SPECIFICATION DATA
Tensioned LARGe AdvAnTAGe
®
deLuxe eLecTRoL
®
Automatic Electric Projection Screen Model
VIDEO (NTSC 4:3) FORMAT DIMENSIONS
Viewing Area Nominal Diagonal Overall Length of Case (does not include flange) Approx. Ship. Wt.
H x W Cm In. Cm In. Cm Lbs. Kg
126" x 168" 320 x 427 210" 533 199¼" 506 628 284.9
132" x 176" 335 x 447 220" 559 208¼" 529 655 297.1
144" x 192" 366 x 488 240" 610 225¾" 573 708 321.1
162" x 216" 411 x 549 270" 686 251¼" 638 781 354.3
S
UGGESTED SPECIFICATIONS: projection screen(s), (H) x ( W ) .
The Tensioned
Advantage®Deluxe screen shall have two motors, one to operate door and one to operate screen. Door motor electrically operated 120 volt
(60 Hz) not more than 1.2 amp. Shall have motor mounted inside the roller, to be three wire with ground, quick reversal type, oiled for life,
with automatic thermal overload cutout, integral gears, capacitor and an electric brake to prevent coasting. To have pre-set but adjustable
limit switches to automatically stop fabric door in the ”down“ position. The door will lift to the closed position where a micro switch shall
cut off the electrical current to the door motor. The roller to be of 1.6" diameter aluminum. Screen motor is electrically operated 120 volt (60
Hz) not more than 2.4 amp. Shall have motor mounted inside the roller, to be three wire with ground quick reversal type, oiled for life, with
automatic thermal overload cutout, integral gears, capacitor and an electric brake to prevent coasting. To have pre-set but adjustable limit
switches to automatically stop picture surface in the ”up“ and ”down“ positions. The fabric roller to be of 4½" diameter (5¾" if 270" diagonal,
275" diagonal, or 298" diagonal) metal. Screen fabric to be seamless, flame retardant and mildew resistant vinyl, with black masking borders
standard. Each side of the fabric to have tab guide cable system to maintain even lateral tension and hold surface flat. Custom slat bar with
added weight maintains vertical tension on the screen surface. The ends of the slat to be protected by heavy duty plastic caps enclosing a
preset adjustable mechanism for screen tensioning. Case shall be a white powder coated extruded aluminum. Bottom of case to be self-
trimming with a built-in flange around the bottom of the case. A section of the bottom of the case shall be a retractable aluminum door
that opens and closes automatically with the lowering and raising of the picture surface. The balance of the bottom of the case shall be a
second hinged aluminum door with manual opening to provide access. Hinges shall be mounted in a concealed way. Junction box shall be
internally integrated into the housing making it possible to install the housing and wire to the building’s electrical system during construction.
The junction box shall contain a quick connect connector that is mounted in the housing for easy plug-in connection to the motorized fabric
and roller assembly. The motorized fabric and roller assembly to be installed in the case at the factory or at a later time at the job site. To
be complete with integrated low voltage control unit and three position control switch with cover plate. Suitable for use in environmental
air space in accordance with section 300-22 (c) of the National Electric Code, and sections 2-128, 12-010 (3) and 12-100 of the Canadian
Electrical Code, part 1, CSA C22.1. Screen to be listed by Underwriters’ Laboratories.
All viewing surfaces will be seamless.
All viewing surfaces are standard with black backing except Da-Tex®and Dual Vision.
HDTV (16:9) FORMAT DIMENSIONS
Viewing Area Nominal Diagonal Overall Length of Case (does not include flange) Approx. Ship. Wt.
H x W Cm In. Cm In. Cm Lbs. Kg
108" x 192" 274 x 488 220" 559 220¾" 561 688 312.1
121" x 216" 307 x 549 247" 627 2461⁄2" 627 764 346.5
135" x 240" 343 x 610 275" 699 2721⁄2" 693 841 381.5
146" x 260" 371 x 660 298" 757 294¼" 747 870 394.6
SQUARE FORMAT DIMENSIONS
Viewing Area Overall Length of Case (does not include flange) Approx. Ship. Wt.
H x W Cm In. Cm Lbs. Kg
10'6" x 14' 320 x 427 199¼" 506 628 284.9
14' x 14' 427 x 427 205¾" 523 655 297.1
12' x 16' 366 x 488 225¾" 573 708 321.1
All screens standard with 12" black drop at top, except 270" diagonal, which has 2".
Extra drop may alter case dimensions. Contact Da-Lite for details.
Overall case length dimensions ±¼" (6mm).
Detail dimensional drawings, wiring diagrams and installation instructions available upon request.
Specifications subject to change without notice.
Custom formats and sizes available upon request.
WIDE (16:10) FORMAT DIMENSIONS
Viewing Area Nominal Diagonal Overall Length of Case (does not include flange) Approx. Ship. Wt.
H x W Cm In. Cm In. Cm Lbs. Kg
110" x 176" 279 x 447 208" 528 205" 521 691 313.4
120" x 192" 305 x 488 226" 574 2221⁄4" 565 729 330.7
DA-LITE SCREEN COMPANy LLC
3100 North Detroit Street
Post Office Box 137
Warsaw, Indiana 46581-0137
P 800-622-3737 / 574-267-8101
F 877-325-4832 / 574-267-7804
www.da-lite.com
