elero Invio-868 User manual

elero GmbH
Antriebstechnik
Linsenhofer Str.59–63
D-72660 Beuren
[e-mail]
www.elero.com
Invio-868
Operating instructions
Please take care of the operating instructions!
Nr. 18 100.4901/0405309304 00
GB
elero

Safety instructions
GB-2
Risk of injury due to electrocution.
• The connections to the 230 V mains must be
made by authorised specialist personnel.
• De-energise the connection line prior to
installation.
• The regulations of the local energy supply
company as well as the regulations for wet
and damp rooms according to VDE 100 must
be followed when making the connections.
• Use only in dry rooms.
• Only use unmodified original elero electrical
parts.
• Keep persons away from the operating range
of the system.
• Keep children away from the controls.
• Follow the relevant country-specific
regulations.
• If one or more devices are used for controlling
the system, the operating range must stay
visible during operation
GB
Warning!
Safety instructions .......................................... GB-2
Explanation of buttons and display ....................... GB-3
General information ........................................ GB-4
Intended use................................................. GB-4
Installation/connection..................................... GB-5
Explanation .................................................. GB-6
Programming the radio .................................... GB-6
Programming the transmitter / channel ....... GB-6
Functions..................................................... GB-7
Intermediate position/ventilation position ..... GB-7
Approach intermediate position ................. GB-7
Approach ventilation/turning position.......... GB-7
Deletion of transmitter ..................................... GB-8
Deletion of transmitter........................... GB-8
Technical data ............................................... GB-9
Notes on troubleshooting .................................. GB-9
General conformity declaration ............................ GB-9
Contents
GB-1

General information/intended use
GB-4
General information
A venetian blind switch and/or a ProLine device can be
connected to the Invio-868 radio transmitter.
Intended use
The Invio-868 must only be used for controlling roller shutter,
awning and blind systems.
• Please ensure that the radio installations are not operated
in areas of heightened possible interference.
(e.g. hospitals, airports ...).
• The remote control is only approved for devices and systems
for which any malfunction of the manual transmitter or
receiver would not result in a risk for persons,animals or
property, or if such a risk is covered by other safety devices.
• The operator has no protection whatsoever from
interferences by other radio emitters and local terminals
(e.g. also from radio installations), that are normally used
on the same frequency range.
• Only use radio receivers with equipment and units approved
by the manufacturer.
Advice: Radio systems,which operate on the same frequency,
can lead to reception of interferences.
Please note, that the range of the radio signal is
limited by the government and the built
environment.
GB
Explanation of buttons and display
GB-3
Explanation of buttons and display
elero
v
P
BV
Terminals for
ProLine
devices
NNeutral conductor
LMains cable
vbTerminals for
keypads
n
n
v
n
n
n
v
Programming
button P
m
Transmission
indicator lamp
m

Explanation
GB-6
GB
Installation/connection
GB-5
vbTerminals for venetian blind switch
At these inputs you can connect a venetian blind switch.
VBTerminals for ProLine devices
It is possible to connect all potential-free devices to these
terminals. However only devices from the ProLine family can use
all the signals.
Advice: The connected ProLine devices must be calibrated as
DRIVE CONTROL DEVICES.
Programming the radio
Programming the transmitter/channel
Precondition: The Invio-868 must be installed. The switch or
another ProLine control device must also be
connected.
1. In the case of already-installed receivers,switch the fuse off
and then on again after a few seconds.
The receiver will now be in ready-to-program mode for
5 minutes
.
2. Now press the Pkey on the Invio-868 or on a manual
transmitter.
The receiver will now be in ready-to-program mode.
3. In order to define the key assignment,immediately after the
start of upward travel (1 sec.) press the UP key on the switch or
on the control device.
The roller shutter will stop for a short time.
Immediately after starting downward travel press the DOWN
key on the switch or on the control device.
The roller shutter will stop.
The Invio-868 has now been programmed.
2. Carry out the Invio-868 programming procedure at the
receiver (see Section entitled„Radio programming“).
3. Place the Invio-868 in the switchbox.
Advice: Make sure that the aerial is installed optimally.
Connection
The design for a control device can be found in the controller catalogue.
Warning!
Risk of injury due to electrocution!
•The connection must only be made by an authorized
specialist!
•The device only offers protection against touch by the back
of the hand (IP1X), no protection against accidental contact.
• Do not kink, shorten or extend the aerial..
• Only actuate the programming key P with an insulated tool
(4 kV proof voltage).
Precondition: Branch switchbox at 60 mm depth.
1. Connect the stripped cable ends without connector sleeves
as follows:
elero
Invio-868
LLN In In
ProLine
L
N
Mains
12345 6
Single Central
AstroTec
NL C
Mains
L
N
Venetian blind switch
230V/50Hz

Deletion of transmitter
GB-8
Deletion of transmitter
The Invio-868 can only be deleted with a programmed manual
transmitter
GB
Intermediate positions/ventilation position
GB-7
Intermediate positions/ventilation position
The intermediate or ventilation/turning position can only be
programmed with a ProLine control device or a manual
transmitter.
The intermediate or ventilation position cannot be programmed
with the roller shutter keypad.
Approach intermediate position
1. Press the DOWN button briefly twice successively.
2. The drive travels to the stored intermediate position.
If no intermediate position has been stored the roller shutter
travels to the lowest end position.
Approach ventilation/turning position
1. Press the UP button briefly twice successively.
2. The roller shutter travels to the stored ventilation position.
If no ventilation position has been stored the roller shutter
travels to the upper end position.

Warnhinweise
GB-10
Technical data/information for trouble-shooting/
general conformity declaration
GB-9
GB
Rated voltage 230-240 V AC / 50-60 Hz
Protection class IP 20
Permitted ambient temperature 0 to +55 °C
Radio frequency 868,3 MHz
Type of mounting Flush-mounted l58 mm
wall installation
Surface-mounted in
corresponding AP housing
Dimensions L 50 x W 48 x 22 mm
The maximum sending range within a building is up to 10 m.
Technical data
Notes on troubleshooting
Fault Cause Remedy
The drive does not False connection. Check connection.
run, the transmission
indicator lamp
doesn’t light up.
The drive does not 1. The receiver is outside 1. Reduce distance
run, the transmission of sending range. to the receiver.
indicator lamp stays 2. Transmitter not 2. Program the
on. programmed into transmitter.
receiver.
Drive operates in Incorrect direction has Delete transmitter
the wrong direction. been programmed. and program correctly.
General conformity declaration:
Herewith the company elero GmbH declares that the Invio-868
device satisfies the basic requirements and other relevant
regulations of the 1999/5/EC guidelines.