elero LumeroTel User manual

LumeroTel
Nr. 28221.0001
Operating instructions
Please keep these instructions in a safe place!
Operating Instructions
Please keep the instructions in a safe place.
Notice de service
Prière de conserver cette notice de service !
Manual de instrucciones
¡Por favor guarde estas instrucciones!
Istruzioni per l'uso
Conservare le istruzioni!
Instrukcja obs∏ugi
Instrukcj´ nale˝y zachowaç !
Nr.18 100.4001/0204
GB
GB
FR
ES
IT
PL
309401
elero
elero Latinoamérica
Av.Brasil 2476 Of.202
11300 Montevideo
URUGUAY
[e-mail]
www.elero.com

Safety instructions
GB-2
Important safety instructions!
The following instructions must be observed
at all times.
• For use in dry rooms only.
• Use unmodified elero original parts only.
• Keep persons away from the systems guide
track.
• Keep children away from controls.
• Always comply with national stipulations.
• Always dispose of used batteries properly.
Always replace batteries with identical type
(LR 03; AAA).
• If the system is controlled by one or more
transmitters, the system guide track must be
visible during operation.
• The equipment contains small parts that could
be swallowed.
GB
Warning!
Safety instructions......................................... GB- 2
Explanation of buttons .................................... GB- 3
General information ....................................... GB- 4
Designated use............................................. GB- 4
Notes........................................................ GB- 5
Wall holder installation ................................... GB- 5
Explanation of functions .................................. GB- 6
Manual/Automatic sliding switch .................... GB- 6
Transmission control light ............................ GB- 6
Group control .......................................... GB- 6
Programming radio channel settings..................... GB- 7
Programming transmitter/channel................... GB- 7
Programming additional transmitters ............... GB- 7
Intermediate position for roller shutter/awning/
venetian blind.............................................. GB- 9
Programming intermediate position ................. GB- 9
Programming ventilation/reverse position .......... GB- 9
Adjustment to intermediate position ................ GB-10
Adjustment to ventilation/reverse position ......... GB-10
Deleting intermediate position....................... GB-10
Deleting ventilation/reverse position ................ GB-10
Deleting radio channel settings........................... GB-11
Deleting individual transmitters ..................... GB-11
Deleting all transmitters.............................. GB-11
Technical data .............................................. GB-12
Cleaning .................................................... GB-12
Battery replacement....................................... GB-12
Troubleshooting............................................ GB-12
General declaration of conformity........................ GB-12
Contents
GB-1

GB-4
General information
The LumeroTel handheld transmitter can be used to operate
one or more receivers.
This device is characterised by its user-friendly operation.
Designated use
The LumeroTel device may be used to operate roller
shutters/sun protection systems only.
• Please note that radio-controlled systems may not be used in
areas with a high risk of interference (e.g. hospitals,airports).
• The remote control is intended solely for use with equipment
and systems in which malfunctions in the handheld
transmitter or receiver would not pose any risk to persons,
animals or property or which contain safety devices to
eliminate such risks.
• The operator is not protected from interference from other
telecommunications systems and terminal equipment
(e.g. even from radio-controlled systems which are properly
operated in the same frequency range).
• Radio receivers may only be used in combination with
equipment and systems stipulated in manufacturers’
specifications.
GB
elero
Auto
Explanation of buttons
GB-3
Manual/Automatic
sliding switch
Transmission
control light
Programming
button P
vUP button
ySTOP button
bDOWN button
Battery
compartment
Labelling fields
General information/Designated use

Explanation of functions
GB-6
Manual/Automatic sliding switch
The sliding switch is used to switch the receivers into either
“MANUAL ”or“AUTO” mode.
When the sliding switch is set to automatic mode, the
receivers will respond to every signal transmitted,whereas in
manual mode they will only respond to UP,STOP and DOWN
control commands,as well as to wind alarm signals.
Transmission control light
The transmission control light is illuminated when a radio
signal is being transmitted.
The transmission control light will flash during transmission if
battery power is low.
The transmission power or radio operating range will decrease
as battery power decreases.If the transmission control light
does not light up when the buttons are pressed,the batteries
must be replaced.
Group control
Group control refers to the operation of one or more receivers
at the same time.The group selected is controlled via a control
command.
The LumeroTel operates the chosen group via a radio channel.
Note: The inlay card beneath the transparent cover can be
used to make a note of the groups which have been
programmed.
GB
Installation
GB-5
Note: Radio base stations transmitting in the same frequency
range may cause reception interference.
Please note that the operating range of the radio signal
is limited by legislation as well as by the product design.
Wall holder installation
• Before installing the wall holder, always ensure that the
transmitter and receiver are in proper working order.
• Mount the holder onto the wall using the two raw plugs and
screws provided.

GB-8
GB
Programming radio channel settings
GB-7
Programming transmitter/channel
Prerequisite: The receiver must be installed.
1. With pre-installed electric receivers, the fuse must be
disconnected and reconnected after a few seconds.The receiver
will remain in programming mode for approximately 5 minutes.
2. Position yourself in front of the roller shutter/awning/blind with
the remote control in your hand.
3. Open the front cover of the device and press the transmitter pro-
gramming button Pbriefly.The shutter/awning/blind will start to
move up and down.This will happen for approximately 2 minutes.
4. To define the keyboard layout,press the UP button on the trans-
mitter as soon as the shutter/awning/blind begins to move
upwards (after approx. 1 second).The shutter/awning/blind will
come to a halt briefly.
As soon as the shutter/awning/blind begins to move again,press
the DOWN button on the handheld transmitter.
The shutter/awning/blind will come to a stop.
The transmitter or this channel has been successfully programmed.
Programming radio channel settings
Programming additional transmitters
To programme additional transmitters in one receiver, please proceed
as follows:
1. Press the UP,DOWN and programming button Pon a transmitter
that has already been programmed in the receiver until the LED
goes out.
2. To define the keyboard layout,press the UP button on the handheld
transmitter as soon as the shutter/awning/blind begins to move
upwards (after approx.1 second).
The shutter/awning/blind will come to a halt briefly.
As soon as the shutter/awning/blind begins to move again,press
the DOWN button on the handheld transmitter.
The shutter/awning/blind will come to a stop.
The transmitter or this channel has been successfully programmed.
Note: If more than one receiver is connected to the same supply
lead, all of these will be in programming mode
simultaneously.The shutters/awnings/blinds will begin to
move up and down“at random”.The longer you take to
carry out the programming, the larger the offset will be.
Individual channels can now be assigned to the given
receiver.
To stop the brief up and dpwn movements, press the
STOP button on one of the pre-programmed handheld
transmitters briefly.
Channel assignment /modification can now be carried out
without you having to disconnect individual receivers.
If the shutter/awning/blind moves in the wrong direction,
the transmitter must be deleted and re-programmed.

GB-9
Intermediate position for roller
shutter/awning/venetian blind
Programming Pos B
Prerequisite: The transmitter has been programmed and the
end limit positions have been set.The curtain/
canopy/blind is in the upper end limit position.
1. Adjust the curtain/canopy/blind into the desired position
using the DOWN button.
Note: Keep the DOWN button pressed until the desired posi-
tion is reached.
2. When the curtain/canopy/blind has reached the desired
position, press the STOP button in addition.
The curtain/canopy/blind will come to a stop.The
intermediate position has been successfully programmed.
Programming Pos V
Prerequisite: The transmitter has been programmed and the
end limit positions have been set.The curtain/
canopy/blind is in the lower end limit position.
1. Move the curtain/canopy/blind in the UP direction using
the handheld transmitter until the ventilation slits are open
or the reverse position has been reached.
Note: Keep the UP button pressed until the desired position
is reached.
2. When the curtain/canopy/blind has reached the desired
position, press the STOP button in addition.
The curtain/canopy/blind will come to a stop.The venti-
lation/reverse position has been successfully programmed.
GB-10
GB
Intermediate position for roller
shutter/awning/venetian blind
Adjustment to Pos B
Prerequisite: The transmitter has been programmed.
1. Press the UP button twice in quick succession.
2. The drive will adjust the curtain/canopy/blind into the stored
intermediate position.If no intermediate position is stored,the
curtain/canopy/blind is automatically adjusted into the lower
limit position.
Adjustment to Pos V(roller shutter, awning)
Prerequisite: The transmitter has been programmed.
1. Press the UP button twice in quick succession.
2. The curtain/canopy is adjusted into the stored ventilation
position. If no ventilation position is stored,the curtain/canopy
is automatically adjusted into the upper limit position.
Adjustment to Pos V(venetian blind)
Prerequisite: The transmitter has been programmed.
1. Press the UP button twice in quick succession.
2. The blind is adjusted into the stored reverse position. If no
reverse position is stored, the blind is automatically adjusted
into the lower limit position.
Deleting Pos B
1. Press the following buttons simultaneously:
• DOWN button
• STOP button
2. Keep these two buttons pressed until the LED goes out briefly.
Deleting Pos V
1. Press the following buttons simultaneously:
• UP button
• STOP button
2. Keep these two buttons pressed until the LED goes out briefly.
Roller shutter Awning Venetian blind
Pos BIntermediate Intermediate Intermediate
position position position
Pos VVentilation position Canopy tension Reverse position

GB-12
GB
Operating voltage 3 V DC
Battery requirements 2 x LR 03 (AAA)
System of protection IP 20
Permissible ambient temperature –10 to +55 °C
Operating frequency 433,92 MHz AM
Dimensions in mm L 121 x W 43 x H 23
Deleting individual transmitters
Disconnect the fuse – and reconnect after a few seconds.
1. Open the front cover on the device and press the following
buttons simultaneously:
• Programming button P
• STOP button
2. Keep these two buttons pressed until the LED goes out briefly.
Deleting all transmitters
Disconnect the fuse – and reconnect after a few seconds.
1. Open the front cover on the device and press the following
buttons simultaneously:
• Programming button P
• UP button
• STOP button
• DOWN button
2. Keep these buttons pressed until the LED flashes 3 times.
Technical data
The maximum radio operating range is 25 m indoors and 350 m
outdoors.
GB-11
Deleting radio channel settings/
Technical data Battery replacement/Cleaning/
Troubleshooting
Battery replacement
1. Open the battery compartment.
2. Remove the batteries.
3. Insert the new batteries properly.
Cleaning
Clean the device with a damp cloth only.
Do not use a cleansing agent as doing so may damage the
plastic.
Troubleshooting
Problem Cause Remedy
Drive is not functioning. 1. Batteries are empty. 1. Replace batteries
Transmission control 2. Batteries are inserted 2. Remove batteries
light is not illuminated. incorrectly. and re-insert
properly.
Drive is not functioning. 1. Receiver is not within 1. Move receiver closer
Transmission control radio operating range. to ensure it is within
light is illuminated. operating range.
2. Transmitter is not 2. Programme
programmed in receiver. transmitter.
Transmission control Battery power is low. Replace batteries.
light is flashing.
Automatic switching The LumeroTel is in Adjust the LumeroTel
commands are not “MANUAL ”mode. to“AUTO”mode.
carried out.
Drive moves in wrong The directions have been Delete transmitter and
direction. set incorrectly. re-programme correctly.
General declaration of conformity:
The company elero GmbH hereby declares that the LumeroTel
handheld transmitter complies with the basic requirements and
other relevant regulations of the EC Directive 1999/5/EG.

GB-14
GB
GB-13