Emerson Fisher FIELDVUE DVC6200 SIS User manual

www.Fisher.com
Use these instructions to mount a FIELDVUE™
DVC6200/DVC2000 to a Linear Side Mount Actuator
WARNING
Avoid personal injury or property
damage from sudden release of process
pressure or bursting of parts. Before
performing any maintenance
operations:
Always wear protective clothing,
gloves, and eyewear.
Do not remove the actuator from
the valve while the valve is still
pressurized.
Disconnect any operating lines
providing air pressure, electric power, or
a control signal to the actuator. Be sure
the actuator cannot suddenly open or
close the valve.
Use bypass valves or completely
shut off the process to isolate the valve
from process pressure. Relieve process
pressure from both sides of the valve.
Vent the pneumatic actuator
loading pressure and relieve any
actuator spring precompression.
Use lock-out procedures to be sure
that the above measures stay in effect
while you work on the equipment.
Check with your process or safety
engineer for any additional measures
that must be taken to protect against
process media.
Refer to the appropriate actuator instruction manual
for actuator installation, operation, maintenance, and
parts identification as this manual
may or may not
include all components shown for kit installation.
1. Isolate the control valve from the process line
pressure and release pressure from both sides of the
valve body. Shut off all pressure lines to the actuator,
releasing all pressure from the actuator. Use lock-out
procedures to be sure that the above measures stay in
effect while you work on the equipment.
2. Install arm connector to stem block using
provided hardware. The slots are to provide fine
adjustment for the array.
Mounting Instructions
D103998X012
June 2014
DVC6200/DVC
2000
Digital Valve Controller
Linear Actuator
Side Mount

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014
3. Attach arm extension to arm connector with
supplied fasteners.
4. Install the array to the arm extension with the
provided M4 fasteners.
5. Attach mounting bracket to yoke with the
supplied hardware.

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014
6.
Array Alignment
Ensure device mounting plane is perpendicular to
array.
6a. Attach alignment template to mounting bracket.
Adjust array to line up with alignment template. If
Actuator stroke is in the up position, use Step 6b. If
Actuator stroke is in the down position, use Step 6c.
Ensure that the index mark of the alignment tool will
be in between the array index marks.
(Array Kit sold separately)
(Index Lines are shown below with arrows)
6b. Align array bottom index line with alignment
template index line.
6c. Align array top index line with alignment template
index line.

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014
6d. Align array laterally with the alignment template.
6e. Tighten all fasteners to lock array into position.
Loctite® Thread Locker 242®is recommended but not
supplied.
7. Remove alignment tool, and attach device to
mounting bracket with supplied M8 fasteners.

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014

DVC6200/DVC2000
Digital Valve Controller on
Linear Actuator
Mounting Instructions
D103998X012
June 2014
Neither Emerson, Emerson Process Management, Fisher, nor any of their affiliated entities assumes responsibility for the selection, use and
maintenance of any product. Responsibility for the selection, use and maintenance of any product remains with the purchaser and end user.
Fisherand FIELDVUE are marks owned by Fisher Controls International LLC, a member of the Emerson Process Management business unit of Emerson Electric
Co. Emerson Process Management, Emerson, and the Emerson logo are trademarks and service marks of Emerson Electric Co. All other marks are the
property of their respective owners.
The contents of this publication are presented for informational purposes only, and while every effort has been made to ensur
e their accuracy, they are not to
be construed as warranties or guarantees, express or implied, regarding the products or services
described herein or their use or applicability. We reserve the
right to modify or improve the designs or specifications of such products at any time without notice.
Emerson Process Management
Marshalltown, Iowa 50158 USA
Sorocaba, 18087 Brazil
Chatham, Kent ME4 4QZ UK
Dubai, United Arab Emirates
Singapore 128461 Singapore
www.Fisher.com
______________________________________________________________________________________________________
© 2014 Fisher Controls International LLC. All right reserved.