Elkay SWIRLFLO Series Installation manual

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
97921C (REV. C - 3/05)
Page 1
SWIRLFLO fountains with FLEXI-GUARD
INSTALLATION, CARE & USE MANUAL
TM TM
!CAUTION
:
Reviewtheseinstructionsbeforebeginninginstallation.Besurethatinstallation
conformsto all plumbing, electrical and other applicable codes.
!
WARNING
:
When installation is complete, ensure these instructions are left in the plastic bag
providedinside the installedunit for futurereference.
!WARNING
:
Serviceto be performedbyauthorized service personnelonly.
INSTALLER
NOTE: It is commonpractice to ground electrical hardware such as telephones, computers and other devices
toavailablewater lines.Thiscan, however,causeelectrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic
taste to it or has a noticeable increase in the metallic content of the water.
Wheninspecting plumbing circuit, remember the line may be groundedsome distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.Any
drain fittings provided by theinstaller should be made of plastic whichwill electronically isolate the
fountainfrom the remainder of the building’splumbingcircuits.
EDFPB114C EDFPBWM114C

97921C (REV. C - 3/05)
EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
Page 2
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
Figure 2 - Rough-in Assembly For EDFPB114C
Figure 1 - Rough-in for EDFPB114C W/MP86 Mounting Plate
Optional

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
97921C (REV. C - 3/05)
Page 3
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
NOTE: Reinforce The Wall In The Shaded Areas
Figure 4 - Rough-in Assembly for EDFPBWM114C
Figure 3 - Rough-in for EDFPBWM114C
Optional

97921C (REV. C - 3/05)
EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
EDFPB114C Installation
1. Wall should already be framed for the fountain using
the positioning dimensions shown in Figure 1. Shown
dimensions pertain to installation location (framing
must support up to 300 lbs. weight). These
dimensions are required for compliance with ANSI
StandardA117.0.
2. Install rough-in plumbing as shown in Figure 1. Run
supply water inlet line through the back panel. Install a
service stop (not provided). Turn on supply water and
flush thoroughly.
3. Install fountain. Remove screw (Item 28) from cover
plate and slide cover plate (Item 14) toward basin.
Mount the fountain to the wall and mounting plate with
(4) 5/16” hex nuts (provided with mounting plate).
Tighten securely. (See Figure 5)
4. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not
provided.
5. Make water supply connections from service stop to
the 3/8” O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks
(See Figure 14). Newly installed water supply line
should be insulated after leak check is completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
6. These products are designed to operate on
20-105 PSIG supply line pressure. If the inlet
pressure is above 105 PSIG, a pressure regulator
must be installed in the supply line. Any damage
caused by reason of connecting these products to
supply line pressures lower than 20 PSIG or higher
than 105 PSIG is not covered by warranty.
7. Check stream height from bubbler. Stream height is
factory set at 35 PSI. If supply pressure varies
greatly from this, remove push button (Item 17 -
Figure 12) and adjust the screw on the regulator
(Item 19 - Figure 12). To remove push button,
remove setscrew from bottom of sleeve (Item 15).
Insert a small punch in screw hole and push
up while grasping the push button and pull forward
removing the push button. Clockwise adjustment
will raise stream height and counterclockwise
movement will lower stream height. For best
adjustment stream should hit basin approximately
6-1/2” from the bubbler. Reassemble push button
by pushing in on button until the push button
catches in the sleeve. Reinstall the setscrew
(Item 31) in the sleeve (Item 15).
Page 4
Figure 5 - EDFPB114C Fountain Installation
Figure 6 - AP-99 Panel (Optional)
28
5/16” Studs - Supplied with MP86
26
14

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
97921C (REV. C - 3/05)
Figure 7 - EDFPBWM114C Panel Installation
Figure 8 - EDFPBWM114C Fountain Installation
EDFPBW114C Installation
1. Wall should already be framed for the fountain using
the positioning dimensions shown in Figure 3. Shown
dimensions pertain to installation location (framing
must support up to 300 lbs. weight). These dimensions
are required for compliance with ANSI Standard A117.0.
2. Install rough-in plumbing as shown in Figure 3. Run
supply water inlet line through the back panel. Install a
service stop (not provided). Turn on supply water and
flush thoroughly.
3. Install back panel. Place the upper edge of the panel
above mounting plate on the wall. Slide the panel down
until it engages the mounting plate. Be sure back panel
is firmly engaged before releasing it. (See Figure 7)
4. Install fountain. Remove screw (Item 28) from cover
plate and slide cover plate (Item 14) toward basin. Mount
the fountain to the back panel and mounting plate with (4)
5/16” x 1” (25mm) long screws (Item 30 - provided).
Tighten securely. (See Figure 8)
5. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not provided.
6. Make water supply connections from service stop to
the 3/8” O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks
(See Figure 14). Newly installed water supply line
should be insulated after leak check is completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
7. These products are designed to operate on 20-105
PSIG supply line pressure. If the inlet pressure is
above 105 PSIG, a pressure regulator must be
installed in the supply line. Any damage caused by
reason of connecting these products to supply line
pressures lower than 20 PSIG or higher than
105 PSIG is not covered by warranty.
8. Check stream height from bubbler. Stream height is
factory set at 35 PSI. If supply pressure varies
greatly from this, remove push button (Item 17 -
Figure 12) and adjust the screw on the regulator
(Item 19 - Figure 12). To remove push button,
remove setscrew from bottom of sleeve (Item 15).
Insert a small punch in screw hole and push up
while grasping the push button and pull forward
removing the push button. Clockwise adjustment
will raise stream height and counterclockwise
movement will lower stream height. For best
adjustment stream should hit basin approximately
6-1/2” from the bubbler. Reassemble push button
by pushing in on the button until the push buttom
catches in the sleeve. Reinstall the setscrew
(Item 31) in the sleeve (Item 15).
Figure 9 - AP-99 Panel (Optional)
30
28
Page 5
25
26
14

97921C (REV. C - 3/05)
EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
Page 6
BUBBLERDETAIL
VANDALRESISTANT
BUBBLERDETAIL
NOTE:
When installing replacement bubbler and pedestal, tighten
nut (Item 7) only to hold parts snug in position. Do Not
Overtighten.
Figure 10 - Bubbler Details
BASIN
5
6
7
2, 3, 4
1
8
9
10
BASIN

EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
97921C (REV. C - 3/05)
Page 7
Figure 11 - Fountain Body
Figure 12 - Push Button
15
16
17 18
19
20
31
32
See Fig. 10 23
11
21
See Fig. 10
12
24
29
13
22
27
14
32
34

97921C (REV. C - 3/05)
EDFPB114C,EDFPBWM114C,EDFPBV114C,EDFPBWMV114C
PARTSLIST
ITEMNO. PARTNO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
56073C
40319C
50171C
50314C
56011C
55997C
75580C
98118C
100322740560
15009C
55001132
55000944
45767C
28343C
45781C
45847C
45848C
50986C
61313C
15005C
56163C
45769C
45768C
56092C
28397C
55000955
111008343890
70432C
38417001
75560C
75632C
70817C
55996C
75671C
Bubbler Assy
Fitting - Orifice
O-Ring
Orifice - Flow Straightener
Housing Assembly
Pedestal
Bubbler Locknut
Body - Bubbler VR
Gasket - Black .68 x 1.03 VR
Nipple - Bubbler VR
Basin - Swirlflow
Lower Shell
Fountain Body
CoverPlate
Sleeve
Pin - Push Button
Push Button
Holder - Regulator
Regulator
RetainingNut
Gasket - Drain
Assy - Drain/Tailpipe
Plug - Drain 1-1/2”
Poly Tubing (Cut To Length)
BackPanel
AP-99 Panel (Optional)
Screw - #10-24 x .62 HHMS
Screw - #8-32 x .38 THSM
Screw - #8-18 x .37 HHSM
Screw - 5/16-18 x 1.00 HHMS
Setscrew - #10-32 x .31
Fttng - Elbow 1/4 x 1/4
Strainer
Spring - Push Button
TROUBLESHOOTING& MAINTENANCE
Orifice Assembly: Mineraldeposits on orifice
can cause water flow to spurt or not regulate. Mineral
depositsmay be removed from the orifice by poking
with a small round file not over 1/8” diameter, or using a
smalldiameter wire.
!
CAUTION
:
DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean, regulate
flow as in Step 7, Page 4 or Step 8, Page 5 of the
installation instructions. If replacement is necessary,
see parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings:
Cooleris provided with lead-free connectorswhich
utilizean o-ring water seal.Toremove tubing from the
fitting,relieve water pressure, push in on the gray
collarwhile pulling on the tubing. (See Figure 13)To
insert tubing, push tube straight into fitting until it
reachesapositivestop (approximately3/4”).
Figure 13 – Quick Connect Fittings
Figure 14 - Water Supply Connections
Page 8
NOTE: WATER FLOW
DIRECTION SERVICE STOP
(NOT FURNISHED)
BUILDING WATER INLE
T
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
1
/4" O.D. TUBE
WATER INLET
TO COOLER
PRINTED IN U.S.A.
33
www.DrinkingFountainDoctor.com 800-518-5388