Emerson 2100 User manual

2100 Series Emergency Pressure Relief Vent and
Manhole Cover (ATEX Approved)
Table of Contents
Introduction..................................................................1
Specifications .............................................................. 2
Product Identification and Marking .............................. 3
Principle of Operation.................................................. 4
Installation ...................................................................5
Startup..........................................................................6
Maintenance................................................................7
▲ WARNING
Failure to follow these instructions or
to properly install and maintain this
equipment could result in an explosion,
re and/or chemical contamination
causing property damage and personal
injury or death.
Enardo™ emergency pressure relief
vent must be installed, operated
and maintained in accordance with
federal, state and local codes, rules
and regulations and Emerson Process
Management Regulator Technologies
Tulsa, LLC instructions.
Failure to correct trouble could result in
a hazardous condition. Call a qualied
service person to service the unit.
Installation, operation and maintenance
procedures performed by unqualied
person may result in improper adjustment
and unsafe operation. Either condition
may result in equipment damage or
personal injury. Only a qualied person
shall install or service the emergency
pressure relief vent.
Introduction
Scope of the Manual
This Instruction Manual provides instructions
for installation, maintenance and parts ordering
information for the 2100 Series Emergency Pressure
Relief Vent.
Product Description
The 2100 Series Emergency Pressure Relief Vent is
designed to provide simple, reliable operation as an
emergency vent, while providing e󰀩cient access to
your tank and maintaining the industry leading sealing
standards (1 SCFH at 90% set point). It also provides
trouble free operation with a minimum maintenance.
There are two available congurations for 2100 Series:
tethered and restrained (see Figure 3).
Figure 1. 2100 Series
Instruction Manual
D103823X012 2100 Series
December 2021
North America Only

Specications
The Specications section lists the specications for the 2100 Series. The following information are stamped on
the nameplate attached to the relief vent: model number, connection size, date of manufacture, serial number,
pressure setting and ow rate.
Connection Sizes Available
16, 20 and 24 in. / 387, 489 and 591 mm
Pressure Ranges(1)
0.7 to 8.0 oz./sq. in. and 1.2 to 14.0 in. w.c.
Construction Materials
Base: Carbon steel, 304 Stainless steel and
316 Stainless steel
Lid and Seal Support: Aluminum, 304 Stainless
steel and 316 Stainless steel
Construction Materials (continued)
Seal: Buna-N, FEP Teon®and Viton®
Certication
EN IEC 60079-0:2018
EN IEC 60079-11:2012
EN ISO 80079-36:2016
EN ISO 80079-37:2016
1. The pressure limits in this Instruction Manual and any applicable standard or code limitation should not be exceeded.
Figure 2. 2100 Series Model Number Identification
TETHERED
RESTRAINED
Figure 3. 2100 Series Product Configurations
Teon®and Viton®are marks owned by E. I. du Pont de Nemours and Co.
Connection Size
(16, 20 and 24 in.)
Base
2. Carbon steel
3. 304 Stainless steel
4. 316 Stainless steel
5. Exotic
Lid
1. Aluminum
2. Carbon steel
3. 304 Stainless steel
4. 316 Stainless steel
5. Exotic
Gasket
T. Teon®
N. Buna-N
V. Viton®
X. Special
Pressure Settings
n - in. w.c. 0.7 to 8.0
z - oz./sq. in. 1.2 to 14.0
Options
1. Special Coating
2. Optional Hardware
2 1
Bolt Pattern
1. ANSI
2. API (20 and
24 in. only)
2
2100 Series
North America Only

RESTRAINED CONFIGURATIONTETHERED CONFIGURATION
Product Identication and Marking
Hazardous Locations
Enardo™ Emergency Pressure Relief Vents are
available with outer housings of Carbon steel, stainless
steel or aluminum, as indicated in Figure 5.
Tagging Information
The nameplate is located on the unit’s base, above the
connection ange (see Figure 5).
Nameplate Information
A nameplate is attached to the vent and contains the
following information:
• Model Number – Ex. 2124-24T-1
NAMEPLATE LOCATION
Figure 5. Product Identification and Marking
HAZARDOUS LOCATION
OUTER HOUSING OF STAINLESS STEEL,
CARBON STEEL OR COATED ALUMINUM
OUTER HOUSING OF UNCOATED ALUMINUM
Figure 4. Operational Schematics
II 1 G Ex h IIC T6 Ga
II 2 G Ex h IIC T6 Gb
• Connection Flange Size – 24 in. / 610 mm
• Serial Number
• Tag Number (Optional)
• Notied Body Number – Ex. 2460
• Cat. No. (Category Number)
- Category 1 – Stainless steel, Carbon steel or
Coated Aluminum vents
- Category 2 – Uncoated Aluminum vents
• Date – Date of Manufacture
• Certicate – Ex. PRESAFE 17 ATEX 10273X
• Pressure Setting and Flow Rate
- Setting – Ex. Z4.0
- Flow Rate SCFH (Air) – Ex. 00000
3
2100 Series
North America Only

Principle of Operation
The 2100 Series maintains a tight seal until system
pressure exceeds the set pressure of the vent. To adjust
the set pressure, a series of weights may be stacked
onto the lid assembly. When excessive overpressure
occurs the weighted lid assembly lifts, breaking the seal
between the seat and seal portion of the lid assembly.
This allows vapors to pass through the vent orice and
relieve pressure buildup. The vent reseals upon relief
and remains sealed; tethered lids may blow completely
o󰀨 in a catastrophic pressure event (see Figure 4).
It is important to know that relieving vapors near the
set pressure in a continuous manner may cause the
lid assembly to utter or oscillate. This is a common
occurrence in products of this type in the industry.
Operating the vent with utter or oscillation over time
may cause premature vent damage or wear. Please
feel free to contact your local Sales O󰀩ce with any
questions or for information on proper tank venting.
Figure 6.Recommended Seal Protection
Figure 7. Recommended Lifting Configuration
▲ WARNING
Wear protective gloves and clothing
to prevent skin contact when handling
lead weights. Wear eye protection. Avoid
breathing dust, fumes, mist, vapors and
spray. Do not eat, drink or smoke while
using the product. Avoid release to the
environment. Wash hands with soap and
water after handling. Keep away from
excessive heat and open ames.
▲ WARNING
Make sure line is free of hazardous vapors
before installing or servicing the valve.
4
2100 Series
North America Only

Figure 8. Installation Configuration
Installation
▲ WARNING
The 2100 Series is shipped with its lid
held partially open. The lid assembly has
attached weights and is heavy. Use caution
when removing the shipping blocks and
metal bands to avoid injury to ngers
and hands.
Prior to installation, remove the unit from its crate
and discard any protective coverings. Follow the
recommended instructions for the installation of the
2100 Series.
1. Carefully remove the 2100 Series from its crating.
Note
The seal portion of the vent can be
damaged through improper handling,
protect this surface with a padding
material while transporting the unit
if possible.
▲ WARNING
Failure to use spreader bar in lifting the
unit may result in personal injury, damage
to the unit and damage to the equipment.
Figure 9. Final Installation
There should be no tension on the
lanyards if the unit is to be hoisted in
position, failure to do so may result in
damage to the unit.
2. Use an appropriate spreader bar when lifting
the unit by the installed eyebolts. If the complete
unit is to be hoisted into position using installed
eyebolts, rst secure the base to the lid so that
there is no tension on the lanyards. Lanyards are
load-rated to 350 lbs / 160 kg each; damage to
other components may occur.
3. Install the 2100 Series on ange bolt patterns that
match that of the vent itself. If a matching pattern
is not available, please contact your local Sales
O󰀩ce for an adapter. The attachment ange
base must be a level surface. Use an appropriate
gasket placed between the 2100 Series ange and
the attachment ange, center the vent into place.
4. Insert the appropriate number of bolts and make
sure the vent is fastened securely. Installed bolts
should be clear of the lid assembly when it is in
the full open position. Remove any spacer or seal
protection and inspect the now installed unit for
items that would keep it from working properly.
The sealing area should be free of any debris or
damage that would cause leakage.
5
2100 Series
North America Only

1. Remove the nylock nut and outer fender
washer. The loop slides o󰀨 the lanyard
attachment assembly.
2. Grip lid rmly and lift straight up until the bottom of
guide assembly clears the base or attach shackles
to the eyebolts and use a crane or hoist to lift.
Note
Be careful to keep the guide from denting
or scratching the sealing surface as this
can cause leaks.
Startup
▲ WARNING
Ensure the tank is at atmospheric pressure
before opening. A pressure buildup inside
the tank can cause a spray to be emitted
from the vent if opened under pressure.
Tethered Conguration
1. Grip lid rmly and lift straight up until the bottom of
guide assembly clears the base.
Note
Be careful to keep the guide from denting
or scratching the sealing surface as this
can cause leaks.
2. Move the lid away from the opening and set it
down on the guide assembly. The guide assembly
is designed to hold the cover assembly even at the
maximum 8 oz./sq. in. setting.
Restrained Conguration
3. Move the lid away from the opening set it down.
The guide assembly is designed to hold the cover
assembly even at the maximum 8 oz./sq. in. setting.
6
2100 Series
North America Only

Maintenance
Sealing Surface Protector
▲ WARNING
The sealing surface protector must be
removed before the 2100 Series is returned
to service. The vent will not seal with the
protector in place.
The following instructions are applicable only if the
sealing surface protector was also purchased for your
unit. This guard is available to prevent damage to the
sealing surface when the 2100 Series is being used
for tank access or for running air or weld leads into
the tank.
Figure 10. Surface Protector Installation Figure 11. Surface Protector Cross-Section
Remove the sealing surface protector from its bag.
Place one end of the protector over the machined
surface with the legs pointing down and the at side
up. Firmly press the protector over the sealing surface.
Move around the sealing surface making sure the
protector is snugly attached.
Seal Replacement Procedure
Tools and Supplies Needed:
• 2 standard 7/16 in. wrenches
• Torque wrench (recommended)
• 1 screwdriver, any type (for eyebolt units only)
• Adhesive tape (recommended for eyebolt units)
• 2100 Series seal
• 4-1/4 in. stat-o-seals (recommended)
Replacement Procedure:
▲ WARNING
Ensure the tank is at atmospheric pressure
before opening. A pressure buildup inside
the tank can cause a spray to be emitted
from the vent if opened under pressure.
1. Remove the Nylock nut and outer fender washer.
The loop slides o󰀨 the lanyard attachment
assembly. Remove the lid assembly from the base
and place on a level surface.
2. Loosen the 4 hex nuts on the bottom of the lid
assembly. If the unit is equipped with eyebolts,
insert the screwdriver through the eye to
provide leverage.
7
2100 Series
North America Only

5. Remove the hex nuts, washers, guide assembly,
stat-o-seals, seal support and seal. Take note of
the order in which the components are removed.
3. If the unit is equipped with eyebolts, place a
piece of adhesive tape over the hex bolt heads to
prevent them from falling out. This is not required,
but makes seal replacement much easier.
6. Discard seal. If replacement stat-o-seals were
ordered, discard old stat-o-seals.
7. Reassemble the lower lid components in the
reverse order of disassembly.
8. Before tightening hex nuts, ensure that the eyelet
on the lanyard(s) is pointing away from the
center of the lid. Failure to do this may result in
damage to the tank by preventing the unit from
opening fully in a pressure event. Tighten each nut
to 1 turn after snug.
9. Flip the lid assembly over so that the guide
assembly is facing down. Reinsert the lid into the
base and reattach the lanyard(s). Do not tighten
the hex nut and the nylock nut greater
than 12 ft•lbf.
4. Flip the lid assembly over so that the guide
assembly is facing up.
8
2100 Series
North America Only

19
18
4
17
2
3
5
8
15
9
10
7
16 12
13
6
11 14
8
7
8
7
8
10
13
1
RESTRAINED BASE (COVER ASSEMBLY NOT SHOWN)
Figure 12. 2100 Series Assembly Drawing
9
2100 Series
North America Only

Teon®and Viton®are marks owned by E. I. du Pont de Nemours and Co.
Table 1. 2100 Series Seal Options
Table 2. Torque Specifications – Raised Face Flange, Steel Only
MATERIAL
GASKET AND SEAL OPTIONS
Part Number
16 in. 20 in. 24 in.
Buna-N NE3043037A0 NE3043040A0 NE3043043A0
Teon®NE3043038A0 NE3043041A0 NE3043044A0
Viton®NE3043039A0 NE3043042A0 NE3043045A0
NOMINAL PIPE DIAMETER NUMBER OF BOLTS BOLT DIAMETER TORQUE
in. mm ft-lbs N•m
16 16 1.00 25.4 159 216
20 20 1.13 28.7 214 290
24 24 1.25 31.8 253 343
Assumptions:
Use of SAE grade 5 bolts or studs or stronger.
No lubricant.
Compressed mineral fiber material or similar
Notes:
If lubricant is used on bolts, apply torque reduction factor listed in Lubricant Table.
For best results hardened steel washers should be used on all cast flange bolted connections.
Parts Ordering
When corresponding with your local Sales O󰀩ce about
this equipment, always reference the equipment serial
number stamped on the nameplate.
Parts List
Key Description
1 Base, Carbon steel, 304 Stainless steel
and 316 Stainless steel
2 Cover, Aluminum, Zinc-plated Carbon steel, 304 Stainless steel
and 316 Stainless steel
3 Seal Support, Aluminum, Zinc-plated Carbon steel,
304 Stainless steel and 316 Stainless steel
4 Shield, Aluminum, Zinc-plated Carbon steel, 304 Stainless steel
and 316 Stainless steel
5 Guide, Aluminum, Zinc-plated Carbon steel, 304 Stainless steel
and 316 Stainless steel
6 Seal, Buna-N, Teon®and Viton®
7 Stat-O-Seal, 1/4 in. Fluorocarbon, Stainless steel and Viton®
8 Flat Washer, 1/4 in., 316 Stainless steel
Key Description
When ordering replacement parts, specify the
complete 11-character part number found in Table 1.
9 Fender Washer, 1/4 x 1 in. O.D., 316 Stainless steel
10 Lock Washer, 1/4 in., 316 Stainless steel
11 Hex Bolt, 1/4 in. - 20 x 3 in., 316 Stainless steel
12 Hex Bolt, 1/4 in. - 20 x 2 in., 316 Stainless steel
13 Hex Nut, 1/4 in. - 20, 316 Stainless steel
14 Eyebolt, 1/4 in. - 20 x 3 in., 316 Stainless steel
15 Nylock Hex Nut, 1/4 in. - 20, 316 Stainless steel and Nylon
16 Roller, Zinc-plated Carbon steel, 316 Stainless steel
17 Weight, “Makes”, Zinc-plated Carbon steel
18 Weight, oz./sq. in. or in. w.c., Zinc-plated Carbon steel and
316 Stainless steel
19 Lanyard, Tether or Restraint, 316 Stainless steel
10
2100 Series
North America Only