ETC Desire XTI Series User manual

Part Number: 7410M1250-1.8.2 Rev: C
Released: 2022-10
Desire Series by ETC
D40/D60 XTI
User Manual
Version 1.8.2

To view a list of ETC trademarks and patents, go to etcconnect.com/ip . All other trademarks, both
marked and not marked, are the property of their respective owners.
ETC intends this document, whether printed or electronic, to be provided in its entirety.

Table of Contents i
Table of Contents
Introduction. . . . . . . . . . . . . . . . . . . . . . . . .1
Quick Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
Vivid, Lustr+, Fire, Ice and Studio HD . . . . . . . . . . . . . . . . . . . .1
Studio Daylight, Studio Tungsten . . . . . . . . . . . . . . . . . . . . . . .1
Models. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
Applications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
FCC Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
Document Conventions . . . . . . . . . . . . . . . . . . . . . . . . .4
Safety. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Environment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
Help from ETC Technical Services . . . . . . . . . . . . . . . . .6
Chapter 1 Quick Start . . . . . . . . . . . . . . . . . . . . . . . . . .7
Install . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Focus . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Configure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Set DMX Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Quick Setups . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
Quick Setups (Vivid, Lustr+, Fire, Ice, and Studio HD) . . . . . . .7
Quick Setups (Studio Daylight, Studio Tungsten). . . . . . . . . . .8
Chapter 2 Installation . . . . . . . . . . . . . . . . . . . . . . . . . . 9
Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Dimensions and Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Fixture Weight . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
Installation Clearances . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
Typical Power Consumption D40XTI . . . . . . . . . . . . . . . . . . . .12
Typical Power Consumption D60XTI . . . . . . . . . . . . . . . . . . . .13
Note About LED Fixtures . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
Color Rendering Index and Color Quality Scale Ratings . . . .14
Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Installation on a Pipe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Accessory Installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Installation on a Permanent Base . . . . . . . . . . . . . . . . . . . . . .17
Installation on a Pole . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

ii Desire D40/D60 XTI v1.8.2 User Manual
Installation on a Wall . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Power and Data Cabling Requirements . . . . . . . . . . . . . . . . .18
Indicator Lights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
DMX Addressing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19
Chapter 3 DMX Profiles . . . . . . . . . . . . . . . . . . . . . . .20
Vivid, Lustr+, Fire, Ice, and Studio HD Profiles . . . . . .20
Direct Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .20
HSI (Hue Saturation Intensity) and HSIC (Hue, Saturation,
Intensity, Color Temperature (White Point)) . . . . . . . . . . . . .21
RGB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Studio . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Strobe . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
Plus 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Color Matching . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
Studio Daylight, Studio Tungsten Profiles . . . . . . . . .24
Direct Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
Channel Mapping and DMX Input Profiles. . . . . . . . .24
Vivid, Lustr+, Fire, Ice, Studio HD. . . . . . . . . . . . . . . . . . . . . . .24
Studio Tungsten and Daylight . . . . . . . . . . . . . . . . . . . . . . . . .24
Vivid, Lustr+, Fire, Ice, Studio HD. . . . . . . . . . . . . . . . . . . . . . .25
Studio Tungsten and Daylight . . . . . . . . . . . . . . . . . . . . . . . . .26
Chapter 4 Operation. . . . . . . . . . . . . . . . . . . . . . . . . .27
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
Gadget II . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
DMX/RDM Gateway . . . . . . . . . . . . . . . . . . . . . . . . . . .29
Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
DMX Address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Data Loss . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
Plus 7 (Vivid, Lustr+, Fire, Ice, and Studio HD) . . . . . . . . . . . .30
LED Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
Status Indicators . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .33
Over Temp. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Restore Defaults . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Software Update Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .34
Presets and Sequences . . . . . . . . . . . . . . . . . . . . . . . . .35
Presets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .35
Sequences . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .36
Appendix A RDM Commands . . . . . . . . . . . . . . . . . . . . 37

Introduction 1
Introduction
Congratulations on your purchase of a Desire Series D40/D60 XTI fixture by ETC.
The Desire XTI Series is designed for permanent installations indoors or outdoors, with an IP66
rating, rugged die-cast enclosure, and noiseless fan-free operation. Up to 32 Desire XTI
fixtures can be linked together on one data chain and configured over a DMX/RDM network.
Desire’s x7 Color System seven-hue technology produces a light and color quality that
conventional LED systems cannot duplicate. This unique color system produces bright, broad-
spectrum whites and intense colors equally well, rendering pigments, objects, and skin tones
in a natural way.
Fire and Ice fixtures use elements of the x7 Color System for superior performance in deep
saturated colors.
Studio Daylight and Studio Tungsten fixtures use high-output white LEDs for maximum
brightness and efficacy. Studio Tungsten interacts very well with incandescent sources, while
Studio Daylight easily replaces a variety of HMI lamps and natural sunlight.
Quick Setups
You can use any one of the Quick Setups and fine-tune settings for operation via DMX/RDM
protocol.
Vivid, Lustr+, Fire, Ice and Studio HD
Some of the options include:
• Multiple DMX profiles ranging from a simple 3-channel RGB profile to 8-channel native color and
intensity control.
• Multiple dimming curve options.
• Preset colors and sequences for standalone operation.
• White point selection; white light and color behavior based on a specific color temperature white
light such as 3200 K or 5600 K.
• Loss-of-data behavior options.
• Power regulation modes; three output options that offer a choice between maximum light
output for lower duty cycles and maximum thermal stability and output consistency for higher
duty cycles.
Studio Daylight, Studio Tungsten
Some of the options include:
• Multiple dimming curve options.
• Presets and sequences for standalone operation.
•Strobe.
• Loss-of-data behavior options.
• Power regulation modes; three output options that offer a choice between maximum light
output for lower duty cycles and maximum thermal stability and output consistency for higher
duty cycles.

2Desire D40/D60 XTI v1.8.2 User Manual
Figure-1.1 Components of a D40/D60 XTI Fixture.
Figure-1.2 Components of the Rear Panel.
Models
Each member of the Desire Series product line is unique and optimized for a specific lighting
task. All fixtures feature narrow optics for the longest throws.
Vivid
• Full 7-color x7 LED array
• Optimized for high-output deep pastels and strong saturated colors—an all-around workhorse
for vibrant color washes
Lustr+
• Specialized x7 LED array with 6 colors plus white
• Broad-spectrum color optimized for the best white and light tints across the entire white and
pastel range
• Beautifully illuminates skin tones and other objects—ideal for theatrical lighting
Fire (discontinued)
• Optimized for saturated colors at the red end of the spectrum
• Strongest output for high-intensity washes and theatrical environments
Ice (discontinued)
• Optimized for saturated colors at the blue end of the spectrum
• Strongest output for high-intensity washes and theatrical environments
Studio HD
• Precise mix of warm white and cool white LEDs plus additional colors for more spectral power
• Continuously variable color temperature white light
• Extreme CRI and high-definition illumination of skin tones from 2700 K to 6500 K
LED array
Yoke
Trim ring
Yoke
locking bolt
Safety
cable loop
Power in
DMX/RDM in
and thru
Status indicators

Introduction 3
Studio Daylight
• 5,700 K nominal correlated color temperature
•70CRItypical
Studio Tungsten
• 3,000 K nominal correlated color temperature
•85CRItypical
Applications
Compliance
The Desire D40/D60XTI Series fixture complies with and has been tested to the following
regulatory standards:
• ETL Listed to UL 1598 USA / CSA C22.2 No. 250.0-08 Canada
• CE EN55015:2006 + A1:2007 / EN55022:2006 + A1:2007 Class B / EN61000-3-2:2006 +
A2:2009 / EN61000-3-3:2008 / EN61547:1996 + A1:2000
FCC Compliance
Desire D40/D60XTI Series
(For any FCC matters):
Electronic Theatre Controls, Inc.
3031 Pleasant View Road
Middleton, WI 53562
[phone]
etcconnect.com
This device complies with Part 15 of the FCCRules. Operation is subject to the following two
conditions:(1) this device may not cause harmful interference, and (2)this device must accept
any interference received; including interference that may cause undesired operation. Visit
etcconnect.com/products for current and complete compliance information including FCC
compliance.
•Houses of worship •Outdoor signage
•Museums •Outdoor performance venues
•Theme parks •Public sculptures
•Commercial buildings
Note:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. Any
modifications or changes to this product not expressly approved by Electronic
Theatre Controls, Inc. could void the user’s authority to operate the product.
Operation of this equipment in a residential area is likely to cause harmful
interference, in which case the user will be required to correct the interference at
their own expense.

4Desire D40/D60 XTI v1.8.2 User Manual
Document Conventions
Throughout this manual, the following are used to alert you to notes and safety notices.
Please email comments about this manual to [email protected].
Note:
Notes are helpful hints and information that is supplemental to the main text.
CAUTION:
A Caution statement indicates situations where there may be undefined or
unwanted consequences of an action, potential for data loss or an equipment
problem.
WARNING: A Warning statement indicates situations where damage may occur, people
may be harmed, or there are serious or dangerous consequences of an action.
WARNING: RISK OF ELECTRIC SHOCK! This warning statement indicates situations where
there is a risk of electric shock.

Introduction 5
Safety
The Desire series fixtures are intended for professional use only. Read entire User Manual
before using equipment.
Environment
• Maximum recommended ambient operating temperature: Ta=40°C (104°F)
• Maximum anticipated external surface temperature: Tmax=80°C (158°F)
• External temperature after 5 minutes of full-brightness operation and 23°C (74°F) ambient: 38°C
(100°F)
• External Temperature (steady state achieved) at 23°C (74°F): 70°C (158°F)
WARNING: • Do not mount the fixture on or near a flammable surface.
• In addition to primary suspension, attach a safety cable (or other
approved safety device) to the fixture.
• Disconnect the fixture from power and DMX and allow it to cool
before installing accessories or performing any cleaning and
maintenance.
• Only use mounting hardware that is rated for the total weight of the
fixture and accessories.
• Mount and support the fixture only by the primary suspension holes
in the yoke or mounting brackets.
• Do not mount the fixture in a marine environment (within five
kilometers [three miles] of a saltwater body of water).
AVERTISSEMENT : • Ne pas installer le projecteur sur ou à côté d’une surface inflammable.
• En plus de la suspension principale, fixez une chaîne de sécurité (ou
tout autre dispositif de sécurité homologué) au projecteur.
• Débranchez le projecteur de son alimentation et du DMX et laissez-le
refroidir avant d’installer des accessoires ou d’effectuer un nettoyage
ou un entretien.
• N’utilisez que de la quincaillerie de montage adaptée au poids total
des projecteurs et des accessoires.

6Desire D40/D60 XTI v1.8.2 User Manual
Help from ETC Technical Services
If you are having difficulties and your problem is not addressed by this document, try the ETC
support website at support.etcconnect.com or the main ETC website at etcconnect.com. If
none of these resources are sufficient, contact ETC Technical Services directly at one of the
offices identified below. Emergency service is available from all ETC offices outside of regular
business hours.
When calling for help, please have the following information handy:
• Product model and serial number (located on back panel)
• Dimmer manufacturer and installation type
• Other components in your system (Unison, other consoles, etc.)
ETC, Inc.
Americas
Technical Services Department
3031 Pleasant View Road
Middleton, WI 53562
800-775-4382 (USA, toll-free)
[phone]
[email protected]
ETC GmbH
Germany, Austria, Switzerland, Eastern
Europe, and Russia
Technical Services Department
Ohmstrasse 3
83607 Holzkirchen, Germany
[phone]
[e-mail]
ETC Austin
High End Systems Products
Technical Services Department
2105 Gracy Farms Lane
Austin, TX 78758 USA
800-890-8989 (USA, toll-free)
[phone]
[email protected]
ETC France
France
Zone Urbaparc -
Bâtiment E
6 Boulevard de la Libération
Saint-Denis, 93200
[phone]
[email protected]
ETC Ltd
Europe, Middle East, and Africa
Technical Services Department
26-28 Victoria Industrial Estate
Victoria Road,
London W3 6UU England
[phone]
[email protected]
ETC Asia
Asia
Technical Services Department
Room 1801, 18/F
Tower 1, Phase 1 Enterprise Square
9 Sheung Yuet Road
Kowloon Bay, Kowloon, Hong Kong
[phone]
[email protected]

Quick Start 7
Chapter 1
Quick Start
This section will help you to quickly use the Desire XTI Series fixture. For complete, detailed information
and step-by-step instructions, see
Installation on page 9 and Operation on page 27 .
Install
1. Hang or mount the fixture using the provided hardware and approved hardware accessories.
2. Attach an approved safety cable.
3. Install a secondary lens, if needed, with the smooth side out.
4. Attach additional accessories (half shield, louver, etc.), if needed, onto the fixture.
Focus
1. Using an RDM configuration tool or DMX/RDM control device, turn the fixture on to full
intensity.
2. Adjust the fixture’s position as needed.
3. When focusing is complete, return the fixture to normal operation.
Configure
Set DMX Address
Using an RDM configuration tool or RDM lighting control device, set the address of the fixture.
Quick Setups
Various pre-programmed combinations of operational settings are available to quickly get you started.
These settings are specifically created for different situations and are easily accessible with an RDM
configuration tool or RDM lighting control device.
Quick Setups (Vivid, Lustr+, Fire, Ice, and Studio HD)
Quick Setup Description Profile Features
General
General lighting:
• All-purpose settings for most lighting
applications.
• The default setup except for fixtures
with Studio LED arrays.
Direct
control
• Standard dimming curve
• Regulated output for brightness
consistency
• Individual color channels plus master
intensity control
• Allows for native color space
crossfades
Stage
Theatrical lighting:
• Tungsten-like performance and
precise color-control.
• Uses the most DMX channels of all
quick setups.
HSI
Plus 7
enabled
• Incandescent dimming curve
• Regulated output for brightness
consistency
• White point: 3200 K

8Desire D40/D60 XTI v1.8.2 User Manual
Quick Setups (Studio Daylight, Studio Tungsten)
XT Arch
Outdoor and extreme environments:
• Longevity and reliability in
applications with limited access.
• High degree of output consistency
and protection against temperature
swings.
HSI
• Standard dimming curve
• Protected output for high-heat
environments
• Reduced overall brightness
• White point: 3200 K
High Impact
Concerts and High Impact lighting:
• Enables quickest response, simple
RGB control and strobe channel for
maximum effect usage.
RGB
• Quick dimming response
• Boosted output for maximum
intensity
• Reduced consistency of output
• White point: 5600 K
Studio
Video or film lighting:
• Enables quick, comprehensive
control of white light via DMX or
RDM.
• High-quality white-light output.
• The Studio Quick Setup is
operational in all fixtures for
excellent white light performance. It
is the default setting for Studio
fixtures.
Studio
• Linear dimming curve
• Regulated output for brightness
consistency
• Variable white point of 2950 to 6500
K
• Variable green/magenta balance (tint)
Quick Setup Description Profile Features
Studio
Video or film:
• The default setting for Studio
Daylight and Studio Tungsten
fixtures.
Studio
• Linear dimming curve
• Regulated output for brightness
consistency
• Strobe enabled
Stage
Theatrical lighting:
• Behaves like a theatrical fixture in
control and dimming performance.
Direct
• Incandescent dimming curve
• Regulated output for brightness
consistency
• Strobe enabled
Single
Channel
Architectural installations:
• Most streamlined settings for
applications with limited control
options.
Direct
• Standard dimming curve
• Regulated output for brightness
consistency
Quick Setup Description Profile Features

Installation 9
Chapter 2
Installation
Specifications
Physical
• Rugged die-cast aluminum construction
• Advanced thermal management systems for long LED life
• Easy-to-remove trim ring for accessories
• Ambient operating temperature -20 to 40°C
(-4to104°F)
• Continuous operation at 40°C (104°F)
• Stainless steel mounting yoke
• Available in black (standard), white (optional), silver, or
custom colors (contact factory)
• Rated IP66 for exterior use
• No-noise, fan-free convection cooling for acoustically
sensitive installations
• See
Fixture Weight on page 10
Electrical
• 100 V to 240 V 50/60 Hz universal power input
• Requires power from non-dim source
• Up to 32 fixtures may be linked on one data chain
LEDs
• 40 or 60 Luxeon®Rebel™LED emitters
(Vivid, Lustr+, Fire, Ice, and Studio HD)
• 50,000 hr. LED life (50,000 hours to 70% intensity)
• 40 or 60 Luxeon Rebel ES LED emitters
(Studio Daylight and Studio Tungsten)
• See
Note About LED Fixtures on page 14
Optical
• Tight primary field angle of 17°
(Vivid, Lustr+, Fire, Ice, and Studio HD)
• Tight primary field angle of 24°
(Studio Daylight and Studio Tungsten)
• Secondary lenses available for multiple beam spread
options including round, oblong, and linear patterns
• Combine linear lenses for desired beam spread
Color
• Specialized capabilities from different LED array options
based on x7 color-mixing expertise:
– Vivid: Optimized for strong, saturated colors at
maximum brightness
– Lustr+: x7 Color System array with a high-intensity
white LED for an ideal theatrical wash light. Full range
color, with an emphasis on lighter colors and white.
– Fire and Ice (discontinued): Optimized for high-
intensity saturated colors in either the warm, red end
of the spectrum (Fire) or the cool, blue end of the
spectrum (Ice).
– Studio HD: Optimized for variable color temperature
white light.
• Interacts seamlessly with conventional sources
• Achieves excellent 3200° or any other Correlated Color
Temperature white light from 2000°K to 10,000°K
(except Fire or Ice) (CCT adjustment not available on
Studio Daylight and Studio Tungsten)
• Beautifully illuminates skin tones and other objects
• Deeply saturated colors across an exceptionally wide
gamut
Control
• DMX512-A compliant
• DMX in via 6 foot cord and supplied DMX termination
board
• RDM functionality for address and setting changes and
playing presets
• Console-free presets and sequences via RDM device
• Multiple profile options for different levels of control
• Optional strobe channel
• Master/slave mode
• 15-bit virtual dimming engine for smooth, high-quality
theatrical fades
• See
DMX Addressing on page 19

10 Desire D40/D60 XTI v1.8.2 User Manual
Dimensions and Clearances
Use the following dimensions to allow proper clearances around the fixture. Allow additional space for
cables.
Figure-2.1 D40/D60 XTI Dimensions.
Fixture Weight
Total weight depends on how the individual fixture is configured.
*Does not include mounting hardware.
Model Weight* Shipping Weight
lb kg lb kg
D40XTI 15 6.8 18 8.2
D60XTI 23 10.43 24.7 11.2
7.1"
180 mm
5.6"
141 mm
14.7"
373 mm
11.6"
294 mm
19.1"
486 mm
4.5"
114 mm
11.0"
278 mm
4.1"
105 mm
8.3"
211 mm
13.3"
338 mm
17.7"
450 mm
9.2"
234 mm
8.5"
216 mm
20.5"
521 mm
16.1"
408 mm
12.8"
325 mm
114 mm
4.5"
12.0"
305 mm
7.3"
186 mm
4.8"
9.7"
246 mm
123 mm
14.2"
18.6"
361 mm
474 mm
10.6"
9.9"
270 mm
251 mm
D40XTI
D60XTI

Installation 11
Installation Clearances
Cooling and Duty Cycle
The D40/D60 XTI fixture is convection cooled and can operate all channels at full power continuously
in ambient temperatures up to 40°C (104°F).
If ambient conditions exceed 40°C (104°F) or fail to allow sufficient airflow, over a long period of time,
the fixture may shut down and remain off until they return to a safe operating temperature. The fixture
provides two methods to indicate over temperature:
• Visible: The LED array glows in a dull, low intensity with only some emitters illuminated and the
Error Indicator light turns on.
• Dark: The LED array turns off.
LED life is adversely affected by high-temperature operation. When operating under elevated ambient
temperatures, avoid turning all channels to 100% for extended periods, such as channel checks or
focusing.
CAUTION:
Duty Cycle
Operating the fixture in higher ambient temperatures or low-airflow
situations may cause the power supply to shut down. Following a cool-down
period, the power supply will automatically reset and the fixture will return
to operation.
It is good practice to power down any device with on-board electronics to
limit unnecessary wear on the devices and eliminate residual use of electricity.
When not in use, Desire fixtures should be powered down by disconnecting
from power at the breaker.

12 Desire D40/D60 XTI v1.8.2 User Manual
Typical Power Consumption D40XTI
Vivid
Lustr+
Fire
Ice
Studio HD
Studio Daylight
Studio Tungsten
100V 120V 240V
Idle Power / Current 10.5W / 0.135A 11W / 0.098A 12.7W / 0.078A
100% Boost Power / Current 102W / 1.12A 98W / 0.82A 95.6W / 0.403
100V 120V 240V
Idle Power / Current 10.3W / 0.125A 10.5W / 0.094A 12.2W / 0.074A
100% Boost Power / Current 104W / 1.16A 102W / 0.861 99.7 W / 0.418
100V 120V 240V
Idle Power / Current 10.5W / 0.125A 10.8W / 0.096A 12.5W / 0.076A
100% Boost Power / Current 91.2W / 1.02A 88.2W / 0.74A 87.2W / 0.369A
100V 120V 240V
Idle Power / Current 11.0W / 0.123A 11.2W / 0.099A 12.8W / 0.077A
100% Boost Power / Current 104.2W / 1.17A 102.2W / 0.867A 99.5W / 0.42A
100V 120V 240V
Idle Power / Current 11.1W / 0.134A 11W / 0.097 A 12.8W / 0.077A
100% Boost Power / Current 106.2W / 1.19A 103.5W / 0.883A 101.3W / 0.426A
100V 120V 240V
Idle Power / Current 10.6W / 0.123A 10.6W / 0.095A 12.4W / 0.076A
100% Boost Power / Current 105.1W / 1.12A 103.3W / 0.878A 100.8W / 0.424A
100V 120V 240V
Idle Power / Current 10W / 0.111A 10.1W / 0.093A 11.9W / 0.075A
100% Boost Power / Current 104W / 1.05A 103.1W / 0.872A 100.3W / 0.422A

Installation 13
Typical Power Consumption D60XTI
Vivid
Lustr+
Fire
Ice
Studio HD
Studio Daylight
Studio Tungsten
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.3W / 0.075A 4.1W / 0.067A
100% Boost Power / Current 117.9W / 1.19A 118W / 1A 115.6W / 0.526
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.2W / 0.075A 4.3W / 0.069A
100% Boost Power / Current 123.7W / 1.24A 123.6W / 1.04 121W / 0.546
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.3W / 0.075A 4.2W / 0.067A
100% Boost Power / Current 108.8W /1.1A 108.4W / 0.92A 106.2W/ 0.491A
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.2W /0.075A 4.3W / 0.068A
100% Boost Power / Current 129.W / 1.26A 124.4W / 1.05A 121.8W / 0.55A
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.3W / 0.76 A 4.3W / 0.068A
100% Boost Power / Current 125.1W / 1.26A 124.7W / 1.05A 122.5W / 0.552A
100V 120V 240V
Idle Power / Current 4.2W / 0.08A 4.3W / 0.76 A 4.2W / 0.068A
100% Boost Power / Current 125.1W / 1.26A 124.7W / 1.05A 122.5W / 0.552A
100V 120V 240V
Idle Power / Current 4.3W / 0.08A 4.2W / 0.073A 4.2W / 0.065A
100% Boost Power / Current 124.4W / 1.25A 123.7W / 1.04A 121.2W / 0.545A

14 Desire D40/D60 XTI v1.8.2 User Manual
Note About LED Fixtures
All LED sources experience some lessening of light output and some color shift over time. Desire Series
fixtures have complex thermal management systems to minimize these changes. With typical usage, a
Desire fixture will still achieve at least 70% of its initial output after 50,000 hours of use (B50, L70). In
individual situations, LEDs will be used for different durations and different levels. This can eventually
lead to minor alterations in color performance, necessitating slight adjustment to presets, cues, or
programs.
All LEDs may exhibit a slight shift in output as they rise to full operating temperature. Desire Series
fixtures allow the selection of different power settings in order to balance the competing requirements
of thermal stability and brightness. Depending on the selected setting, changes in output as fixtures
warm up may or may not be visible to the eye.
Color Rendering Index and Color Quality Scale Ratings
Desire fixtures are evaluated for Color Rendering Index (CRI) and Color Quality Scale (CQS)
performance using measured output spectrum and optimized mix solutions for a best spectral match
to black body sources at 3200 K and 5600 K. Color fidelity was also measured. These numbers may
fluctuate slightly from fixture to fixture. This is a normal characteristic of white LEDs, and this kind of
variation is highly unlikely to be apparent in most applications. The performance is the same for all
fixture versions.
Desire luminaires provide excellent color rendering, particularly the color-mixing versions. A Duv rating
of 0.000 indicates that the color mix used was exactly on the black body line, with no green or
magenta tint.
Studio Daylight and Studio Tungsten fixtures use only white-type LEDs at a fixed color temperature in
order to maximize output and efficacy.
Fixture CRI CQS Color Fidelity Duv
Vivid at 3200 K 87 89 89 0.000
Vivid at 5600 K 90 92 92 0.000
Lustr+ at 3200 K 86 88 88 0.000
Lustr+ at 5600 K 93 92 90 0.000
Studio HD at 3200 K 89 90 91 0.000
Studio HD at 5600 K 92 94 94 0.000
Studio Tungsten at 3000 K 86 86 86 0.001
Studio Daylight at 5600 K 71 70 69 0.001

Installation 15
Installation
The D40/D60 XTI fixtures can be mounted four ways.
• On a pipe with a C-clamp
• On a permanent base
•Onapole
•Onawall
Install on pipe or a suitable, rigid, permanent base with secured bolts. This can include poured concrete
pads, factory-supplied pole-top and wall-mount brackets, and other attachments which meet the
published weight and wind-load requirements for the fixture.
*Does not include mounting hardware.
Detailed installation information is packaged with the fixture. See the D40/D60 XTI Installation Guide .
Installation on a Pipe
The D40/D60 XTI fixtures can be hung from a pipe using a C-clamp. The C-clamp attaches the fixture
to the mounting pipe and allows you to adjust the position of the fixture once it is mounted.
1. Tightly fasten the C-clamp to the yoke with the provided yoke bolt and lock washer.
2. Place the C-clamp on mounting pipe, then tighten the pipe bolt to secure it.
3. Loosen the C-clamp pan screw and rotate the yoke to the desired position.
4. Tighten the pan screw to lock the fixture.
Model Weight* Shipping Weight Wind Rating
lb kg lb kg
D40XTI 15 6.8 18 8.2 .72 EPA
D60XTI 23 10.43 24.7 11.2 .95 EPA
Note:
The EPA number is obtained by estimating Cd(Wind Drag Coefficient) and
multiplying it with the projected area of the object. Wind Drag Coefficients were
obtained from AASHTO Sixth Edition 2013.
WARNING: Do not use this fixture with a damaged power lead. If the power lead (cord
set) is damaged, it must be replaced. Failure to follow this warning can result
in serious injury or death.
WARNING: All third-party mounting hardware should be corrosion-resistant and
designed for use where installed.
CAUTION:
Tighten the C-clamp pipe bolt to 15–20 ft./lbs. (approximately finger tight
plus up to one-quarter turn). Do not exceed 25 ft/lb. Do not use excessive
force.
Tighten the yoke pivot bolt to 5–10 ft/lb (approximately finger tight plus up
to one-eighth turn). Do not exceed 15 ft/lb. Do not use excessive force.

16 Desire D40/D60 XTI v1.8.2 User Manual
Safety Cable
The safety cable (or other approved safety device) should be attached to the fixture housing and
wrapped around the hanging structure (pipe). An appropriate attachment loop is provided on the
protruding tab of the fixture housing. Take care to leave as little slack as possible in the safety cable to
avoid the cable catching the yoke of the fixture.
Focus Adjustment
The fixture can be tilted up and down to focus the light where it is needed. Upon powering the fixture,
all colors are automatically on so you can focus the fixture. This preset remains active until it is changed
with an RDM configuration tool or DMX/RDM lighting control device.
Adjusting the Tilt
1. Loosen the yoke locking bolt.
2. With the fixture turned on, tilt it to the desired angle.
3. Tighten the yoke locking bolt.
Adjusting the Pan
The pan is adjusted at the hanging clamp or the mounting base. Consult the clamp manufacturer’s
documentation for instructions on loosening and rotating the yoke at the clamp or see the appropriate
installation instructions.
WARNING: The safety cable (or other approved safety device) must be securely attached
to the safety cable loop before loosening the clamp.
Safety
cable loop