Elkay SWIRLFLO Series Installation manual

Page 1
EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC,EBFPBMV117RAC
97922C (Rev. E - 3/05)
SWIRLFLO fountains with FLEXI-GUARD
INSTALLATION, CARE & USE MANUAL
TM TM
!
CAUTION
:
Reviewtheseinstructionsbeforebeginninginstallation.Be sure that installation
conformstoallplumbing,electricalandotherapplicablecodes.
!WARNING
:
When installation is complete, ensure these instructions are left in the plastic bag
providedinside theinstalled unit forfuture reference.
!WARNING
:
Serviceto beperformed by authorizedservice personnel only.
INSTALLER
NOTE: It is commonpracticetogroundelectrical hardware such as telephones, computers and other devices
toavailable water lines.This can, however, cause electrical feedbackinthe plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a metallic
taste to it or has a noticeable increase in the metallic content of the water.
Wheninspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.Any
drain fittings provided by theinstaller should be made of plastic whichwillelectronically isolate the
fountainfrom the remainder ofthe building’s plumbing circuits.
EDFPBM(V)117C EDFPBM(V)117RAC

EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
Page 2
97922C (Rev. E - 3/05)
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
Note: Reinforce The Wall In The Shaded Areas.
Figure 2 - Rough-in Assembly EDFPBM(V)117C
Figure 1 - Rough-in EDFPBM(V)117C
Optional

Page 3
EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
97922C (Rev. E - 3/05)
LEGEND
A = Water Inlet Location Left Or Right Side. 3/8” O.D. Unplated Copper Tube Connect.
B = Fountain Waste Location Left Or Right Side. Waste Is Shown in Wall But May Be Behind
Wall. 1-1/4” O.D. Drain (Trap Not Furnished)
C = Opening For Optional AP-99 Access Panel
Note: Reinforce The Wall In The Shaded Areas.
Figure 3 -Rough-in EDFPBM(V)117RAC
Figure 4 -Rough-in Assembly EDFPBM(V)117RAC
Optional

EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
Page 4
97922C (Rev. E - 3/05)
Figure 5 -Panel Installation
Figure 6 - Fountain Installation
Figure 7 - AP-99 Panel (Optional)
30
28
Installation Instructions:
1. Wall should already be framed for the fountain using
the positioning dimensions shown in Figure 1 or
Figure 3. Shown dimensions pertain to installation
location (framing must support up to 300 lbs. weight).
These dimensions are required for compliance with
ANSI StandardA117.0.
2. Install rough-in plumbing as shown in Figure 1 or
Figure 3. Run supply water inlet line through the back
panel. Install a service stop (not provided). Turn on
supply water and flush thoroughly.
3. Install back panel. Place the upper edge of the panel
above mounting plate on the wall. Slide the panel down
until it engages the mounting plate. Be sure back panel
is firmly engaged before releasing it. (See Figure 5)
4. Install fountain. Remove screw (Item 28) from cover
plate and slide cover plate (Item 14) toward basin.
Mount the fountain to the back panel and mounting
plate with (4) 5/16” x 1” (25mm) long screws
(Item 30 - provided). Tighten securely. (See Figure 6)
5. Determine required length of waste line and cut to
appropriate length. 1-1/4” O.D. waste tube furnished.
1-1/4” slip trap, waste elbow and extension not provided.
6. Make water supply connections from service stop to
the 3/8” O.D. unplated copper tube coming out of the
strainer. Turn on water supply and check for leaks (See
Figure 12). Newly installed water supply line should be
insulated after leak check is completed.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to the
o-rings may result.
7. These products are designed to operate on 20-105
PSIG supply line pressure. If the inlet pressure is
above 105 PSIG, a pressure regulator must be
installed in the supply line. Any damage caused by
reason of connecting these products to supply line
pressures lower than 20 PSIG or higher than
105 PSIG is not covered by warranty.
8. Check stream height from bubbler. Stream height is
factory set at 35 PSI. If supply pressure varies greatly
from this, remove push button (Item 17 - Figure 10)
and adjust the screw on the regulator
(Item 19 - Figure 10). To remove push button, remove
setscrew from bottom of sleeve (Item 15). Insert a small
punch in screw hole and push up while grasping the
push button and pull forward removing the push button.
Clockwise adjustment will raise stream height and
counterclockwise movement will lower stream height.
For best adjustment stream should hit basin
approximately 6-1/2” from the bubbler. Reassemble
the push button by pushing in on button until the push
button catches in the sleeve. Reinstall the setscrew
(Item 31) in the sleeve (Item 15).
25
26
14

Page 5
EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
97922C (Rev. E - 3/05)
BUBBLERDETAIL
VANDALRESISTANT
BUBBLERDETAIL
NOTE:
When installing replacement bubbler and pedestal, tighten
nut (Item 7) only to hold parts snug in position. Do Not
Overtighten.
Figure 8 - Bubbler Details
BASIN
5
6
7
2, 3, 4
1
8
9
10
BASIN

EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
Page 6
97922C (Rev. E - 3/05)
Figure 9 - Fountain Body
Figure 10 - Push Button
15
16
17 18
19
20
31
32
11
21
See Fig. 8
12
24
29
13
22
27
14
23
See Fig. 8
32
34

Page 7
EDFPB117C,EDFPBM117C,EDFPB117RAC,EDFPBM117RAC,EDFPBV117C,
EDFPBMV117C,EDFPBV117RAC, EBFPBMV117RAC
97922C (Rev. E - 3/05)
Figure 12 – Water Supply Connections
NOTE: WATER FLOW
DIRECTION SERVICE STOP
(NOT FURNISHED)
BUILDING WATER INLE
T
3/8" O.D. UNPLATED
COPPER TUBE CONNECT
COLD WATER SUPPLY
1
/4" O.D. TUBE
WATER INLET
TO COOLER
TROUBLESHOOTING& MAINTENANCE
OrificeAssembly: Mineral depositson
orificecan cause water flow to spurt ornot
regulate.Mineraldeposits may beremoved
fromtheorifice by pokingwith a smallround
filenot over 1/8”diameter,or using asmall
diameterwire.
!CAUTION
:
DO NOT file or cut orifice
material.
Stream Regulator: If orifice is clean,
regulateflowas in Step 8 of theinstallation
instructions.Ifreplacementisnecessary,see
parts listforcorrect regulator partnumber.
Actuation of Quick Connect Water
Fittings: Cooler is provided with lead-free
connectorswhichutilizeano-ringwaterseal.
Toremovetubing from the fitting, relievewater
pressure,pushinonthegraycollar while
pullingonthe tubing. (SeeFigure11)Toinsert
tubing,pushtubestraight intofittinguntilit
reachesapositivestop(approximately3/4”).
Figure 11 – Quick Connect Fittings
PARTSLIST
ITEMNO. PARTNO. DESCRIPTION
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
56073C
40319C
50171C
50314C
56011C
55997C
75580C
98118C
100322740560
15009C
28474C
28473C
45767C
28343C
45781C
45847C
45848C
50986C
61313C
15005C
56163C
45769C
45768C
56092C
28392C
28393C
55000966
111008343890
70432C
38417001
75560C
75632C
70817C
55996C
75671C
Bubbler Assy
Fitting - Orifice
O-Ring
Orifice - Flow Straightener
Housing Assembly
Pedestal
Bubbler Locknut
Bubbler Assembly VR
Gasket - Black .68 x 1.03 VR
Nipple - Bubbler VR
Basin - Swirlflow
Lower Shell
Fountain Body
CoverPlate
Sleeve
Pin - Push Button
Push Button
Holder - Regulator
Regulator
RetainingNut
Gasket - Drain
Assy - Drain/Tailpipe
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Back Panel RHADA
Back Panel LHADA
AP-99 Panel (Optional)
Screw - #10-24 x .62 HHMS
Screw - #8-32 x .38 THSM
Screw - #8-18 x .37 HHSM
Screw - 5/16-18 x 1.00 HHMS
Setscrew - #10-32 x .31
Fttng - Elbow 1/4 x 1/4
Strainer
Spring - Push Button
PRINTED IN U.S.A.
33
www.DrinkingFountainDoctor.com 800-518-5388