Elmo L-12G User manual

INSTRUCTION MANUAL
VISUALPRESENTER
L-12G / TT-12G
Please read this instruction manual carefully before using
this product and keep it for future reference.

2
■ Read Instructions
All the safety and operating instructions should be read before the appliance is operated.
■ Retain Instructions
The safety and operating instructions should be retained for future reference.
■ Heed Warnings
All warnings on the product and in the operating instructions should be adhered to.
■ Follow Instructions
All operating and use instructions should be followed.
■ Cleaning
Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use
a damp cloth for cleaning.
■ Attachments
Do not use attachments not recommended by the product manufacturer as they may cause hazards.
■ Water and Moisture
Do not use this product near water - for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in
a wet basement, or near a swimming pool, and the like.
■ Placement
Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing
serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product
should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the
manufacturer.
■ Ventilation
Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product
and to protect it from overheating, and these openings must not be blocked or covered. The openings should
never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not
be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the
manufacturer’s instructions have been adhered to.
■ Power Sources
This product should be operated only from the type of power source indicated on the marking label. If you are
not sure of the type of power supply to your home consult your appliance dealer or local power company. For
products intended to operate from battery power, or other sources, refer to the operating instructions.
■ Grounding or Polarization
This product may be equipped with either a polarized 2-wire AC line plug (a plug having one blade wider than
the other) or a 3-wire grounding type plug, a plug having a third (grounding) pin. The 2-wire polarized plug
will outlet, try reversing the plug. If the plug still fails to fit, contact your electrician to replace your obsolete
outlet. Do not defeat the safety purpose of the polarized plug. The 3-wire grounding type plug will fit into a
grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact
your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug.
■ Power-Cord Protection
Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed
upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point
where they exit from the product.
■ Lightning
For added protection for this product during a lightning storm, or when it is left unattended and unused for
long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will
prevent damage to the product due to lightning and power-line surges.
■ Overloading
Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk
of fire or electric shock.
IMPORTANT SAFEGUARDS

3
■ A product and cart combination should be moved with care. Quick stops, excessive force, and
uneven surfaces may cause the product and cart combination to overturn.
■ Object and Liquid Entry
Never push objects of any kind into this product through openings as they may touch dangerous voltage
points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.
■ Servicing
Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous
voltage or other hazards. Refer all servicing to qualified service personnel.
■ Damage Requiring Service
Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following
conditions:
•When the power-supply cord or plug is damaged.
•If liquid has been spilled, or objects have fallen into the product.
•If the product has been exposed to rain or water.
•If the product has been exposed to rain or water.
•If the product does not operate normally by following the operating instructions. Adjust only those
controls that are covered by the operating instructions as an improper adjustment of other controls may result
in damage and will often require extensive work by a qualified technician to restore the product to its normal
operation.
•If the product has been dropped or damaged in any way.
•When the product exhibits a distinct change in performance - this indicates a need for service.
■ Replacement Parts
When replacement parts are required, be sure the service technician has used replacement parts specified
by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may
result in fire, electric shock or other hazards.
■ Safety Check
Upon completion of any service or repairs to this product, ask the service technician to perform safety checks
to determine that the product is in proper operating condition.
■ Heat
The product should be situated away from heat sources such as radiators, heat registers, stoves, or other
products (including amplifiers) that produce heat.

4
CAUTION
CAUTION:
TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK).
NO USER-SERVICEABLE
PARTS INSIDE. REFER
SERVICING TO
QUALIFIED SERVICE
PERSONNEL.
RISK OF
ELECTRIC SHOCK
DO NOT OPEN.
SA 1966
This symbol [crossed-out wheeled bin WEEE Annex IV] indicates separate collection of
waste electrical and electronic equipment in the EU countries.
Please do not throw the equipment into the domestic refuse.
Please use the return and collection systems available in your country for the disposal
of this product.
SA 1965
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to
alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to
persons.
The exclamation point within an equilateral triangle is intended to alert the user to the
presence of important operating and maintenance (servicing) instructions in the literature
accompanying the product.

5
WARNING:
TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR
MOISTURE.
The connection of a non-shielded equipment interface cable to this equipment will invalidate the FCC Certification or Declaration of
this device and may cause interference levels which exceed the limits established by the FCC for this equipment. It is the responsibility
of the user to obtain and use a shielded equipment interface cable with this device. If this equipment has more than one interface
connector, do not leavecables connected to unused interfaces. Changes ormodifications not expressly approved by the manufacturer
could void the user’s authority to operate the equipment.
FOR UNITED STATES USERS:
INFORMATION
This equipment has been tested and found to comply with thelimits for a Class A digitaldevice, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a
residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own
expense.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
FCC CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate
the equipment.
This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.
WARNING:
Handling the cord on this product or cords associated with accessories sold with this product, will expose you to lead, a chemical
known to the State of California to cause birth defects or other reproductive harm.
Wash hands after handling.

6
BEFORE YOU USE
When using this device, be sure to use the supplied power cord and AC adapter.
The power cord and AC adapter that come with this product are for this product only. Do not use them with
another product.
Be sure to use the power cord applicable to your local power specifications.
When storing the product, do not leave it under direct sunlight or by heaters. It may become discolored,
deformed, or damaged.
Do not place this product in any humid, dusty, salt bearing wind, or vibrating locations.
Only use it under the following environmental conditions:
Temperature: 0°C - 40°C (32°F - 104°F)
Humidity: 30% - 85% (No condensation)
Use a soft, dry cloth for cleaning
Do not use any volatile solvent such as thinner or benzene.
Do not point the camera lens directly at the sun. It may be damaged and you may not be able to take pictures.
Luminescent and Black Spots
There may be some pixels that do not properly operate due to the use of CMOS Area Image Sensors made-up
of many pixels.
Though luminescent or black spots may be found on the screen, it is a phenomenon peculiar to the CMOS Area
Image Sensors and is not a malfunction.
Follow the guidelines below to prevent the unit from dropping or overturning.
•Use the product on a stable base, desk, or table. Do not place the product on an unstable base or slanted
surface.
•Place or wire the unit to prevent the AC adapter cord or video cable from pulling.
Carry the product by holding the lower part of the main unit in both hands. Never hold the product by the column
or the camera head.
Pay careful attention when using (including setting-up and storing) or transferring the product to prevent the
camera head from receiving any shocks.
Do not look directly into the LED light. If you look directly into it at point-blank range, your eyes may be injured.
Some type of SD card/USB flash drive can be used.
Transfer the data from the SD card onto a device such as a PC to save a backup copy. Malfunction of the
product or repairs to it may cause the data saved in the SD card to be deleted.
If this product is used for longer than the warranty period, its performance and quality may deteriorate due to
the lifetime of its parts. To purchase replacement parts, consult the dealer from whom you purchased this
product or our branch/office near your location.
Battery precautions:
•If this product is not going to be used for a long time, take the batteries out of the remote control.
•Do not use rechargeable batteries (e.g., Ni-Cd (NiCad batteries)).
•Do not use new and old batteries or batteries of different types together.
•Do not try to recharge or short-circuit the batteries.
•When disposing of used batteries, follow the instructions of your local government.
•Insert from one side and pay particular attention to the polarity (+/- directions).
If any liquid from a battery leaks onto your skin or clothes, flush the area with clean water immediately. If it gets
into your eye, flush immediately with clean water and then contact a doctor.
Do not keep the batteries in the reach of children because there may be a choking hazard.
If a battery is swallowed, consult a physician immediately as this could result in asphyxiation or the battery may
become lodged in the stomach or esophagus.
Battery precautions <WARNING>
•A lithium coin battery is included in the product. Do not swallow the lithium coin battery. There is a risk of
injury due to chemical reactions.
•If the battery is swallowed, it can cause serious internal damage leading to death in less than two hours.
•If you have swallowed the battery, or if you suspect that the battery is somewhere in your body, seek medical
advice immediately
•Keep new and used batteries out of the reach of children.
•If the battery compartment of the remote control does not close tightly, stop using the remote control and
keep it out of the reach of children.
•Do not replace the wrong type of battery. It may cause an explosion.

7
•Do not expose the battery to excessively high temperature or low pressure at high altitude while using, storing
or carrying the battery.It may cause an explosion or the leakage of flammable liquid or gas
•Do not dispose of the battery in a fire or in a heated furnace. An explosion may occur.
•When disposing of the battery, follow the rules of the local government.
•Do not mechanically crush or cut the battery. An explosion may occur.
About using microphones
Connecting microphones other than electret condenser microphones (microphones for PCs and so on) could
cause a malfunction to occur. If you are concerned about this product’s operating noise when using the built-in
microphone, we recommend using an external microphone.
About the audio input port
Do not connect any audio line-output devices such as a CD/MP3 player to the audio input port when the Audio
Selector is set to “Mic-in.” Audio input is a dual purpose port (microphone/line-in) which supplies power when
“Mic-in” is selected, adding external output devices (CD/MP3) may damage them.
Menu
Some functions may not be set or operated depending on the mode or the menu settings being used.
Record/Play
•Before recording an important scene, make sure to do a test recording to confirm that the camera is working
properly.
•The maximum file size of the continuous recording is 2GB. (The maximum recording length varies depending
on other factors such as resolution and recording quality.)
•Movie files that are recorded with this camera or converted by the proprietary software can only be played
with this camera.
■Copyright
Do not commercially use or transfer movies or audio files recorded with the camera without the permission of
the copyright holder except for personal use.
Do not use the camera in locations where recording movies or audio files are prohibited.

8
CONTENTS
IMPORTANT SAFEGUARDS..................................................................................................................2
BEFORE YOU USE........................................................................................................................................6
CONTENTS ..................................................................................................................................8
1. BUNDLED ITEMS .........................................................................................................................10
2. BASIC OPERATIONS...................................................................................................................11
2-1 Document camera .............................................................................................................................11
Part names........................................................................................................................................... 11
Operating panel....................................................................................................................................12
Rear panel and cable connection.........................................................................................................13
Side panel............................................................................................................................................15
Moving parts of the document camera ..............................................................................................16
Output image size ...............................................................................................................................17
2-2 Supplied accessories ........................................................................................................................... 19
Remote control ....................................................................................................................................19
Preparation of the remote control ........................................................................................... 19
Operation of the remote control ................................................................................................. 19
Receiving IR signal from the remote control ......................................................................... 19
Fixture..................................................................................................................................................20
How to use the supplied fixture and cable tie...............................................................................20
2-3 Shooting images ..................................................................................................................................22
Setting up the product ....................................................................................................................... 22
Connecting the power cord ................................................................................................................. 22
Connecting the video cable................................................................................................................... 22
Turn on / off the power.......................................................................................................................... 23
Adjusting the size.................................................................................................................................. 24
Adjusting the brightness ...................................................................................................................... 25
Turning on / off LED lighting ................................................................................................................. 26
Selecting the image source ................................................................................................................ 27
Pausing the image................................................................................................................................ 27
Rotating the image................................................................................................................................ 28
Turning on / off the audio...................................................................................................................... 28
2-4 Configuring the setting ......................................................................................................................... 29
How to configure the setting................................................................................................................. 29
About Menus ...................................................................................................................................... 29
System Setting menu(1/4 page) ...................................................................................................... 31
System Setting menu(2/4 page) ...................................................................................................... 33
System Setting menu(3/4 page) ...................................................................................................... 35
System Setting menu(4/4 page) ...................................................................................................... 37
Full menu1 .......................................................................................................................................... 38
Compare Picture function ......................................................................................................... 38
PinP function .............................................................................................................................. 41
Full menu2 .......................................................................................................................................... 38
Highlight function ....................................................................................................................... 44
Mask function ............................................................................................................................ 45

9
3. ADVANCED OPERATIONS.......................................................................................................... 46
3-1 Using an SD card / USB flash drive ................................................................................................ 46
Recording............................................................................................................................................. 47
Still image.................................................................................................................................... 47
Video........................................................................................................................................... 48
Displaying the stored data .................................................................................................................. 49
Thumbnail display (list of still images / videos) ........................................................................ 49
Displaying a still image full-screen............................................................................................... 51
Playing a video full-screen........................................................................................................... 53
3-2 Using by connecting to a computer with the USB cable ................................................................... 56
Switching to the External input mode(External input screen) ...........................................................57
3-3 Using Miracast function ...................................................................................................................... 59
3-4 Displaying enlarged image using a microscope on .................................................................... 61
Procedure ........................................................................................................................................... 62
3-5 Firmware update procedure ................................................................................................................. 64
4. TROUVLE SHOOTING ............................................................................................................... 65
4-1 Symptoms and Confirmation................................................................................................................ 65
4-2 When you have a problem ............................................................................................................... 68
5. SPECIFICATIONS........................................................................................................................ 70
5-1 General ................................................................................................................................................ 70
5-2 Main Camera ....................................................................................................................................... 71
5-3 Illumination Device............................................................................................................................... 71
5-4 TRADEMARKS AND LICENSES .................................................................................................... 72

10
BUNDLED ITEMS
The items below are included with this product. If any item is missing, contact the
dealer from whom you purchased this product.
AC adapter AC cord
USB Type C-A cable Remote control
Coin battery
（For remote control）
Fixture× 2
（ For HDMI c a b l e ）
1
Cable tie x2
Quick start guide
IMPORTANT
SAFEGUARDS
Operation support sticker
3S Service registration
form
Product warranty
3S Service Registration
Statement
3S Assurance guarantee label
Document camera