elero monotel 2 28 205.0001 User manual

MonoTel 2
No. 28205.0001, 28 206.0001,
28 207.0001
0709
NRG Automation Ltd.
Foundry Lane –
Halebank
Widnes,
CheshireWA8 8TZ
sales@
nrgautomation.co.uk
www.elero.com
elero Motors & Controls
Pvt. Ltd.
507,DDA Building II
District Centre Janak Puri
IND-New Delhi – 110058
Tel. [phone]
Fax [phone]
e-mail:[email protected]om
elero Singapore Pte.Ltd.
No.2,
Ang Mo Kio Street 64
#03-00 Ang Mo Kio
Industrial Park 3
SGP-Singapore 569084
Tel. [phone]
Fax [phone]
e-mail:
[e-mail]
elero GmbH
Antriebstechnik
Linsenhofer Str. 59–63
D-72660 Beuren
[e-mail]
www.elero.com
elero
Operating instructions
Please take care of the operating instructions!
GB

Device explanation
GB-2
GB
Device explanation ........................................ GB- 2
Safety instructions /exclusion of liability................ GB- 3
Bidirectional radio system scope of supply .............. GB- 5
Bidirectional radio system/unidirectional radio system GB- 6
Mounting of the wall bracket............................. GB- 8
Explanation of functions .................................. GB- 9
StatusLED.............................................. GB- 9
Groupcontrolunit..................................... GB- 9
Programming the transmitter............................. GB-10
Programming the transmitter / channel............. GB-10
Programming further transmitters................... GB-11
Approach limit positions of roller shutter/awning/
venetian blind.............................................. GB-12
Intermediate positions for roller shutters/awnings/
venetian blinds............................................. GB-13
Programintermediateposition....................... GB-13
Program ventilation/tilting position ................. GB-14
Approachintermediateposition...................... GB-14
Approach ventilation/tilting position ................ GB-14
Delete intermediate position ......................... GB-15
Delete ventilation/tilting position ................... GB-15
Deletion of transmitter.................................... GB-16
Deletion of individual transmitters .................. GB-16
Deletion of all transmitters........................... GB-16
Technical data .............................................. GB-16
Battery replacement....................................... GB-17
Cleaning .................................................... GB-17
Disposal..................................................... GB-17
Notes on troubleshooting................................. GB-18
Notes on repair............................................. GB-18
Repair address.............................................. GB-18
Contents
GB-1
elero
Fixing area for
wall bracket
Programming
button P
UP button
STOP button
Status LED
DOWN button
Battery
compartment
Back of equipment
on front of device

Safety instructions
GB-4
GB
Safety instructions/exclusion of liability
GB-3
STOP!
Observance of the operating instructions is the
prerequisite for disturbance-free operation and
fulfilment of any claims related to defects.
• Therefore,first read the operating instructions
before you use the device!
• Ensure that the operating instructions are
available to the user in legible form.
• The operator must ensure that the basic safety
measures are observed and fulfilled.
• The operator must have completely read and
understood the operating instructions.
• The following safety and installation instructions
solely refer to the transmitter and not the
accessories and drive.
Exclusion of liability:
It is essential to observe these operating instructions for use if the
MonoTel 2 hand-held transmitter is to be used safely and if the
various product characteristics and performance features are to be
achieved.
elero GmbH assumes no liability for personal injuries,property
damages and financial losses that arise from non-observance of
the operating instructions.
Liability for material defects is excluded in such cases.
CAUTION!
Observe the following safety instructions.
Failure to observe them can lead to bodily injuries!
General
• Never install or commission devices which are damaged.
• Only use unmodified original elero electrical parts.
• If the device is opened without permission or used in an
improper manner,or if it is incorrectly installed or
operated, there is a risk of damage to persons and
property.
• The device contains small parts which can be swallowed.
Transport
• If the transmitter arrives in a damaged condition despite
proper packaging, then it must not be commissioned.
Immediately report the damage to the transport
company.
Installation
• Note any country-specific conditions when installing the
device.
• The device may only be used by persons who have read
and understood the operating instructions.
Operation
• Use only in dry rooms.
• If one or more transmitters are used for controlling the
system,its operating range must stay visible during
operation.
• Keep children away from the control units.
• Replace battery only with identical type (LR06;AA).
• Dispose of used batteries properly (collection point).

GB-6
GB
Scope of supply/Intended use
GB-5
Manufacturing note
All the ProLine 2 transmitters are subject to 100% testing by elero
GmbH before delivery.
The ProLine 2 transmitters are made as per the following
guidelines:
• EN 300 220 (electromagnetic compatibility of radio systems)
• ETS 300 683 (Specific conditions for short range radio devices)
• CE mark
Scope of supply
MonoTel 2 (batteries (2 x LR 06; AA) supplied with device)
Wall bracket
2 dowels
2 screws
Intended use
The MonoTel 2 is a single-channel transmitter.This can be used
unidirectionally (compatible with the existing ProLine programme)
or bidirectionally.The hand-held transmitter may only be used for
controlling roller shutters, venetian blinds and sun protection
systems that are fitted with elero radio receivers.
Other use,or use which goes beyond this use is not considered to be
use for intended purpose.
elero GmbH shall not be liable for:
• Other uses than those described above
• Changes to the device
• Improper use
Please see the technical data contained in these operating
instructions.
Bidirectional radio system/
unidirectional radio system
What does bidirectional radio system mean?
A bidirectional radio system is one that carries out the reliable
transmission of radio signals to a radio receiver and provides
feedback from the radio receiver to the transmitter.
The radio signal can be sent directly to the target receiver. If this
is not possible then the radio signal is forwarded via other
participants until the signal reaches the target receiver.
The target receiver carries out the command and sends a
confirmation back to the transmitter.
The status LED lights up briefly for confirmation.
What is a unidirectional radio system?
A unidirectional radio system provides reliable transmission of
radio signals to a radio receiver.
However, the radio receiver cannot send back a reply to the
transmitter,unlike in a bidirectional radio system.
It is also not possible to pass on the radio signal from one radio
receiver to another.

GB-8
GB
Safety instructions for radio operation
GB-7
Mounting of the wall bracket
CAUTION!
Observe the following safety instructions for radio
operation!
Only use radio systems if they are approved and can be
operated without interference.
• Please note that radio systems must not be operated
in areas with an increased risk of interference
(e.g. hospitals, airports, ....).
• The remote control is only approved for devices and
systems for which any malfunction of the transmitter
or receiver would not result in a risk for persons,
animals or property, or if such a risk is covered by other
safety equipment.
• The operator has no protection whatsoever from inter-
ferences by other radio emitters and local terminals
(e.g. also from radio systems), that are normally used
on the same frequency range.
• The range of the radio signal is limited by the
government and the built environment.
Mounting of the wall bracket
1. Use the drilling template on the inside of the packing box.
2. Remove the cover from the box.
3. Fix the drilling template to the wall.
4. Drill the holes in the wall.
5. Remove the drilling template.
6. Push the bracket upper and lower parts to separate them.
7. Fix the bracket lower part onto the wall using the screws and
dowels provided.
8. Push the bracket upper part from above onto the bracket lower
part until it is locked into place.
4,5
10, 5 24,75
4,5
4,5
13, 5
NOTICE!
The wall bracket has to be fixed so that the drill
holes don’t touch any electrical lines.
Check this before installation.
Bracket upper part
Bracket lower part

Programming the transmitter
GB-10
Status LED
A radio signal is displayed by the illumination of the Status LED
(LED ring around the STOP button).
The status LED can display three different colours:
– Orange: Transmit signal is being sent
(bidirectional radio operation)
– Green: Transmit signal is being sent
(unidirectional radio operation)
Positive reply from the transmitted signal
(bidirectional radio operation)
– Red: No answer from receiver
(bidirectional radio operation)
The transmitting power or the radio range will be reduced
through the reduction in the performance of the battery.
If the status LED no longer illuminates upon pressing the button,
the batteries have to be replaced.
Please see these instructions for changing the battery.
(Wsee battery replacement)
Group control unit
A group is understood to mean the control of several receivers
at the same time.The selected group is controlled by a travel
command.
With the MonoTel 2 the radio channel can be used to control a
group.
GB
Explanation of functions
GB-9
1. With electrical, previously installed receivers, turn the safety
fuse off and after a few seconds on again.
The receiver is now in programming mode for about 5 minutes.
2. Press the programming button Pon the back of the device
briefly (approx 1 sec).
The shutter/blind moves up and down automatically after
approx. 2 minutes to show that the receiver is in programming
mode.
3. Press the UP button immediately after the start of upward
travel (max. 1 second).
The status LED lights up briefly.
The blind will stop – start moving again – stop and then move
in the DOWN direction.
4. Press the DOWN button immediately after the start of
downward travel (max. 1 second).
The status LED lights up briefly.
The blind/shutter will stop.
The MonoTel 2 is now programmed.
Programming the transmitter
PREREQUISITE!
The receiver must be installed.
Note that the radio range to the receiver is limited
during programming.
Position yourself in front of the shutter/blind for
programming.
!
NOTICE!
If the blind does not stop, the programming process
must be repeated.

GB-12
GB
Programming additional transmitters
GB-11
Programming additional transmitters
NOTICE!
If several receivers are connected to the same feed
line, then all are simultaneously ready to program.
The blinds start a“random”brief up/down travel.
The longer you wait with the programming the
greater will be the offset.
You can stop the brief up/down travel by briefly
pressing the STOP button on a transmitter which
has already been programmed.The programming
procedure is interrupted.
The transmitter assignment can now be made
without having to disconnect individual receivers.
If the blind travels in the wrong direction, delete the
transmitter and reprogram it.
(Wsee Deletion of transmitter)
To programme additional transmitters in one receiver,please proceed
as follows:
1. Press the UP, DOWN and the programming button P(back of
device) simultaneously (for 3 sec.) on a transmitter,which has
already been programmed to the receiver.The status LED lights up
briefly.
Push the programming button P(on back of device) on the new
transmitter to be programmed until the status LED lights up briefly.
2. Press the UP button immediately after the start of upward travel
(max. 1 second).
The status LED lights up briefly.The blind will stop – start moving
again – stop and then move in the DOWN direction.
3. Press the DOWN button immediately after the start of downward
travel (max.1 second).
The status LED lights up briefly.The blind will stop.
The transmitter or the transmitter channel has been programmed.
Approach limit positions
Roller shutter/awning/venetian blind
PREREQUISITE!
The transmitter/transmitter channel has been
programmed.
The end positions of the drive have been set.
!
Approach lower end position (roller shutter/awning)
Press the DOWN button briefly.
The blind approaches the lower end position/the awning moves
out.
Approach lower end position (venetian blind)
Press the DOWN button until the status LED lights up briefly.
The blind approaches the lower end position.
Press the DOWN button briefly (jogging mode); the blind moves a
short distance and stops again.
Approach upper end position (roller shutter/awning)
Press the UP button briefly.
The blind approaches the upper end position/the awning retracts.
Approach upper end position (venetian blind)
Press the UP button until the status LED lights up briefly.
The blind approaches the upper end position.
Press the UP button briefly (jogging mode); the blind moves a
short distance and stops again.

GB-14
GB
GB-13
Intermediate positions for roller shutters/
awnings/venetian blinds
Program intermediate position
1. Move the blind as far as necessary in the UP direction until the
ventilation gaps open or the slats are inverted.
Hold down the UP button until the desired position is reached.
2. In addition press the STOP button.
The blind/shutter will stop.The status LED lights up briefly.
The intermediate position/ventilation position is now
programmed.
Roller shutters Awning Venetian blind
Pos BIntermediate Intermediate Intermediate
position position position
Pos VVentilation position – Tilting position
PREREQUISITE!
The transmitter/transmitter channel has been
programmed.
The end positions of the drive have been set.
The blind/shutter is at its upper end position.
!
Intermediate positions for roller shutters/
awnings/venetian blinds
Program ventilation/tilting position
1. Move the blind as far as necessary in the UP direction until the
ventilation gaps open or the slats are inverted.
Hold down the UP button until the desired position is reached.
2. In addition press the STOP button.
The blind/shutter will stop.The status LED lights up briefly.
The intermediate position/ventilation position is now pro-
grammed.
PREREQUISITE!
The transmitter/transmitter channel has been
programmed.
The end positions of the drive have been set.
The blind/shutter is at its lower end position.
!
PREREQUISITE!
The transmitter/transmitter channel has been
programmed.
!
Approach intermediate position
1.
Press the DOWN button briefly twice.The status LED lights up
briefly.
2. The blind travels to the stored intermediate position.
In the case of venetian blinds,after reaching the intermediate
position, the slats turn automatically.
If no intermediate position has been programmed the
blind/shutter travels to the lower end position.
PREREQUISITE!
The transmitter/transmitter channel has been
programmed.
!
Approach ventilation/tilting position
1.
Press the UP button briefly twice.The status LED lights up briefly .
2.
The blind/shutter travels to the stored ventilation/tilting position.
If no ventilation/tilting position has been programmed the
blind/shutter travels to the upper end position.

GB-15 GB-16
GB
Delete positions
Delete intermediate position
1. Press the STOP button and also the DOWN button.
2. Hold down this button combination for approx. 3 sec.
The status LED lights up briefly.
Delete ventilation/tilting position
1. Press the STOP button and also the UP button.
2. Hold down this button combination for approx. 3 sec.
The status LED lights up briefly.
Delete transmitter/channel
1. Press the STOP button and also the programming button P
(back of unit).
2. Hold down this button combination for approx. 6 seconds until
the status LED lights up briefly orange and then red.
In the unidirectional radio operation the status LED lights up
green briefly twice and then orange during the 6 seconds.
Deletion of all transmitters
1. Press the STOP button and also:
• Programming button P(on back of device)
• UP button
• DOWN button
2. Hold down this button combination for approx. 6 sec.
The status LED lights up briefly twice.
In the unidirectional radio operation the status LED lights up
green briefly twice and then orange during the 6 seconds.
Technical data
Operating voltage 3 V DC
Battery type 2 x LR 06 (AA cells)
Protection class IP 20
Permitted ambient temperature 0 to +50°C
Radio frequency 868 MHz frequency band
Dimensions in mm L 120 x W 51 x H 26
Delete transmitter/technical data

GB-18
GB
GB-17
Battery changing/cleaning/disposal
Battery replacement
NOTICE!
• Replace batteries only with identical type
(2 x LR 06; AA cells).
• Dispose of used batteries properly
(collection point).
1. Unscrew the hand-held transmitter using
a suitable screwdriver on the underside of
the device and remove the cover.
2. Remove the batteries.
3. Insert the new batteries (2 x LR 06; AA cells)
correctly in the transmitter.
4. Place the cover on the housing again and screw
on tightly with the screwdriver.
Cleaning
Clean the device with a damp cloth.
Don’t use any cleaning agents.This may attack the plastic.
Disposal
Please observe the current national regulations. Dispose of
according to the condition and existing regulations.
e.g. as:
• Electrical scrap (PCB)
• Plastic (Housing parts)
• Batteries
Troubleshooting/repair
Notes on troubleshooting
Fault Cause Remedy
The drive does 1. Batteries are low. 1. Replace batteries.
not run, the status
LED does not 2. Batteries are 2. Insert batteries
light up. incorrectly installed. correctly.
The drive does 1. The receiver is outside 1. Reduce distance
not run, the status the radio range. to the receiver.
LED lights up red. 2. Receiver out of 2. Switch on or
order or faulty. exchange receiver.
Drive operates in Directions are Delete transmitter
the wrong direction. incorrectly allocated. and reprogram.
Notes on repair
Please contact us if you are unable to eliminate a problem.
When contacting our service team, please always state the item
description and number from the type plate (back of device).
– Item number – Accompanying conditions
– Item description – Own presumption
– Type of fault – Previously occurring unusual
events
Repair address:
elero GmbH
Antriebstechnik
Linsenhofer Straße 59–63
D-72660 Beuren
Telephone [phone] Please visit us on the Internet
Fax [phone] if you require a contact outside
www.elero.com Germany.