Elkay 4430 User manual

PAGE 1 1000004244 (Rev. B - 01/18)
4430_FTN _A LK4430_FTN_A
4430 Fountains are among the easiest to install Fountains on the market today.
To assure you install these models easily and correctly, PLEASE READ THESE
SIMPLE INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL, AND OTHER
APPLICABLE CODES. After installation, leave these instructions with the Fountain for
future reference.
Owners Manual
Model 4430
Tri-Level Tubular Fountain
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO WATER LINES
IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY OCCUR AWAY FROM
THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO A FOUNTAIN, CREATING AN
ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE IN THE METAL CONTENT OF THE
WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER MATERIALS AS INDICATED. ANY DRAIN
FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE OF PLASTIC TO ELECTRICALLY ISOLATE THE
FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
INSTALLER

PAGE 21000004244 (Rev. B - 01/18)
4430_FTN _A LK4430_FTN_A
LEGEND A = 3/8" O.D. UNPLATED COPPER TUBE CONNECT - SHUT OFF VALVE BY OTHERS B = ACCESS PANEL ( 8" X 10" ) C = REMOVABLE BOTTOM COVER
A
1-1/2"
DRAIN
B
BC
C
22 1/4"
565mm
28 9/16" 726mm
29 11/16" 754mm
19" 483mm
19" 483mm
8 3/16" 207mm
2 5/8" 67mm
2 5/8" 67mm
48" 1219mm
27 1/8"
689mm
33 7/16" 850mm
34 9/16" 878mm
41 7/16" 1053mm
2 5/8" 67mm
10" 254mm
O
8" 203mm
30" 762mm
O14"
356mm
O12"
305mm B.C.
O1/2"
13mm (6 PL)

PAGE 3 1000004244 (Rev. B - 01/18)
4430_FTN _A LK4430_FTN_A
1. This fountain is to be mounted on a smooth, at, nished surface with adequate support structure. NOTE: Mounting
structure must be capable of supporting 300 lb. load on fountain.
2. Refer to rough-in for plumbing.
3. Install shut-off valve on water supply. (Valve not furnished)
4. Locate and install fountain using 3/8" minimum fasteners. (Fasteners not furnished).
5. Connect fountain to supply line with a shut-off valve and install a 3/8" unplated copper water line between the valve and the
cooler. Remove any burrs from outside of water line. Push the tubes straight into the ttings until they reach a positive stop,
approximately 3/4" (See Fig. 2). DO NOT SOLDER TUBES INSERTED INTO THE STRAINER AS DAMAGE TO THE
O-RINGS MAY RESULT.
6. Water supply 3/8" O.D. unplated copper tube. Waste 1-1/2" IPS. Contractor to supply waste trap and service stop valve in
accordance with local code.
7. Connect water supply and fountain drain. Connect drain waste "Tee" to fountain drain tubes. Connect outlet of "Tee" to
drainage system. Water connection and drain must comply with local codes.
8. Turn on water supply and check all connections for leaks. Threaded drain ttings may require thread sealer to create a
leak free connection. Apply thread sealer to threaded connection ttings only, not the slip connection ttings.
CAUTION: This fountain is rated for inlet water pressure of 20-105 PSI. A pressure reducing regulator should be used if the
inlet water supply exceeds 105 PSI. Any damage caused by reason of connecting this product to supply line pressures
lower than 20 PSI or higher than 105 PSI is not covered by warranty.
9. Connecting lines to be made of unplated copper and should be thoroughly ushed to remove all foreign matter before being
connected
to fountain. This fountain is manufactured in such a manner that it does not in any way cause taste, odor, color, or sediment
problems.
Actuation of Quick Connect Water Fittings:
Fountain is provided with lead-free connectors which utilize an
o-ring water seal. To remove tubing from the tting, relieve water
pressure, push in on the gray collar while pulling on the
tubing.(see Fig.2) To insert tubing, push tube straight into tting
until it reaches a positive stop, approximately 3/4".
TROUBLE SHOOTING AND MAINTENANCE
STREAM HEIGHT ADJUSTMENT:
Stream height is factory set at 35 PSI. If supply pres-
sure varies greatly from this, insert a small straight
bladed screwdriver through the access hole in the
center of the push button and turn the adjustment
screw. Clockwise adjustment will raise the stream and
counterclockwise adjustment will lower the stream.
For best adjustment, the stream should be approxi-
mately 1 1/2" above the top of the bubbler . (See Fig.
3).
FIG. 3
FIG. 1
1/4” O.D. TUBE
WATER INLET
TO COOLER
3/8” O.D. TUBE CONNECT
COLD WATER SUPPLY
BUILDING WATER
INLET
NOTE: WATERFLOW
DIRECTION
SERVICE STOP
(NOT FURNISHED)
FIG. 2
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C

PAGE 41000004244 (Rev. B - 01/18)
4430_FTN _A LK4430_FTN_A
Vandal-Resistant Bubbler
FIG. 4
BASIN
PRINTED IN U.S.A.
ITEM
NO.
PART NO.
98684C
28467C
0000000325
98530C
97446C
55996C
66346C
40551C
98683C
70852C
97247C
1000003812*
1000003813*
45734C
98682C
1000003694
1000003695
56092C
ITEMIZED PARTS LIST
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
Kit - Drain Elbow/Gasket/Nut/Washer
Basin
Kit - Drain Plug & Gasket
Kit - Regulator/Holder/Nut
Kit - Bubbler (VR)
In - Line Strainer
Drain Tube
Tailpipe
Kit - Drain Adapter/Gasket/Nut/Washer
Tee - 3/8"
Kit - VR Torx Screws/Bit
Access Panel
Bottom Cover
Drain Tube
Kit - Push Button w/Blank Nameplate
Kit - Push Button w/LK4430 Nameplate
Kit - Push Button w/4430 Nameplate
Poly Tubing (Cut To Length)
DESCRIPTION
5
2
3
3
3
11 (4)
12
16 6
10
6
16
16
6
2
3
2
3
5
8
4
11 (4)
5
See Fig. 3
FOR PARTS CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
15
*select color option to complete part number
PRINTED IN U.S.A.
Halsey Taylor – halseytaylor.com
Elkay – elkay.com
*FINISH COLOR OPTIONS – Choose color option to
complete your model number, add as sufx example:
4430EVG
Matte nish: Evergreen = EVG
Gloss nish:
Beige = BGE Gray = GRY Terracotta = TER
Black = BLK Orange = ORN White = WHT
Blue = BLU Purple = PUR Yellow = YLW
Brown = BRN Red = RED
1
1
4
7
4
77
7
5
11 (4)
15
15
15
15
13
9
3
11 (4) 13
12
14
15