Elvaco CMi6140 User manual

MOUNTING
Before mounting the module in the meter, make sure that a SIM card is
installed in the SIM card slot.
NOTE! Please note that the SIM card must be inserted correctly. If it
is inserted upside down it can easily damage the SIM slot.
CMi6140 is mounted in the module slot of a Kamstrup Multical meter. Hold
the device by the outer edges and gently press it into position
NOTE
• Electrostatic-sensitive devices. Please observe the
necessary ESD protective measures when installing
the device.
ANTENNA
CMi6140 is available with external antenna. The antenna is connected using
an MCX connector.
NOTE
• The antenna should be mounted at least 0.5 meter away from the
meter to avoid interference.
POWER SUPPLY
The meter where CMi6140 is installed in must use any of
Kamstrup 230V High Power
Kamstrup 24V High Power
Kamstrup IoT battery, D-cell
Kamstrup IoT battery, C-cell
INTRODUCTION
CMi6140 is an integrated meter connectivity module mounted inside a
Kamstrup MULTICAL 403/603/803 that deliver meter data to a receiving
system via a NB-IoT network. For a complete description of the product,
or for information in other languages, please visit the Elvaco AB website,
https://www.elvaco.com.
MODULE SPECIFICATION
CMi6140
Integrated MCM for Kamstrup MULTICAL 403/603/803, NB-IoT
ACTIVATION
Upon delivery, CMi6140 has a standard conguration. If you would like
to change conguration, please download the Elvaco OTC Application
(One-Touch commissioning) for Android available in Google Play or for iOS
available in App Store.
The Elvaco OTC connects to the module via NFC.
By default, the product is set to passive mode, which means no
messages will be transmitted from the device. There are two ways to
activate the product:
1. By using the front buttons of the Kamstrup Multical meter.
-On Kamstrup Multical 403: press down both front buttons
simultaneously until “CALL” is displayed on the meter display.
-On Kamstrup Multical 603 and 803: press down both arrow
buttons simultaneously until “CALL” is displayed on the meter
display.
2. Via the Elvaco mobile application.
Go to the Apply tab, set the Power mode to “Active”, push “Apply”
and place the phone on the right side of the meter, next to the
module. Make sure to hold the phone still until the phone vibrates.
You can make sure that the module has joined the NB-IoT network correctly
by checking the “connection” eld in the Inspect tab of the OTC App. The
mobile phone should vibrate three times. This indicates that settings have
successfully been applied.
For more detailed infromation about activation and operation see Users
Manual available on www.elvaco.se
NOTE
• Make sure to locate the NFC antenna on your phone. When you scan or
write new congurations to the module, you should place the phone’s
NFC antenna as close as possible to the NFC antenna of the module.
1. Antenna Connector (MCX female)
2. Meter Interface
3. Pulse Inputs
4. NFC Antenna
5. SIM (nano)

© 2022, Elvaco AB. All rights reserved. The documentation and product are provided on an“as is” basis only and may contain deciencies or inadequacies.
Elvaco AB takes no responsibility for damages, liabilities or other losses by using this product. No part of the contents of this manual may be transmitted
or reproduced in any form by any means without the written permission of Elvaco AB. Printed in Sweden.
CMi6140 Quick manual English
Version: 1.4
SAFETY
The following safety precautions must be observed during all phases of the operation, usage, service or repair of any CMi Series product. Users of the
product are advised to convey the information to users and operating personnel and to incorporate these guidelines into all manuals supplied with the
product. Failure to comply with these precautions violates safety standards of design, manufacture and intended use of the product. Elvaco AB assumes
no liability for customer’s failure to comply with these precautions.
CMi6140 receives and transmits radio frequency energy while switched on. Remember that interference can occur if the product is used close to TV sets,
radios, computers or inadequately shielded equipment. Follow any special regulations and always switch o the product wherever forbidden, or when
you suspect that it may cause interference or danger.
The device or antenna of the product must not be mounted closer than 0.5 m from areas where people are staying permanently in order not to risk
exposing people to RF elds.
To use the product’s NFC TAG, follow the instructions issued by the manufacturer of the NFC reader for safe and ecient operation.
Ensure yourself that power supply and/or battery-unit connected to CMi6140 full EN 62368-1 or equivalent safety standard.
For guaranteed lifetime of a battery-operated device, conguration and settings must be approved by Elvaco and not changed during the lifetime of the
device.
TECHNICAL SPECIFICATIONS
Mechanics
Dimensions (w x h x d) 90 x 35 x 12 mm
Mounting In module slot of Kamstrup Multical®
403/603/803
External antenna
connector
MCX (female)
SIM card Slide, size Nano
Electrical connections
Supply voltage HC99303 230 VAC high power supply
HC99305 D-cell battery IoT
HC99306 C-cell battery IoT
Electrical characteristics
Nominal voltage 3.5 VDC
Power consumption (max) 300 mA
Power consumption (sleep
mode)
8µA
Environmental specications
Operating temperature +5 °C to +55 °C
Operating humidity 0 - 93 % RH, no condensation
Operating altitude 2000 m
Pollution degree Degree 1
Usage environment Indoors
Storage temperature -20 °C to +60 °C (Module)
Mobile network
Band 20, 8, 3
3GPP Release 14 (NB2)
User interface
Conguration • NFC via Elvaco OTC App
• Via LwM2M (Elvaco Evo DM-system,
or third-party DM-system)
• Precong on delivery
CONTACT INFORMATION
Elvaco AB Technical support:
Phone: [phone]
E-mail: suppor[email protected]om
Online: www.elvaco.com