Elkay VRCTLFR Series Installation manual

98220C (2/06)
VRCTLFR8*1A
10
Page 1
Uses HFC-134A refrigerant
VRCTLFR Series Barrier-Free Water Coolers
TM
NOTE: Non-refrigerated units do not include all electrical and refrigeration components
shown above. Other components and rough-in are the same as shown.
INSTALLATION, CARE & USE MANUAL
20 6
38, 39
56
42
1, 4
16
7, 22, 41
See Fig. 3
See Fig. 6
25
25
45
54
21
43
19
11
32
37
45
45 9, 12, 13
21 49
33
45 37
16
8
32
33
21
45
23, 30
42
16 16 23, 30
2, 3, 5
1, 4
51
53
55 50
57
58
58
59

98220C (2/06)
VRCTLFR8*1A
LEGEND/LEYENDA/LÉGENDE A = RECOMMENDED WATER SUPPLY LOCATION 3/8 O.D. UNPLATED COPPER TUBE CONNECT STUB WITH SHUT OFF (BY OTHERS) 3 IN. (76mm) MAXIMUM OUT FROM WALL B = RECOMMENDED LOCATION FOR WASTE OUTLET 1-1/2” O.D. DRAIN STUB 2 IN. OUT FROM WALL C = 1-1/2 TRAP NOT FURNISHED D = ELECTRICAL SUPPLY (3) WIRE RECESSED BOX E = INSURE PROPER VENTILATION BY MAINTAINING 6" (152 mm) (MIN.) CLEARANCE FROM CABINET LOUVERS TO WALL. F = 7/16 BOLT HOLES FOR FASTENING UNIT TO WALL
FIG. 2
Page 2
REDUCE HEIGHT BY 3” FOR INSTALLATION OF CHILDRENS ADA COOLER
*
ADAREQUIREMENT

98220C (2/06)
VRCTLFR8*1A
Page 3
Stainless Steel
PANEL COLOR
COLOR TABLE Item No. 37
Part No.
Item No. 32
Part No. Item No. 33 Part No. Item No. 34 Part No. Item No. 35 Part No. Item No. 36 Part No.
28525C 28519C 28516C 28536C 28522C 22955C
Refrig. Unit
Stainless Steel
PANEL COLOR
COLOR TABLE Item No. 37
Part No.
Item No. 32
Part No. Item No. 33 Part No. Item No. 34 Part No. Item No. 35 Part No. Item No. 36 Part No.
28539C 28519C 28516C 28528C 28522C 22955C
Left Unit
IMPORTANT
ALL SERVICE TO BE PERFORMED BY
AN AUTHORIZED SERVICE PERSON
HANGER BRACKETS & TRAP
INSTALLATION
1) Remove hanger bracket fastened to back of cooler by removing one (1)
screw.
2) Mount the hanger bracket and trap as shown in Figure 2.
NOTE: Hanger Bracket MUST be supported securely. Add fixture support
carrier if wall will not provide adequate support.
IMPORTANT:
y6 1/4 in. (159mm) dimension from wall to centerline of trap must be
maintained for proper fit.
yAnchor hanger securely to wall using all five (5) 1/4 in. dia. mounting
holes.
3) Install straight valve for 3/8" O.D. tube.
INSTALLATION OF COOLER
4) Hang the cooler on the hanger bracket. Be certain the hanger bracket is
engaged properly in the slots on the cooler back as shown in Figure 2.
5) Loosen the two (2) screws holding the lower front panel at the bottom of
cooler base and two (2) screws at the top (Use torx bits sold separately).
Remove the front panel and set aside.
6) Connect water inlet line--See Note 4 of General Instructions.
7) Remove the slip nut and gasket from the trap and install them on the cooler
waste line making sure that the end of the waste line fits into the trap.
Assemble the slip nut and gasket to the trap and tighten securely. Recom-
mend fastening cooler to wall using 7/16 bolt holes. (see fig.2, "F")
START UP
Also See General Instructions
8) Stream height is factory set at 45-50 PSI. If supply pressure varies
greatly from this, adjust screw using the access hole in the pushbutton
(insert screwdriver). CW adjustment will raise stream and CCW adjust-
ment will lower stream. For best adjustment, stream should hit basin
approximately 6-1/2” (165mm) from bubbler.
Fig. 3
VANDAL RESISTANT BUBBLER DETAIL
15
1
4
Basin

98220C (2/06)
VRCTLFR8*1A
Page 4
Fig. 4
(Refrigerated side shown)
30
1
45 (8)
23
15
25
4
50 (RH Unit)
55 (LH Unit)
33
31
24
32
46
45 (6)
35
36
28
48
44
40
17, 18, 14
26
47 (4)
34
52
27
46
46
29
(Items 31 & 24 also
used on the LH unit)

98220C (2/06)
VRCTLFR8*1A
Page 5
Fig. 5
Thermostat Installation Detail
Fig. 6
Heater Strip Detail
WARNING!
This unit is frost resistant down to 0° F with no wind.
Prevailing winds can reduce the ability of the heater
element to prevent light freezing. If the ambient air
temperature will drop below 0° F, the cooler needs to
be drained of all water by blowing out all water lines,
evaporator (item 20), and the drain trap. A heater
strip is used to heat the unit and will begin to cycle
at 40° +/- 5° F. A check at this temperature will
ensure the heater is working and the unit is resis-
tant to light freezing.
ALSO, MAKE SURE THERE ARE NO PLASTIC OR
FLAMMABLE COMPONENTS DIRECTLY ABOVE
THE HEATER STRIP. Wiring Diagram
59
21
21
60
57
58
61
45
61

98220C (2/06)
VRCTLFR8*1A
100322740560
100806740570
101516143550
15009C
19037000
30664C
31490C
31513C
35768C
35870C
36094C
36158C
35959C
50986C
45866C
56092C
15005C
61313C
66703C
66534C
70002C
70009C
45768C
28617C
28593C
22897C
45662C
45737C
75672C
56163C
28596C
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
See Color Table
66743C
56237C
40045C
70018C
75524C
55996C
45736C
75570C
75661C
70864C
56033C
66576C
45865C
27124C
55931C
40022C
75583C
45864C
70682C
35906C
35907C
35909C
70432C
75506C
75520C
75523C
28551C
Gasket - Bubbler
Grommet - Compressor Mtg.
Stud - Compressor Mtg.
Nipple - Bubbler
Clip - Compressor Mtg.
Fan Blade
Fan Motor
Cold Control
Cover - Relay
Power Cord
Compressor Serv. Pak EMI 70
Overload
Relay
Holder - Regulator
Bubbler Assy.
Tubing - Poly (Cut To length)
Retaining Nut
Regulator
Drier
Evaporator Assembly
Screw - #10 x 1/2” Lg. HHSM
Screw - Fan Motor
Drain Plug 1-1/2
Screen - VR
Basin - Stainless Steel
Panel - Bottom Dispenser
Button - Push
Sleeve - Push Button
Cap Screw
Gasket - Drain
Panel - Screen
Panel - RH Rear
Panel - LH Rear
Panel - RH Dispenser Side
Panel - LH Dispenser Side
Panel - Dispenser Front
Panel - Front Lower
Condenser
Shroud Fan
Hex Nut
Hex Nut - Fan Blade
Clip (Front & Rear Panels)
Strainer (See “General Instructions”)
Half Nut - Regulator
Screw - #10 x .50 Pinned Torx
Screw - #8 x .50 Pinned Torx
Screw - #8 x .62 Torx/Slot
Washer
Heat Exchanger
Assy. Drain/Tailpipe (RH unit)
Cover - Cold Control
Cover - Dispenser Bottom
Drain Tube Assy.
Elbow
Assy. Drain/Tailpipe (LH unit)
Tee 1/4
Heater Strip
Switch - Rocker
FR Thermostat Assy.
Screw - 8-32 x .38 THTC
Screw - #10 x .75 HHSM
Torx Tool - T25
Torx Tool - T20
Hanger Bracket
PART NO. DESCRIPTION
*REPLACE WITH SAME COMPRESSOR USED
IN ORIGINAL ASSEMBLY.
NOTE: All correspondence pertaining to any of the
above water coolers or orders for repair parts MUST
include Model No. and Serial No. of cooler, name and
part number of replacement part.
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
Sold Separate
Sold Separate
NS
ITEM NO.
115V PARTS LIST
*
PRINTED IN U.S.A.
FOR PARTS, CONTACT YOUR LOCAL DISTRIBUTOR OR CALL 1.800.323.0620
ELKAY MANUFACTURING COMPANY • 2222 CAMDEN COURT • OAK BROOK, IL 60523 • 630.574.8484
Page 6
REPAIR SERVICE INFORMATION TOLL FREE NUMBER 1.800.260.6640