Elite Screens Osprey Tension Dual Series Guide

Osprey Tension Dual Series Limit Switch Adjustment Instructions
Caution: The screen’s Top Black Drop is already set to its maximum drop distance. There is NO
extra black top drop in the roller. Attempting to increase the drop will damage the motor and VOID
your warranty with Elite Screens. DO NOT use these instructions to try and get more out of your
standard black masking drop. Please contact Elite Screens before making any adjustments.
1. Allen Wrench
2. Screens
5/32” Allen wrench
First screen (2.35:1)
Second screen (16:9)

3. Limit Switch Adjustment Locations
(NOTE: When turning the limit switches, bear in mind that a full‐circle turn in either
direction will create a one inch adjustment)
4. Adjusting the Retract Position for the second screen (16:9)
Up adjustment switch for the second screen (16:9)
UP adjustment switch
Down adjustment switch for the second screen (16:9)
Down adjustment switch for the first screen (2.35:1)
Note: Inside of case
Up adjustment switch for the first screen (2.35:1)
If the second screen will not retract
completely (as shown in Fig.3), use
the following steps.
Use the remote to retract the screen as much
as possible by pressing the UP button.

5. Adjusting the Top Black Masking for the second screen (16:9)
Note: Top Black Masking should only be increased if you previously decreased the drop
and want it back. The screen’s Top Black Drop is already set to its maximum drop
distance. There is NO extra black top drop in the roller. Do not attempt to increase
more black drop as the screen material will come off the roller and void your warranty.
Use your allen-wrench to turn the
UP switch counter-clockwise.
When you turn the UP switch, the
screen will retract correspondingly.
Stop rotating the switch once the
weight bar lines up with the casing.
(WARNING: If you continue to rotate
the switch once the weight bar fits flush
with the casing, the screen will attempt
to retract further, causing damage to
the unit. DO NOT over turn the switch.)
If the screen retracts too far,
just rotate the UP adjustment
switch 2-3 turns clockwise,
and the screen will lower.

If you need to increase the
amount of top black masking,
refer to the following steps.
Use your remote control to fully lower
the screen by pressing the 16:9 button.
Use your allen-wrench to
turn the DOWN switch
counter-clockwise.
When you turn the DOWN switch, the
screen will lower correspondingly. Stop
turning the switch once the screen
reaches the desired position.
(WARNING: If you over-turn the switch,
the screen will lower completely and
damage the unit.)

6. Adjusting the Retract Position for the first screen (2.35:1)
If the screen lowers too much,
simply rotate the DOWN
adjustment switch clockwise, the
screen will retract into its casing.
(NOTE: Please avoid over-turning
the switch.)
If the first screen will not retract
completely (as shown in Fig.3), use
the following steps.
Use the remote to retract the screen
as much as possible by pressing the
UP button.
Use your allen-wrench to turn the
UP switch counter-clockwise.

7. Adjusting the Top Black Masking for the first screen (2.35:1)
Note: Top Black Masking should only be increased if you previously decreased the drop
and want it back. The screen’s Top Black Drop is already set to its maximum drop
distance. There is NO extra black top drop in the roller. Do not attempt to increase
more black drop as the screen material will come off the roller and void your warranty.
When you turn the UP switch, the
screen will retract correspondingly.
Stop rotating the switch once the
weight bar lines up with the casing.
(WARNING: If you continue to rotate
the switch once the weight bar fits flush
with the casing, the screen will attempt
to retract further, causing damage to
the unit. DO NOT over turn the switch.)
If the screen retracts too far in, just
rotate the UP adjustment switch
2-3 turns clockwise, and the
screen will lower.
If you need to increase the
amount of top black masking,
refer to the following steps.

Note: As a rule, Elite Screens does not recommend making any
unnecessary adjustments to the screen, as improper adjustments will
damage the unit.
Use your remote control to
fully lower the screen by
pressing the 2.35:1 button.
Use your allen-wrench to
turn the DOWN switch
counter-clockwise.
When you turn the DOWN switch,
the screen will lower
correspondingly. Stop turning the
switch once the screen reaches the
desired position. (WARNING: If you
over-turn the switch, the screen will
lower completely and damage the
unit.)
If the screen lowers too much,
simply rotate the DOWN
adjustment switch clockwise, the
screen will retract into its casing.
(NOTE: Please avoid over-turning
the switch.)