Elkay Swirlflo EDFPB114FP User manual

Page 1 98008C (Rev. C - 10/17)
EDFPB114FP
SERVICE STOP
(NOT FURNISHED)
BUILDING WATER
INLET
3/8" O.D. UNPLATED COPPER
TUBE CONNECT COLD
WATER SUPPLY
1/4" O.D TUBE
WATER INLET
TO COOLER
NOTE: WATER FLOW
DIRECTION
Installation Manual
EDFPB114FPC
Swirlo®Freeze Resistant Fountain
IMPORTANT! INSTALLER PLEASE NOTE.
THE GROUNDING OF ELECTRICAL EQUIPMENT SUCH AS TELEPHONE, COMPUTERS, ETC. TO
WATER LINES IS A COMMON PROCEDURE. THIS GROUNDING MAY BE IN THE BUILDING OR MAY
OCCUR AWAY FROM THE BUILDING. THIS GROUNDING CAN CAUSE ELECTRICAL FEEDBACK INTO
A FOUNTAIN, CREATING AN ELECTROLYSIS WHICH CAUSES A METALLIC TASTE OR AN INCREASE
IN THE METAL CONTENT OF THE WATER. THIS CONDITION IS AVOIDABLE BY USING THE PROPER
MATERIALS AS INDICATED. ANY DRAIN FITTINGS PROVIDED BY THE INSTALLER SHOULD BE MADE
OF PLASTIC TO ELECTRICALLY ISOLATE THE FOUNTAIN FROM THE BUILDING PLUMBING SYSTEM.
IMPORTANT
ALL SERVICE TO BE PERFORMED BY AN AUTHORIZED SERVICE PERSON
FIG. 1
TUBE IS
SECURED
IN POSITION
SIMPLY PUSH IN
TUBE TO ATTACH
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
FIG. 2
OPERATION OF QUICK CONNECT FITTINGS
To assure you install this model easily and correctly, PLEASE READ THESE SIMPLE
INSTRUCTIONS BEFORE STARTING THE INSTALLATION. CHECK YOUR
INSTALLATION FOR COMPLIANCE WITH PLUMBING, ELECTRICAL AND OTHER
APPLICABLE CODES. After installation, leave these instructions with the building owner
for future reference. This Freeze Resistant Fountain is shipped in two separate cartons.
The second carton contains the Freeze Resistant Package LKFRB1 that is installed on an
interior heated wall. Refer to the Freeze Resistant Package for the rough-in dimensions
for installation.
INSTALLER

Page 2
EDFPB114FP
98008C (Rev. C - 10/17)
16" 406mm
33 15/16"
863mm
1 5/8"
41mm
5" 127mm
6" 152mm 25 3/8"
645mm
1/2"
13mm
28 3/4" 730mm
30 1/4"
768mm
8" 203mm
1/2"
13mm
FINISHED FLOOR
B
A
18 3/8" 467mm
3/8" (10mm) DIA HOLES (4) FOR SECURING MOUNTING
PLATE TO STUDS
27" 686mm
ADA
REQUIREMENT
13 3/8" 339mm
2 5/8"
66mm
3 5/8"
91mm
12" 305mm
MAX. WALL
THICKNESS 14 3/8"
364mm
17 7/8"
453mm
28 15/16"
735mm
C
1/2"
13mm
FIG. 3
EDFPB114FPC ROUGH-IN
LEGEND: A = 7/8" (22mm) DIA. HOLE FOR WATER SUPPLY TUBE B = 1-3/4" (44mm) DIA. HOLE FOR WASTE LINE C = 7/8" (22mm) DIA. HOLE FOR OPERATING CABLE *Note: All dimensions are taken from the nished oor on the side of the wall that the fountain is installed on.
7 1/4"
184mm
12 1/8" 307mm
12" 305mm MAX. WALL
THICKNESS

Page 3 98008C (Rev. C - 10/17)
EDFPB114FP
FIG. 4
CABLE SHEATH ADJUSTMENT
To Increase Free Play
To Reduce Free Play
12, 13
4
7
INSTALLATION INSTRUCTIONS
1. Wall should already be framed for the fountain using the positioning dimensions shown in Fig. 3. Shown dimensions pertain
to installation location (framing must support up to 300 lbs. weight). These dimensions are required for compliance with
ANSI Standard A117.1/ADA requirements.
2. The freeze resistant package must be mounted on an interior wall in a heated area. The room temperature of the interior heated
area must be 50° F (10° C) or higher. The freeze resistant package may be surface or recessed mounted. If recess mounted the
 surfaceofthecovermustbeushwiththeinteriorwallsurface.Thepackageisfurnishedwithscrewsformountingthecoverto
the box. If the box is recess mounted, do not fasten the top and bottom of the cover to the box. Use the holes on the front only.
3. To assemble the operating cable to the sleeve inside the fountain arm you will need to remove cap screw (Item 2, See Fig. 6)
and then remove Push Button and Pin (Items 12 & 13, See Fig. 4). Remove screw (Item 4, See Fig. 4) and you will now be
able to remove the Sleeve (Item 7, See Fig. 4) to get access to the adjustment nuts for additional adjustability. (Fountain should
be mounted to exterior wall). The adjustment nuts should be at the base of the threaded area on the operating cable. See Fig. 4.
Create a loop in the cable and thread the free end of the cable through the wall into the freeze resistant box.
4. Connect free end of operating cable to the valve-operating bracket in the freeze resistant box.
5. Remove cable free play by adjusting the jam nuts on the ends of the operating cable. See Fig. 4.
6.Connectwaterlinefromfountainbubblerintofreezeresistantbox.Theconnectiontotheboxusesaquickconnectwatertting.
Position the water line, in the fountain, to drain back into interior mounted box. Any water left standing, in the exterior line, can
freeze. To insure positive draining of the bubbler supply tube, excess length should be trimmed off and discarded.
7. Connect drain and water supply lines to the freeze resistant fountain. Inline strainer must be used on the inlet water line. See
Figure 1.
START UP
1. Turn on building water supply and check all connections for leaks. Repair as required.
2. Stream height is factory set at 35 PSI. If stream height needs to be changed adjust the regulator in the freeze resistant package.
Clockwise adjustment raises stream height, counter clockwise adjustment will lower stream.
3. Adjust operating cable as required. Cable system should have a minimal amount of free play to allow for proper valve operation.
 Ifthesystemistootightthevalvewillstayintheonpositioncreatingconstantwaterow.Toomuchfreeplaywillresultinnon-
operation of the valve with the push-buttons.
4. Note: Water from the drain back tube in the freeze resistant package will continue to run while the valve is actuated.
5.Aftercablesystemisadjustedproperly,stuffexibleinsulationintoanyopeningsbetweentheoutsidewallandtheinteriorbox.
6. Recheck all connections. If all connections are leak free replace cover(s) on the freeze resistant box(es) and fountain(s).

Page 4
EDFPB114FP
98008C (Rev. C - 10/17)
FIG. 6
NOTE:
When installing replacement bubbler and
pedestal, tighten locknut only to hold parts
snug in position. Do Not Overtighten.
SEE FIG. 5
FIG. 5
PARTS LIST
ITEM NO. PART NO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
NS
NS
56073C
75669C
56092C
111008343890
70817C
15027C
15025C
28708C
28473C
45767C
28343C
45848C
45821C
56163C
0000000930
45768C
70432C
75560C
Bubbler Assy
Cap Screw - #6-32 x 1.25"
Poly Tubing (Cut To Length)
Screw - #10-24 x .62 HHSM
Fttng - Elbow 1/4 x 1/4
Brkt-Swirlow
Assy-Sleeve/ButtonSwirlo
Basin-Swirlow(Polished)
Lower Shell
Fountain Body
Cover Plate
Button-PushSwirlo
Pin-PushButtonSwirloFP
Gasket - Drain
Assy - Drain/Tailpipe
Drain - Plug 1-1/2
Screw - #8-32 x .38 THTC
Screw - 5/16-18 x 1.00 HHMS
3, 5 15
11
9
5
14
8
16
10
13 2
12
4
7
6
4
LOCKNUT
BASIN
1
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484 • www.elkay.com
PRINTED IN U.S.A.
NS = NOT SHOWN
1