Elkay SWIRLFLO ERPB2-8C Installation manual

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
97924C (Rev. J - 07/16)
Page 1
ERPB2-8C ERPB2-8RAC
SWIRLFLO®Refrigerated fountains with FLEXI-GUARD®
INSTALLATION, CARE & USE MANUAL
Review these instructions before beginning installation. Be sure that installation
conforms to all plumbing, electrical and other applicable codes.
When installation is complete, ensure these instructions are left in the plastic bag
provided inside the installed unit for future reference.
Service to be performed by authorized service personnel only.
INSTALLER
NOTE: It is common practice to ground electrical hardware such as telephones, computers and other devices
to available water lines. This can, however, cause electrical feedback in the plumbing circuit, which
results in an “electrolysis” effect occurring in the fountain. This may result in water which has a
metallic taste to it or has a noticeable increase in the metallic content of the water.
When inspecting plumbing circuit, remember the line may be grounded some distance from the
installation, and may occur outside the building or area in which the unit is being installed.
This condition can be avoided (in most cases) by using recommended materials during installation.
Any drain ttings provided by the installer should be made of plastic which will electronically isolate
the fountain from the remainder of the building’s plumbing circuits.

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
Page 2
97924C (Rev. J - 07/16)
LEGEND A = 1/4” O.D. Tube - Water Outlet Connection B = 3/8” O.D. Tube - Water Inlet Connection C = 1-1/4” Waste Tube D = ELECTRICAL INLET
Figure 1 - Rough-in Dimensions
Model LRPB2-8C Model LRPB2-8RAC

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
97924C (Rev. J - 07/16)
Page 3
Figure 4 - LRPB Tube Routing
1. Install chiller: Remove front panel of chiller. Remove
and discard cardboard inner pack from between
compressor and side panel. Slide chiller onto the
shelf and position it to the left as per dimensions in
Figure 1.
Note: Building construction must allow for
adequate air ow on both sides, top and
back of chiller. A minimum of 4” (102mm) on
both sides and top is required. See chiller
installation for additional instructions.
2. Make water supply connections. Install a shut-off valve
and union connection to building water supply (valve and
union not provided). Turn on water supply and ush the
line thoroughly.
3. ERPB Models: Make connection between remote chiller
and building supply line. Inlet port is marked on the chiller
(1/4” O.D. copper tube). Bend the copper tube (provided)
at an appropriate length from chiller to opening in frame.
Install the in-line strainer (provided with chiller) by pushing
it until it reaches a positive stop, approximately 3/4” (19mm)
on the marked chiller inlet port. Connect building supply
line to strainer. (See Figure 3)
Caution: DO NOT SOLDER tubes inserted
into the strainer as damage to
o-rings may result.
4. LRPB Models: Mount lter head assembly to side of
chiller (See Figure 4). Make connections between lter
and building supply line (3/8” O.D. tube not provided).
Inlet port is marked on the chiller (1/4” O. D. copper tube).
Install a 1/4” x 1/4” union (provided) on the marked chiller
inlet port. Insert the 1/4” poly tubing (provided) into the
tting on lter and connect the union to the chiller.
(See Figure 4)
Caution: DO NOT SOLDER tubes inserted
into the strainer as damage to
o-rings may result.
Special Tools
Item Description Quantity
NONE
Additional Materials
Item Description Quantity
1 Unplated copper inlet pipe
2 Service Stop
REQUIRED TOOLS AND MATERIALS
These tables show special tools and/or
additional materials (not provided) which are
necessary to complete installation of these
units:
Figure 2 - Chiller Installation
CHILLER
INLET
CHILLER
OUTLET
27
26
19
TO BUBBLER
26
Figure 3 - ERPB Tube Routing
TO BUBBLER
26
27 18 26
26
CHILLER
OUTLET
WATER
INLET
Note: Danger! Electric shock hazard. Disconnect power before servicing unit.
Uses HFC-134A refrigerant

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
Page 4
97924C (Rev. J - 07/16)
Figure 5 - Upper Panel Installation
Figure 6 - Fountain Installation
Figure 7 - Lower Panel Installation
5. Hang the upper panel on the mounting frame hanger. Be
sure that the panel is engaged with hanger at the top of
frame before releasing it. Align holes in the panel with holes
in the mounting frame. Install two (2) #10-24 x 5/8” (16mm)
screws (Item 11 - Figure 5) in holes and tighten securely.
6. Install the fountain. Remove the screw (Item 12) from cover
plate and slide cover plate (Item 16) toward basin. Mount the
fountain to the upper panel and frame with (4) 5/16” x 1”
(25mm) bolts (Item 27), brackets (Item 9) and nuts
(Item 8) provided. Tighten securely. Brackets (Item 9)
must be installed as shown to properly support
fountains. (See Figure 6)
7. Attach waste tube (1-1/4” O.D.) to 1-1/4” O.D. slip
trap (provided by others).
8. ERPB Models: Make connections between remote chiller
outlet tube and fountain. Outlet port is marked on the chiller
(1/4” O.D. copper tube). Install a 1/4” x 1/4” tee (provided)
on the marked chiller outlet port. Insert the 1/4” poly tubing
coming from the fountain into the union. Turn on the water
supply and check for leaks.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to
o-rings may result.
LRPB Models: Make connections between remote chiller
outlet tube and fountain. Outlet port is marked on the
chiller (1/4” O.D. copper tube). Install a 1/4” x 1/4” tee
(provided) on the marked chiller outlet port. Insert the 1/4”
poly tubing coming from the fountain into the union.
CAUTION: DO NOT SOLDER tubes inserted
into the strainer as damage to
o-rings may result.
9. These products are designed to operate on 20-105
PSI supply line pressure. If inlet pressure is above
105 PSI, a pressure regulator must be installed in
the supply line.
CAUTION: Any damage caused by connecting
these products to a supply line with
pressure lower than 20 PSI or
higher than 105 PSI IS NOT
covered under warranty.
10. Make electrical connections to the chiller. See
chiller instructions.
11. Check stream height from bubbler. Stream height is
factory set at 35 PSI. If supply pressure varies greatly from
this, remove push button (Item 3 - Figure 11) and adjust
the screw on the regulator (Item 4 - Figure 11). To remove
push button, remove set screw from bottom of sleeve
(Item 6). Insert a small punch in screw hole and push up
while grasping the push button and pull forward removing
the push button. Clockwise adjustment will raise stream height
and counterclockwise movement will lower stream height. For
best adjustment stream should hit basin approximately 6-1/2”
from the bubbler. Reassemble push button by pushing in on
button until the push button catches in the sleeve. Reinstall
the setscrew (Item 6) in the sleeve (Item 17).
12. Mount lower panel. Loosen the three (3) #10-24 x 5/8”
(16mm) screws (Item 11 - Figure 6) at frame bottom lip. Slide
upper tongue of lower panel under lower edge of already
installed upper panel. Tighten previously loosened screws
securely. (See Figure 7)
30
12
11
20, 21, 22, 23
11
24
9
8
View From Rear
16

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
97924C (Rev. J - 07/16)
Page 5
FLEXI-GUARD®BUBBLER DETAIL or
FLEXI-GUARD®STREAMSAVER™ BUBBLER DETAIL
VANDAL RESISTANT BUBBLER DETAIL or
VANDAL RESISTANT STREAMSAVER BUBBLER DETAIL
NOTE:
When installing replacement bubbler and pedestal, tighten
locknut only to hold parts snug in position. Do Not Overtighten.
Basin
Figure 8 - Bubbler Details
1 or 2
Locknut
10A or 10B
Basin
DESCRIPTION
1
2
3
ITEM NO. PART NO.
51299C
98926C
51469C
Filter Assy - 1500 Gallon
Kit-Filter Head Fitting Includes John Guest
Fittings
Assy-Filter Head & Mounting Bracket/John
Guest Ftgs/Screws
WATERSENTRY® FILTER PARTS LIST
(See Fig. 9)
(When provided)
2
1
Figure 9 - Filter Assembly
WaterSentry®Filter Detail
3
2

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
Page 6
97924C (Rev. J - 07/16)
Figure 10 - Fountain Body Assembly
Figure 11 - Push Button Assembly
17
3
34
4
4
6
7
25
See Fig. 8
13
28
See Fig. 8
14
26
5
15
29
11
16
7
3

ERPB2-8C, ERPB2-8RAC, ERPBV2-8C, ERPBV2-8RAC, LRPB2-8C, LRPB2-8RAC, ERPB2-8C*2C, ERPB2-8C*3C
ERPB2-8GRNC*A, ERPB2-8GRNRAC*A, LRPB2-8GRNC*A, LRPB2-8GRNRAC*A
97924C (Rev. J - 07/16)
Page 7
B CA
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
OPERATION OF QUICK CONNECT FITTINGS
SIMPLY PUSH IN
TUBE TO ATTACH
TUBE IS SECURED
IN POSITION
PUSH IN COLLET
TO RELEASE TUBE
PUSHING TUBE IN BEFORE
PULLING IT OUT HELPS TO
RELEASE TUBE
A B C
1
2
3
4
5
6
7
8
9
10A
10B
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
56073C
98501C
98871C
98530C
38417001
75632C
70817C
70020C
28395C
97446C
98481C
111008343890
70432C
28708C
28473C
45767C
28343C
45781C
1000002162
55996C
28383C
28384C
1000003513
1000003514
27026C
45768C
56092C
1000001994
56163C
45769C
75560C
Bubbler Assy
Bubbler Assy (Stream Saver)
Kit - Push Button/Spring/Washer
Kit - Regulator/Holder/Nut
Screw - #8-18 x .37 HHSM
Setscrew - #10-32 x .38
Fttng - Elbow 1/4 x 1/4
Nut - Hex 5/16-18
Bracket - Support
Bubbler Assembly VR
Bubbler Assy. VR StreamSaver
Screw - #10-24 x .62 HHSM
Screw - #8-32 x .38 THSM
Basin - Swirlow
Lower Shell
Fountain Body
Cover Plate
Sleeve
Kit - Union 1/4” x 1/4” (3 Pack)
Strainer (Provided with Chiller)
Back Panel RH ADA
Back Panel LH ADA
Back Panel RH ADA (Green Spec)
Back Panel LH ADA (Green Spec)
Lower Panel
Drain - Plug 1-1/2”
Poly Tubing (Cut To Length)
Kit - Tee - 1/4” (3 Pack)
Gasket - Drain
Assy - Drain/Tailpipe
Screw - 5/16-18 x 1.00 HHMS
PARTS LIST
ITEM NO. PART NO. DESCRIPTION
Installation Package
The components for installation are packed in three
separate boxes, regardless of the type of unit being
installed. The boxes contain the following:
Box No. 1: Wall Frame(s)
Box No. 2: Remote Chiller, ECH8
Box No. 3: Fountain Arm and Panels
Additional materials, as noted in the Parts List, are also
shipped in these boxes.
TROUBLESHOOTING & MAINTENANCE
Orice Assembly: Mineral deposits on
orice can cause water ow to spurt or not
regulate. Mineral deposits may be removed
from the orice by poking with a small round
le not over 1/8” diameter, or using a small
diameter wire.
DO NOT le or cut orice
material.
Stream Regulator: If orice is clean,
regulate ow as in Step 11 of the installation
instructions. If replacement is necessary, see
parts list for correct regulator part number.
Actuation of Quick Connect Water Fittings:
Cooler is provided with lead-free connectors
which utilize an o-ring water seal. To remove
tubing from the tting, relieve water
pressure, push in on the gray collar while
pulling on the tubing. (See Figure 13) To
insert tubing, push tube straight into tting
until it reaches a positive stop approximately
3/4”).
Figure 13 – Quick Connect Fittings
Figure 12 – Water Supply Connections
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.834.4816
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640