Elkay FLEXI-GUARD EIOA4 1E Series Installation manual

97756C (Rev. G - 9/03)
EIOA4*1E EIOA8*1E EIOATL8*1E EIOA8*3EJO
PAGE 1
With FLEXI-GUARD®
Installation/Care/Use Manual
USES HFC-134A REFRIGERANT
FIG. 1
19
35
18
SEE FIG. 4
47, 48, 49, 50, 51
18
39, 40, 41
38
34
52
26, 27
46
21
20
22, 23, 24, 25
SEE FIG. 3
36
18
12 42
43, 44, 45
37
54
53
28
All manuals and user guides at all-guides.com
all-guides.com

97756C (Rev. G - 9/03)
EIOA4*1E EIOA8*1E EIOATL8*1E EIOA8*3EJO
PAGE 2
FIG. 2
FINISHED FLOOR PISO ACABADO PLANCHER FINI
*ADA REQUIREMENT *REQUISITO DE A.D.A. *EXIGENCE ADA
D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX
CAJA RECESIVA DEALAMBRES (3) DE SUMINISTRO ELÉCTRICO BOÎTE ENCASTRÉE DALIMENTATION ÉLECTRIQUE (3) FILS
E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO
WALL.
ASEGURE UNA VENTILACIÓN ADECUADA MANTENIENDO UN ESPACIO E 6" (152 mm) (MÍN.) DE HOLGURA ENTRE LA REJILLA DE VENTILACIÓN DEL MUEBLE Y LA PARED ASSUREZ-VOUS UNE BONNE VENTILATION EN GARDANT 6" (152 mm) (MIN.) ENTRE LES ÉVENTS DE LENCEINTE ET LE MUR.
F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
AGUJEROS DE LAS TUERCAS DE 7/16 PARA SUJETAR LA UNIDAD A LA PARED TROUS DÉCROUS 7/16 POUR FIXER LAPPAREILAU MUR
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB 1-1/2 IN. (38 mm) OUT
FROM WALL SHUT OFF BY OTHERS
SE RECOMIENDA UBICAR ELTUBO CORTO DE CONEXIÓN AL TUBO DE COBRE SIN CHAPAR DE 3/8" DE DIÁM. EXT. A1-1/2"
(38 mm) FUERA DE LALLAVE DE PASO EN LA PARED COLOCADAPOR TERCEROS.
EMPLACEMENT RECOMMANDÉ D'ALIMENTATION EN EAU PAR TUBE EN CUIVRE NON PLAQUÉ DE 3/8 PO. (9,5 mm) D.E.
CONNECTANT UNE TUYAUTERIE DE 1-1/2 PO. (38 mm) DEPUIS LE ROBINET D'ARRÊT FOURNI PAR D'AUTRES.
B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/4 O.D. DRAIN
UBICACIÓN RECOMENDADA PARA EL DRENAJE DE SALIDADEAGUA, DE 1¼ DE DIÁMETRO. EMPLACEMENT RECOMMANDÉ POUR LE DRAIN DE D.E. 1-1/4" DE SORTIE DEAU.
C = 1-1/4 TRAP NOT FURNISHED**
PURGADOR DE 1¼ NO PROPORCIONADO** SIPHON 1-1/4 NON FOURNI**
All manuals and user guides at all-guides.com

97756C (Rev. G - 9/03)
EIOA4*1E EIOA8*1E EIOATL8*1E EIOA8*3EJO
PAGE 3
SENSOR RANGE ADJUSTMENT: The electronic sensor used in this cooler is factory pre-set for a "visual" range of 36
inches (914 mm). If actual range varies greatly from this or a different setting is desired, follow the range adjustment
procedure below:
A. Remove front panel of cooler.
B. Using a small tip screwdriver, rotate range adjustment screw clockwise to increase range and counterclockwise to
decrease range (See Fig. 3).
CAUTION: Complete range of sensor (24-46 inches/610-1168mm) is only one turn of the adjusting screw.
C. Replace front panel.
SENSOR CONTROL: If sensor fails to operate valve mechanism or operates erratically, check the following.
A. Ensure there are no obstructions within a 40 inch (1016mm) radius in front of cooler.
B. Check wire connections at the solenoid valve and sensor. CAUTION: Make sure unit is unplugged before checking any
wiring.
C. Ensure proper operation of solenoid valve. If there is an audible clicking sound yet no water flows, look for an obstruction
in the valve itself or elsewhere in the water supply line.
13
NOTE: WATER FLOW DIRECTON
RANGE
ADJUSTMENT
SCREW
7
14
10
6
14
FIG. 3
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by re-
moving one (1) screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add
fixture support carrier if wall will not provide adequate sup-
port.
IMPORTANT:
7-3/4 in. (197mm) dimension from wall to centerline of
trap must be maintained for proper fit.
Anchor hanger securely to wall using all six (6) 1/4 in. dia.
mounting holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the
hanger bracket is engaged properly in the slots on the
cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at
the bottom of cooler base and two (2) screws at the top.
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instruc-
tions.
7) Remove the slip nut and gasket from the trap and install
them on the cooler waste line making sure that the end of
the waste line fits into the trap. Assemble the slip nut and
gasket to the trap and tighten securely.
START UP
Also See General Instructions
8) Stream height is factory set at 35 PSI. If supply
pressure varies greatly from this, adjust screw, ac-
cessible by removing front panel (Item 7, Fig. 3).
CW adjustment will raise stream and CCW adjust-
ment will lower stream. For best adjustment, stream
should hit basin approximately 6-1/2 (165mm) from
bubbler.
9) Replace the front panel and secure by retightening
four (4) screws.
ITEM NO. PART NO.
Panel-Bottom Dispenser
Bracket-Valve Mounting
Sensor-Clear (115V)
Sensor-Clear (230V)
Solenoid Valve (115V)
Solenoid Valve (230V)
Panel-Right Side
Panel-Left Side
Panel-Front
Elbow 1/4 Stem x 1/4 O.D.
Fitting 1/4 NPTF x 1/4 O.D.
Nut-Regulator
Screw-#6-32 x 1/2" Lg. PHMS
Screw-#10 x 1/2" Lg. THSM
Hex Nut
Screw-#8 x 5/8" Lg. Torx/Slot
Regulator
Holder-Regulator
Screw-#10 x 1/2" Lg. HHSM
22897C
26729C
31516C
35783C
31272C
35784C
See Color Table
See Color Table
See Color Table
70817C
75507C
56082C
70644C
75532C
40045C
70864C
61314C
50986C
70002C
Item No. 5
Part No.
COLOR TABLE
Bronzetone
Gray Beige
Almond
Stainless Stl
Sandalwood
Granite
27502C
23015C
23016C
22822C
23017C
23020C
27432C
23008C
23009C
22814C
23010C
23013C
27591C
23161C
23162C
23137C
23164C
27217C
PANEL
COLOR
Item No. 6
Part No.
Item No. 7
Part No.
11 2
15
3
56
4
12
14
5
16
89
17 9
1
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
DESCRIPTION
All manuals and user guides at all-guides.com

97756C (Rev. G - 9/03)
EIOA4*1E EIOA8*1E EIOATL8*1E EIOA8*3EJO
PAGE 4
ELKAY MANUFACTURING COMPANY  2222 CAMDEN COURT  OAK BROOK, IL
PRINTED IN U.S.A.
PARTS LIST 115V
ITEM NO. PART NO.
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42*
43
44
45
46
47
48
49
50
51
52
53
54
55
56
NS
Item No. 36
Part No.
COLOR TABLE
Bronzetone
Gray Beige
Almond
Stainless Steel
Sandalwood
Granite
27490C
22967C
22968C
22862C
22969C
22972C
27486C
22960C
22961C
22854C
22962C
22965C
27498C
22953C
22954C
22955C
22956C
27214C
Screw-#10 x 1/2"Lg. HHSM
Strainer
Evaporator Assembly
Power Cord
Fan Blade
Hex Nut - Fan Blade
Fan Motor 115V
Screw - Fan Motor
Shroud - Fan
Screw - #8-18 x 3/8" Lg. (Fan Shroud)
Poly Tubing (Cut to Length)
Bubbler Assembly
Bubbler Assembly - Bronzetone
Orifice Assembly
Orifice Assembly - Bronzetone
Guard
Pedestal
Pedestal - Bronzetone
Locknut
Condenser
Drier
Panel -Right Rear
Panel -Left Rear
Panel - Front Lower
Stud - Compressor Mtg.
Grommet - Compressor Mtg.
Clip - Compressor Mtg.
Compressor Serv. Pak EMI 70 HNR
Relay
Cover - Relay
Overload
Heat Exchanger
Drain Tube
Gasket - Drain
Ring Support - Drain
Clamp - Drain Gasket
Hex Nut #10-32
Cold Control
Adaptor - Basin
Basin
Basin - Bronzetone
Cover-Dispenser Bottom
Hanger Bracket
70002C
55996C
66534C
31483C
30664C
70018C
31490C
70009C
22899C
38417001
56092C
51349C
51350C
40322C
40066C
50934C
50168C
50373C
75580C
62152C
66202C
See Color Table
See Color Table
See Color Table
101516143550
100806740570
19037000
36094C
35959C
35768C
36158C
66576C
40614C
50400C
50401C
70444C
70016C
31513C
See Color Table
21903C
27534C
See Color Table
400660943730
PANEL
COLOR
Item No. 37
Part No.
Item No. 53
Part No.
Item No. 56
Part No.
Item No. 38
Part No.
51552C
51551C
51552C
51551C
51552C
51551C
55930C
55931C
55930C
55931C
55930C
55931C
DESCRIPTION
*INCLUDES RELAY & OVERLOAD. IF UNDER WARRANTY, REPLACE WITH
SAME COMPRESSOR USED IN ORIGINALASSEMBLY.
NOTE: All correspondence pertaining to any of the above water coolers or
orders for repair parts MUST include Model No. and Serial No. of cooler,
name and part number of replacement part.
WIRING DIAGRAM
This Drawing is merely for illustrating the
components of the electrical system.
NOTE:
WHEN INSTALLING REPLACEMENT BUBBLER
AND PEDESTAL, TIGHTEN NUT (ITEM 33)
ONLY TO HOLD PARTS SNUG IN POSITION.
DO NOT OVER TIGHTEN.
BASIN
30
31
32
33
29
FIG. 4
CAUTION: Cleaning of Bronzetone Models requires special care. Outer
surfaces must be cleaned with a mild detergent or mixture of vinegar and
water only, rinsed and wiped dry. Abrasive and acidic cleaners may even-
tually damage the Bronzetone finish.
ITEM NO. PART NO.
21
24
42*
43
45
46
-
Power Cord
Fan Motor
Compressor Serv. Pak
Relay
Overload
Heat Exchanger
Power Inlet
35987C
31431C
36092C
36050C
36093C
66561C
35826C
DESCRIPTION
PARTS LIST 220V/60Hz
www.DrinkingFountainDoctor.com 800-518-5388
All manuals and user guides at all-guides.com