting
SLAV SLA1/ SLA2/ SLA3 Slave setting
ADDR
EBOC ON/OFF Change DMX address via
external controller
ALON (AU-A) Automatic Run in Stand Alone
AUTO MAST (AU-M) Automatic Run as Master
ALON (SO-A) Sound-controlled Run in Stand
Alone
RUN
SOUN
MAST (SO-M) Sound-controlled Run as Master
VA L U D–XX D-00 (DXXX) Display the DMX 512 value of
each channel
RDIS ON/OFF Reverse display
0 MODE
DISP
CLDI ON/OFF Shut off LED display
OPEN ON/OFF Lamp on/off
LAAU ON/OFF Lamp automated on with power
ONLI ON/OFF Lamp on/off via controller
1 LAMP
DELA D–XX D-05 Delay lamp on
RPAN ON/OFF Pan Reverse
RTIL ON/OFF Tilt Reverse
16BI ON/OFF Switch 16 bit/8 bit
DEGR 630/540 Pan degree select
MIC M-XX Mic sensitivity
AUTO Clos/Hold/Auto/Audi No DMX Status
FANS HIGH/AUTO Fan’s mode select
SPEE SP-1/SP-2 Movement Mode Select
REST Reset
LODA ON/OFF Restore factory settings
2 SET
VER V-1.0~V-9.9 Software version
LADJ ON/OFF Lamp adjustment
TEST T–01~T–30 Test function of each channel
CODE CXXX Fixture code *code is “C050”
3 ADJU
WHEL CH01~CH30 XXXX(-128~127) Motor Fix
LIFE 0000~9999(hours) Fixture running time
LAMP 0000~9999(hours) Lamp running time
CODE CXXX (Password is 038) Clear Timer Password
CLFE ON/OFF Clear fixture time
4 TIME
CLMP ON/OFF Clear lamp time
STEP S–01 ~S–48 Steps of Program Run
REC. RE.XX Auto Save Scene
C–01~C–30 0 1 XX(00~FFH)
3 0 XX(00~FFH) Edit the channels of each scene
TIME XXXX(000.2s~199.8s) Time for each scene
5 EDIT
SC01
~ SC48
CNIN ON/OFF Edit program via controller

- ９- LXE700 SPOT

- １０ - LXE700 SPOT

- １１ - LXE700 SPOT
Channel Functions:
CHANNEL 1 : color wheel 8 colors plus white, color cycle or rainbow effect
CHANNEL 2 : cyan color mixing
CHANNEL 3 : magenta color mixing
CHANNEL 4 : yellow color mixing
CHANNEL 5 : pan movement (max. 630°)
CHANNEL 6 : tilt movement (max. 265°)
CHANNEL 7 : speed of pan/tilt movement, or different blackout selection by wheels
CHANNEL 8 : rotating gobo wheel 1: 6 rotating gobos plus open , gobo cycle, gobo shaking
CHANNEL 9 : gobo rotation speed for gobo wheel 1. Adjustment in both directions
CHANNEL 10 : Indexing of the gobos on gobo wheel 1.
CHANNEL 11 : rotating gobo wheel 2: 6 rotating gobos plus open , gobo cycle, gobo shaking
CHANNEL 12 : gobo rotation speed for gobo wheel 2. Adjustment in both directions.
CHANNEL 13 : Indexing of the gobos on gobo wheel 2.
CHANNEL 14 : prism. Rotation of the prism. Plus 16 prism macro selectable
CHANNEL 15 : Electronic focus
CHANNEL 16: Zoom (three zoom lens available)
CHANNEL 17 : strobe effect maximum 15 flashes per second or random strobe, dimming and shutter
close/open control
CHANNEL 18 : Dimming effect 0-100% (only be activated while CHANNEL 17 is between
position 32 –63 DMX or between position 96-127 or between position 160-191 or
between position 224-255 values)
CHANNEL 19 : Iris movement with in built effects engine for iris.
CHANNEL 20: Linear Frost with built in effects engine for frost.
CHANNEL 21: Macros for the CMY color mixing and color wheel.
CHANNEL 22 : auto program control + lamp on, motor reset, lamp switch off
CHANNEL 23 : 16 bit pan movement (fine movement).
CHANNEL 24 : 16 bit tilt movement (fine movement).

- １２ - LXE700 SPOT
DMX Channel Function & Values:
Channel 1 - Color Wheel :
0-13 Open / white
14-27 Color 1
28-41 Color 2
42-55 Color 3
56-69 Color 4
70-83 Color 5
84-97 Color 6
98-111 Color 7
112-127 Color 8
128-189 Forwards rainbow effect fast to slow
190-193 No rotation
194-255 Backwards rainbow effect slow to fast
Channel 2 - Cyan Color Wheel :
0-255 Cyan (0-white, 255-100% Cyan)
Channel 3 - Magenta Color Wheel :
0-255 Magenta (0-white, 255-100% magenta)
Channel 4 - Yellow Color Wheel :
0-255 Yellow (0-white, 255-100% Yellow)
Channel 5 - PAN movement 8bit :
Channel 6 - TILT movement 8bit :
Channel 7 - Speed pan/tilt movement:
0-225 max to min speed
226-235 blackout by movement
236-245 blackout by all wheel changing
246-255 no function

- １３ - LXE700 SPOT
Channel 8 - Gobo Wheel 1 Select
0-9 Open
10-19 Rot. gobo 1
20-29 Rot. gobo 2
30-39 Rot. gobo 3
40-49 Rot. gobo 4
50-59 Rot. gobo 5
60-69 Rot. gobo 6
70-89 Gobo 1 shake slow to fast
90-109 Gobo 2 shake slow to fast
110-129 Gobo 3 shake slow to fast
130-149 Gobo 4 shake slow to fast
150-169 Gobo 5 shake slow to fast
170-189 Gobo 6 shake slow to fast
190-255 continuous rotation slow to fast
Channel 9 - Gobo wheel 1 Rotation
0-3 Gobo indexing (See Ch 10)
4-127 Forwards gobo rotation fast to slow
128-131 No rotation
132-255 Backwards gobo rotation slow to fast
Channel 10 - Gobo wheel 1 index
0-255 Gobo indexing
Channel 11 - Gobo wheel 2 select
0-9 Open
10-19 Rot. gobo 1
20-29 Rot. gobo 2
30-39 Rot. gobo 3
40-49 Rot. gobo 4
50-59 Rot. gobo 5
60-69 Rot. gobo 6
70-89 Gobo 1 shake slow to fast
90-109 Gobo 2 shake slow to fast
110-129 Gobo 3 shake slow to fast
130-149 Gobo 4 shake slow to fast
150-169 Gobo 5 shake slow to fast
170-189 Gobo 6 shake slow to fast
190-255 continuous rotation slow to fast

- １４ - LXE700 SPOT
Channel 12 - Gobo wheel 2 Rotation
0-3 Gobo indexing(see Ch 13)
4-127 Forwards gobo rotation fast to slow
128-131 No rotation
132-255 Backwards gobo rotation slow to fast
Channel 13 - Gobo wheel 2 index
0-255 Gobo indexing
Channel 14- 3 facet rotating prism
0-3 open
4-63 Forwards rotation from fast to slow
64-67 No rotation
68-127 Backwards rotation from slow to fast
128-135 Macro 1
136-143 Macro 2
144-151 Macro 3
152-159 Macro 4
160-167 Macro 5
168-175 Macro 6
176-183 Macro 7
184-191 Macro 8
192-199 Macro 9
200-207 Macro 10
208-215 Macro 11
216-223 Macro 12
224-231 Macro 13
232-239 Macro 14
240-247 Macro 15
248-255 Macro 16
Channel 15 – Focus:
0-255 Continuous adjustment from far to near
Channel 16 – Zoom:
0-85 Zoom1
86-171 Zoom2
172-255 Zoom3

- １５ - LXE700 SPOT
Channel 17 - Shutter, strobe:
0-31 Shutter closed
32-63 No function (shutter open)
64-95 Strobe effect slow to fast
96-127 No function (shutter open)
128-159 Pulse-effect in sequences
160-191 No function (shutter open)
192-223 Random strobe effect slow to fast
224-255 No function (shutter open)
Channel 18- Dimmer (intensity):
0-255 Intensity 0 to 100%
Channel 19– Iris:
0-191 Max. diameter to Min.diameter
192-223 Pulse opening fast to slow
224-255 Pulse closing slow to fast
Channel 20 –Frost:
0-191 Frost 0~100%
192-223 Pulse opening fast to slow
224-254 Pulse closing slow to fast
255 Max. Frost
Channel 21 - Color macros
0-7 OFF
8-15 Macro1
16-23 Macro2
24-31 Macro3
32-39 Macro4
40-47 Macro5
48-55 Macro6
56-63 Macro7
64-71 Macro8
72-79 Macro9
80-87 Macro10
88-95 Macro11
96-103 Macro12
104-111 Macro13
112-119 Macro14
120-127 Macro15

- １６ - LXE700 SPOT
128-135 Macro16
136-143 Macro 17
144-151 Macro 18
152-159 Macro19
160-167 Macro20
168-175 Macro21
176-183 Macro22
184-191 Macro23
192-199 Macro24
200-207 Macro25
208-215 Macro26
216-223 Macro27
224-231 Macro28
232-239 Macro29
240-247 Macro30
248-255 Random CMY
Channel 22– Lamp on/off, reset, Int. Prog.
0-19 color & gobo change normal
20-29 color change to any position
30-39 color & gobo change to any position
40-59 Lamp on
60-79 Lamp switch off
80-99 Motor reset
100-119 Internal program 1
120-139 Internal program 2
140-159 Internal program 3
160-179 Internal program 4
180-199 Internal program 5
200-219 Internal program 6
220-239 Internal program 7
240-255 Internal program 8
Channel 23 – Pan fine 16bit
Channel 24 –Tilt fine 16bit

- １７ - LXE700 SPOT
ERROR MESSAGE
When you turn on LXE700 Spot, it will reset first. The display may show “XXer” while there are problems with
one or more channels. “XX” stands for channel 1,2,3 and so on.
For example, when the display shows “01Er”, it means there is some error in channel1 (the color wheel. If there
are errors on channel 1, channel 2, channel 5 at the same time, you may see the error message “01Er”,
“02Er”,”05Er” flash repeatedly for 5 times, and then LXE 700 Spot will generate a second reset signal, This
reset with literally reset all the stepper motors. Usually after the second reset the error messages disappear
and the address number is displayed. Do not concern yourself if after the second reset that the address appear,
it is perfectly alright that the first reset fails. It is not a sign of a problem.
If the error message remains after performing reset after the second time, then the functions with the error will
not work but all other channels will more and the LXE 700 Spot will display its address number. The exception
to this rule is if the fixture has 3 errors or more. If this is the case then the fixture will not function until the
problem is sorted.
As an example of what to look for with an error message, here is the fault repair paradigm for 01Er:
01Er:
(Color-wheel 1 error) This message will appear after the reset of LXE 700 Spot if the magnetic-indexing circuit
malfunctions. This can mean a sensor failed or the magnet is missing or the color wheel stepping-motor is
defective or the drive circuit on the main circuit card for the motor is defective or the one (or more) wires
coming from the motor or sensor down to the circuit card is broken.
If any of the above happens then the color wheel will not be located in the default position after the reset.
CLEANING AND MAINTENANCE
The following points have to be considered during the inspection:
1) All screws, clamps etc. used to install LXE 700 Spot have to be tight and must not be corroded. Check them
regularly because, remember, LXE 700 Spot moves and so it will have an effect on whatever you are using to
hang the fixture.
2) There must not be any deformations on LXE 700 Spot’s housing and internal parts. Also check the points
where LXE 700 Spot is installed including such things as ceiling mounting points, truss, half couplers, C
clamps, safety cables and so on.
1) Mechanical moving parts must not show any traces of wearing and must rotate evenly.
2) The power input cable must not show any damage or material fatigue.
We recommend a frequent cleaning of the device. Please use a moist, lint- free cloth. Never use alcohol or
solvents. Pay particular attention to all the fans and their vents. That is where dust and debris can accumulate.
Accumulation of dust here can have a devastating effect on LXE 700 Spot. You must remove it regularly.
Failure to do so will cause overheating inside LXE 700 Spot. Overheating causes premature failure of the lamp
and other critical components. Do not use a air hose to clean the fans and vents. All you will do is bow the dust
right into the fixture and all over the dicroic colors and gobos.
There are no serviceable parts inside LXE700 Spot except for the lamp. Please refer to the
instructions under “Installation instructions” to change lamp.
Should you need any spare parts, please order genuine parts from your local dealer.

- １８ - LXE700 SPOT
TECHNICAL SPECIFICATIONS
Power Supply :
□120VAC,60Hz;
Power consumption : max. 800VI.
Lamp : HSR 700 (or MSR700/2)
Motors : 24 micro motors
Packing dimensions :30” x 22” x 18” (76.5mm x 55.5mm x 46.5mm)
Net weight : 75 pounds (34Kgs)
Please note, Elektralite is constantly improving their product range and we reserve the right to make changes
without prior notice.
Other Elektralite Products include :
[Also check out our website at www.myelektralite.com]
CP-20xt Controller.
TurboFog + Fog Machine.

- １９ - LXE700 SPOT
Turbohazer Haze Machine.