Elvaco CMi4110 User manual

INTRODUCTION
CMi4110 is an integrated meter connectivity module mounted inside
a Landis+Gyr UH50 meter / UC50 calculator to deliver meter data via
a LoRaWAN network. For a complete description of the product or
for information in other languages, please visit the Elvaco AB website,
http://www.elvaco.com.
CMi4110 / WZU-LR
Integrated MCM for Landis+Gyr UH50/UC50, LoRaWAN
INITIAL DATA RATE CALIBRATION
When activated, CMi4110 will initially transmit messages every minute
in order to let the LoRaWAN network adjust to an optimal data rate.
After 2 minutes, the module will start using its normal settings where the
message transmit interval is determined by the device conguration.
DEVICE CONFIGURATION
Before activating the module, you should make sure to apply the correct
conguration prole by using the Elvaco mobile application. Settings are
transferred to the device using NFC.
Join EUI - The Join EUI sets the identication number of the application
server where data from the module shall be delivered. The JoinEUI is by
default set to 0000000000000000 in all CMi4110 modules.
Activation type - There are two dierent activation types for LoRaWAN
- Over-the-air activation (OTAA) and Activation by personalization
(ABP). Elvaco strongly recommends using OTAA, where all network keys
are generated each time the module joins the LoRaWAN network. In
contrast, for ABP, all keys are set manually and stay constant over time.
Application key - The application key of each CMi4110 device is
generated by Elvaco and used in OTAA mode to generate network keys
when the module joins the LoRaWAN network. Keys are managed in a
secure way using Elvaco’s OTC (One Touch Commissioning) solution
which includes the mobile application for conguration.
Message format - CMi4110 supports four dierent message types:
Standard, Compact, JSON and Scheduled-daily redundant. Please refer
to the CMi4110 user’s manual for more information about the structure
and payload of each message format.
Transmit interval - The transmit interval parameter is used to set how
often the module transmits messages.
EcoMode - EcoMode can be enabled to achieve a battery-life of 11 years.
The EcoMode table is then used to determine how often the module
is allowed to transmit data for each data rate. If the transmit interval
exceeds the limit in the EcoMode table, it will be lowered accordingly.
Configuration lock - CMi4110 has a conguration lock feature which
can be used to prevent unauthorized users to access the module. When
conguration lock has been enabled, a user needs the device-specic
Product Access Key in order to access the device. Keys are managed
in a secure way using Elvaco’s OTC solution which includes the mobile
application for conguration.
After you have set all conguration parameters, place the phone with
the back facing the right side of the meter, parallel to the module, and
click Apply settings. Hold the phone still until it vibrates three times.
This conrms that new settings have successfully been transferred to the
device via NFC.
MOUNTING
CMi4110 is mounted in module slot 2 (right slot) of a Landis+G
yr UH50 meter with software version 5.15 or higher or a UC50
calculator with software 8.06 or higher. Grab the device by the
outer edges and gently press it into position.
NOTE
Electrostatic-sensitive device. Please observe
the necessary ESD protective measures when
installing the module.
ANTENNA
CMi4110 is available in two dierent versions. CMi4110Int uses an
internal PCB antenna. CMi4110Ext is equipped with a SMA connector (6)
to connect an external antenna.
NOTE
Make sure to mount the antenna at least 0.5 meters away from the
meter.
ACTIVATION
Upon delivery, CMi4110 is set to passive mode, which means no
messages will be transmitted from the module. The module can be
activated in one of the following ways:
By using the module push button: Press and hold down the push
button (2) for at least 5 seconds until the green LED lights up.
By using the Elvaco OTC App: Open the Elvaco OTC app
(downloadable in Google Play) and scan the module (make sure NFC
is activated on the phone). Remove the front enclosure of the meter if
needed. Go to Apply mode, set the Power mode to “active” and click
Apply settings. Place the phone with the back facing the right side of the
meter, parallel to the module. New settings are applied via NFC.
Upon start-up, the green and the red LEDs will lighten up for one
second. The module will thereafter attempt to join the LoRaWAN
network. Each attempt is marked by a short blink of the green LED. Upon
a successful join attempt, the green LED will lighten up for 8 seconds.
If the module fails to join the LoRaWAN network 6 times, it will wait for
one hour before a new join attempt is performed in order to conserve
battery. A new join attempt cycle can be initiated manually by using the
push button (2).
1. Meter Interface
2. Push Button
3. Green LED
4. Red LED
5. Tamper Switch (optional)
6. External antenna
connector (optional)
7. LoRaWAN antenna
8. NFC antenna

© 2022, Elvaco AB. All rights reserved. The documentation and product are provided on an “as is” basis only and may contain deciencies or in-
adequacies. Elvaco AB takes no responsibility for damages, liabilities or other losses by using this product. No part of the contents of this manual
may be transmitted or reproduced in any form by any means without the written permission of Elvaco AB. Printed in Sweden.
CMi4110 Quick Manual English
Version: 2.1
SERVER CONFIGURATION
Before CMi4110 is able to transmit messages via the LoRaWAN network,
device information needs to be added to the network server. More
specically, the following parameters needs to be registered (in OTAA
mode) in order to enable the network server to receive messages from
the module:
• Device EUI (16-digit number printed on the device label)
• Application key
• Join EUI
NOTE
If activation mode is set to “ABP”. the application key does not need to
be added to the network server. Instead, the following information will
be needed: Network session key, Application session key and Device
address.
TECHNICAL SPECIFICATIONS
Mechanics
Dimensions 80 x 38 x 23 mm
Weight 35 g
Mounting In module slot 2 of Landis+Gyr
UH50 / UC50
External antenna connector SMA female
Electrical connections
Supply voltage Internal meter battery (D cell) or
PSU (Elvaco: CMip2110 230V,
Landis+Gyr WZU-AC230-xx or
WZU-ACDC24-00)
Electrical characteristics
Nominal voltage 3.0 VDC
Power consumption (max) 40 mA
Power consumption (sleep mode) ~2.2 µA
Environmental specifications
Operating temperature +5 °C to +55 °C
Operating humidity 0 - 93 % RH, no condensation
Operating altitude 2000 m
Usage environment Indoors
Storage temperature -20 °C to +60 °C
Radio characteristics
Frequency 868 MHz
Output power 14 dBm
Receiver sensitivity -135 dBm
LoRaWAN characteristics
Device class Class A, Bi-directional
LoRaWAN version 1.0
Activation OTAA or ABP
Data rate DR0-DR5 (250 bit/s-5470 bit/s)
User Interface
Green LED Start-up / reboot / switch-o
indicator
Red LED Start-up / reboot / switch-o
indicator
Push Button Start-up / reboot / switch-o
Conguration NFC via Elvaco OTC app or
downlink data
Approvals
EMC EN 301 489-1, EN 301 489-3
SIMPLIFIED DECLARATION OF CONFORMITY
Hereby, Elvaco declares that the product is in compliance with the
following directives:
EU:
- 2014/53/EU (RED)
- 2014/30/EU (EMC)
- 2011/65/EU + 2015/863 (RoHS)
UK:
- 2017No. 1206
- 2016 No. 1091
- 2012 No. 3032
The complete Declaration of Conformity can be found at www.elvaco.
se/en > Search on product.
SAFETY
The warranty does not cover damage to the product caused by usage in
any other way than described in this manual. Elvaco AB can not be liable
for personal injury or property damage caused by usage in any other way
than described in this manual.
CONTACT INFORMATION
Elvaco AB Technical support:
E-mail: [email protected]
Online: www.elvaco.com