Elo Touch Solutions E062324 User manual

© Copyright 2017 Elo Touch Solutions, Inc. 1
QIG600042 REV. A
E062324 ELO-STAND-SELF-SERVICE-DESKTOP
E062510 ELO-STAND-SELF-SERVICE-FLOOR EXT
E062704 KIT-EMV-CRADLE-VF-MX915-ING-ISC250
E062899 KIT-EMV-INGENICO IPP350 CRADLE-SS
ASSEMBLY INSTRUCTIONS, ELO SELF SERVICE STAND

© Copyright 2017 Elo Touch Solutions, Inc. 2
QIG600042 REV. A
Contents for kit:
E062324 ELO-STAND-SELF-SERVICE-DESKTOP Bag A:
SCREW, M4X10, ROUND-HEAD,
FLANGE, HEX
Qty. 2
Bag B:
SCREW, M4X10, FLAT-HEAD, HEX
Qty. 4
Bag C:
SCREW, M3X8, PAN-HEAD,
CROSS-RECESS
Qty. 3
Tie-wrap
Qty. 2

© Copyright 2017 Elo Touch Solutions, Inc. 3
QIG600042 REV. A
Remove and save (2) screws on
rear of stand with provided hex
wrench, pull out printer tray.
Add (2) screws from bag “A”;
leave ~3mm (1/8”) gap for stand.
Gap
Align slots on bottom rear of stand with (2) screws on base and
slide on stand. Add (4) screws from bag “B”. Tighten (2) screws at
rear.
For Floor Stand, go to step 4
For Countertop Stand, continue to step 2Continue to step 12 for Countertop Stand
1 2
3

© Copyright 2017 Elo Touch Solutions, Inc. 4
QIG600042 REV. A
Assemble base plate to tower
using (6) screws from bag “K”.
Remove and save (4) hex-head screws on
the left and right of the stand with provided
hex wrench. Pull off the silver cover and set
aside.
Continue to step 6for Floor Stand
54

© Copyright 2017 Elo Touch Solutions, Inc. 5
QIG600042 REV. A
Add (2) screws from bag “A”;
leave ~3mm (1/8”) gap for stand.
Gap
Align slots on bottom rear of stand with (2) screws
on base and slide on stand. Add (4) screws from
bag “B”. Tighten (2) screws at rear.
Continue to step 8for Floor Stand
76

© Copyright 2017 Elo Touch Solutions, Inc. 6
QIG600042 REV. A
Add power strip brackets (supplied with
power strip) using (2) screws from bag
“L”. Hook one side of power strip onto
brackets than push to snap down.
Add power bricks into tower
using provided straps.
Continue to step 10 for Floor Stand
9
8

© Copyright 2017 Elo Touch Solutions, Inc. 7
QIG600042 REV. A
(2) bolt holes available on top of base to
secure stand to floor. Feet can be adjusted
in case of uneven surfaces.
Replace floor stand cover and secure
using (4) screws saved from step 4.
Continue to step 12 for Floor Stand
11
10

© Copyright 2017 Elo Touch Solutions, Inc. 8
QIG600042 REV. A
Remove and save (2) hex-head screws using provided
hex wrench. Open display mount and support with kick-
stand. Kick-stand
Assemble (2) screws from bag “I” to
top VESA mount hole on back of I-
Series. Assemble display to top
slotted holes on stand bracket. Add
remaining (2) screws to bottom VESA
mount
Assemble bottom (2) VESA
mount screws from back
side.
For adding EMV Mount to Desk/Floor Stand, go to step 15
For NO EMV Mount, continue to step 13 Continue to step 14
1312

© Copyright 2017 Elo Touch Solutions, Inc. 9
QIG600042 REV. A
Route needed cables from I-Series
through stand.
Add tie-wrap
Continue to step 31 for Countertop Stand
14

© Copyright 2017 Elo Touch Solutions, Inc. 10
QIG600042 REV. A
Assemble iPP350 to bracket using hook
on bracket and (2) screws from bag “J”.
For Ingenico iPP350 EMV Cradle (E062899), go to
step 15
For Verifone MX915 /Ingenico iSC250 EMV Cradle
(E062704), go to step 23
Add cable to iPP350.
Add tie-wraps
Route terminal cable through bracket.
15
16

© Copyright 2017 Elo Touch Solutions, Inc. 11
QIG600042 REV. A
Assemble EMV Cradle assembly to 22” I-Series using (4)
screws from bag “I”.
(EMV terminal cable to exit hole)
Remove (2) screws and take off cable cover.
Leave gap
Assemble (2) screws from bag “I” (in Countertop Stand kit)
to top VESA mount hole on back of 22” I-Series.Assemble
display to top slotted holes on stand bracket.Add remaining
(2) screws from bag “I” to bottom of mount.
17
18
19
Continue to step 20

© Copyright 2017 Elo Touch Solutions, Inc. 12
QIG600042 REV. A
Add needed cables to 22” I-
Series; Route cables
through slot in stand bracket
to 22” I-Series connectors.
Blue = 22" I-Series cables
Green = EMV terminal cable
Route EMV / 22" I-
Series cables through
stand.
Add tie-wrap
Assemble left and right doors
using provided hex wrench.
Continue to step 31
20
2221

© Copyright 2017 Elo Touch Solutions, Inc. 13
QIG600042 REV. A
Remove and save (4) screws and take off cover.
Add bracket to stand using (4) screws from bag “F”.
Add (3) screws for mounting EMV terminal:
- Use bag “G” for Ingenico iSC250
- Use bag ”H” for Verifone MX915
Screw
locations
for
Verifone
MX915
Screw
locations
for
Ingenico
iSC250
Continue to step 26
23 25
24

© Copyright 2017 Elo Touch Solutions, Inc. 14
QIG600042 REV. A
Attach EMV terminal cable and
slide terminal onto bracket.
(EMV terminal cable)
EMV terminal cable:
Ingenico iSC250
Verifone MX915
Route EMV terminal cable, and
assemble cover onto bracket.
Continue to step 28
2726

© Copyright 2017 Elo Touch Solutions, Inc. 15
QIG600042 REV. A
22" I-Series Android
22" I-Series Windows series
Assemble (2) screws from bag “I”
to top VESA mount hole on back
of 22" I-Series. Assemble display
to top slotted holes on stand
bracket.
Add remaining (2) screws from bag “I” to
bottom VESA mount.
Continue to step 30
2928

© Copyright 2017 Elo Touch Solutions, Inc. 16
QIG600042 REV. A
Route needed cables from 22" I-Series /
EMV terminal through stand.
Add tie-wrap
Add tie-wrap
Continue to step 31
30

© Copyright 2017 Elo Touch Solutions, Inc. 17
QIG600042 REV. A
Add (2) screws from bag “C” to printer
tray; use Star printer bracket to set
depth of screws than remove Star
bracket.
Continue with step 31 for Star printers.
For Epson TM-T88, go to step 34. Add Star printer bracket to printer; refer to Star
instructions.
Add Star printer with bracket to printer tray. Secure
printer to printer tray using 3rd screw from bag “C”.
Continue to step 35
33
32
31

© Copyright 2017 Elo Touch Solutions, Inc. 18
QIG600042 REV. A
Add (4) screws from bag “D” to attach printer to the tray.
Epson TM-T88
34

© Copyright 2017 Elo Touch Solutions, Inc. 19
QIG600042 REV. A
Route cables from/to printer as needed, slide in
printer tray assembly Add (2) screws saved from step 1 to secure printer assembly and (2) screws saved from step 12 to secure 22” I-Series
bracket.
3635

© Copyright 2017 Elo Touch Solutions, Inc. 20
QIG600042 REV. A
For more information, go to www.elotouch.com/support, or call the office nearest you.
Elo reserves the right to change or update, without notice, any information contained herein; to change, without notice, the design, construction,
materials, processing or specifications of any products; and to discontinue or limit production or distribution of any products. Elo and the Elo logo
are either trademarks or registered trademarks of Elo Touch Solutions, Inc. All other trademarks are the property of their respective owners.
© 2017 Elo Touch Solutions, Inc. All rights reserved. QIG600042