Emerson Rosemount 3051SAL User manual

Reference Manual
00809-0200-4802, Rev BA
May 2013
Rosemount 3051S Wireless Series
Pressure, Level, and Flow Solutions with IEC 62951
(WirelessHART™) Protocol

i
Reference Manual
00809-0200-4802, Rev BA
Rosemount 3051S Wireless Series
Scalable Pressure, Flow, and Level
Solutions
Read this manual before working with the product. For personal and system safety, and for
optimum product performance, make sure you thoroughly understand the contents before
installing, using, or maintaining this product.
For technical assistance, contacts are listed below:
Customer Central
Technical support, quoting, and order-related questions.
United States - 1 800 999 9307 (7:00 am to 7:00 pm CST)
Asia Pacific- 65 777 8211
Europe/ Middle East/ Africa - 49 (8153) 9390
North American Response Center
Equipment service needs.
1 800 654 7768 (24 hours—includes Canada)
Outside of these areas, contact your local Emerson Process Management representative.
The products described in this document are NOT designed for nuclear-qualified
applications. Using non-nuclear qualified products in applications that require
nuclear-qualified hardware or products may cause inaccurate readings.
For information on Rosemount nuclear-qualified products, contact your local Emerson
Process Management Sales Representative.

ii
Reference Manual
00809-0200-4802, Rev BA
Failure to follow these installation guidelines could result in death or serious injury:
Make sure only qualified personnel perform the installation.
Explosions could result in death or serious injury:
Installation of this transmitter in an explosive environment must be in accordance with the
appropriate local, national, and international standards, codes, and practices. Please review the
approvals section of this manual for any restrictions associated with a safe installation.
Before connecting a 375 Field Communicator in an explosive atmosphere, ensure the
instruments are installed in accordance with intrinsically safe or non-incendive field wiring
practices.
Verify that the operating atmosphere of the transmitter is consistent with the appropriate
hazardous locations certifications.
Process leaks could result in death or serious injury.
Install and tighten process connectors before applying pressure.
Do not attempt to loosen or remove process connectors while the transmitter is in
service.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads can
cause electrical shock.
The Rosemount 3051S and all other wireless devices should be installed only after the
Smart Wireless Gateway has been installed and is functioning properly. Wireless devices
should also be powered up in order of proximity from the Smart Wireless Gateway,
beginning with the closest. This will result in a simpler and faster network installation.
Shipping considerations for wireless products (Lithium Batteries):
The unit was shipped to you without the Power Module installed. Please remove the
Power Module from the unit prior to shipping.
Primary lithium batteries are regulated in transportation by the U. S. Department of
Transportation, and are also covered by IATA (International Air Transport Association),
ICAO (International Civil Aviation Organization), and ARD (European Ground
Transportation of Dangerous Goods). It is the responsibility of the shipper to ensure
compliance with these or any other local requirements. Please consult current
regulations and requirements before shipping.
The power module may be replaced in a hazardous area. The power module has surface
resistivity greater than one gigaohm and must be properly installed in the wireless device
enclosure. Care must be taken during transportation to and from the point of installation
to prevent electrostatic charge build-up.

iii
Reference Manual
00809-0200-4802, Rev BA
Table of Contents
May 2013
Table of Contents
1Section 1: Introduction
1.1 Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .1
1.2 Models Covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2
1.3 Service support. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3
1.4 Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4
2Section 2: Configuration
2.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2 Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5
2.2.1 Warnings (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.3 System readiness . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.3.1 Confirm correct Device Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .6
2.4 Required bench top configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.4.1 Connection diagrams. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7
2.5 Device network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.5.1 Join device to network . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8
2.5.2 Configure update rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.5.3 Remove power module . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
2.6 Review configuration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6.1 Review Pressure Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .10
2.6.2 Review Device and Sensor Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11
2.6.3 Review radio information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.7 Check output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.7.1 Operating parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
2.8 Basic setup. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.8.1 Set process variable unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
2.8.2 Set transfer function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
2.8.3 Damping. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.8.4 Write protect . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
2.9 LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.9.1 LCD display configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
2.10Detailed setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.10.1Configure process alarms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
2.10.2Sensor temperature unit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Table of contents

iv
Reference Manual
00809-0200-4802, Rev BA
Table of Contents
May 2013
Table of Contents
2.10.3Scaled Variable Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
2.10.4Re-Mapping device variables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .22
2.11Diagnostics and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.11.1Master reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23
2.11.2Join status. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2.11.3Number of available neighbors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .24
2.12Advanced functions for HART Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .25
2.12.1Saving, recalling, and cloning configuration data . . . . . . . . . . . . . . . . . . . .25
3Section 3: Installation
3.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
3.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .27
3.2.1 Warnings (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .28
3.3 Considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.3.1 General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.3.2 Wireless . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29
3.3.3 Mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3.3.4 Environmental . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .30
3.4 Installation procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3.4.1 Mount the transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32
3.4.2 Process connections. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38
3.4.3 Consider housing rotation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.4.4 Grounding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.4.5 High gain, remote antenna (optional) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39
3.4.6 Power module installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.4.7 Installing the LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.5 Rosemount 304, 305 and 306 Integral Manifolds . . . . . . . . . . . . . . . . . . . . . . . . . .41
3.5.1 Rosemount 305 Integral Manifold installation procedure . . . . . . . . . . . . .42
3.5.2 Rosemount 306 Integral Manifold installation procedure . . . . . . . . . . . . .42
3.5.3 Rosemount 304 Conventional Manifold installation procedure . . . . . . . .43
3.5.4 Manifold operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .43
4Section 4: Commissioning
4.1 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
4.1.1 Warnings (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47
4.2 Network status . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48
4.3 Verify operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .48

v
Reference Manual
00809-0200-4802, Rev BA
Table of Contents
May 2013
Table of Contents
5Section 5: Operation and Maintenance
5.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
5.2 Calibration. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .51
5.2.1 Sensor trim overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .52
5.2.2 Zero trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
5.2.3 Sensor trim. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .53
5.2.4 Line pressure effect (Range 2 and Range 3). . . . . . . . . . . . . . . . . . . . . . . . . .54
5.2.5 Compensating for line pressure (Range 4 and Range 5) . . . . . . . . . . . . . . .54
5.3 LCD screen messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
5.3.1 Startup screen sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .57
5.3.2 Diagnostic Button Screen Sequence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .59
5.3.3 Network diagnostic status screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60
5.3.4 Device diagnostic screens . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .63
6Section 6: Troubleshooting
6.1 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
6.2 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .67
6.2.1 Warnings (). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68
6.3 Disassembly procedures. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
6.3.1 Remove from service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
6.3.2 Remove terminal block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .72
6.3.3 Removing the feature assembly and the SuperModule from the housing73
6.4 Reassembly procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
6.4.1 Attach the SuperModule to the wireless housing. . . . . . . . . . . . . . . . . . . . .74
6.4.2 Install the Terminal Block . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .74
6.4.3 Reassemble the process flange . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .75
AAppendix A: Specifications and
Reference Data
A.1 Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
A.1.1 Performance specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .77
A.1.2 Functional specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .82
A.1.3 Physical specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .87
A.2 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .92
A.3 Ordering Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
BAppendix B: Product Certifications
B.1 Wireless certifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139

vi
Reference Manual
00809-0200-4802, Rev BA
Table of Contents
May 2013
Table of Contents
B.1.1 Approved manufacturing locations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1.2 Telecommunication compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1.3 FCC and IC approvals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1.4 Ordinary location certification for FM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
B.1.5 Hazardous locations certifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
CAppendix C: High Gain Remote Antenna Option
C.1 Safety messages. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
C.1.1 Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 143
C.2 Functional specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
C.3 Installation considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
C.4 Transient / lightning considerations. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
C.5 Dimensional drawings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 146
C.6 Installation steps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
DAppendix D: Field Communicator Menu Trees and Fast Keys
D.1 Field Communicator menu trees. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 151

Reference Manual
00809-0200-4802, Rev BA
Section 1: Introduction
May 2013
1
Introduction
Section 1 Introduction
Using This Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 1
Models Covered . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 2
Service support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 3
Product Recycling/Disposal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 4
1.1 Using This Manual
The sections in this manual provide information on installing, operating, and maintaining the
Rosemount 3051S Wireless pressure transmitter with IEC 62591 (WirelessHART™) protocol. The
sections are organized as follows:
Section 2: Configuration provides instruction on commissioning and operating 3051S
Wireless transmitters. Information on software functions, configuration parameters,
and online variables is also included.
Section 3: Installation contains mechanical and electrical installation instructions.
Section 4: Commissioning contains techniques for properly commissioning the device.
Section 5: Operation and Maintenance contains operation and maintenance
techniques.
Section 6: Troubleshooting provides troubleshooting techniques for the most common
operating problems.
Section A: Specifications and Reference Data supplies reference and specification data,
as well as ordering information.
Section B: Product Certifications contains approval information.

2
Reference Manual
00809-0200-4802, Rev BA
Section 1: Introduction
May 2013
Introduction
1.2 Models Covered
The following Rosemount 3051S Wireless pressure transmitters are covered in this manual.
Rosemount 3051S Wireless Coplanar™Pressure Transmitter
Rosemount 3051S Wireless In-Line Pressure Transmitter
Rosemount 3051S Wireless Liquid Level Pressure Transmitter
Performance
Class
Measurement Type
Differential Gage Absolute
Classic X X X
Ultra X X X
Ultra for Flow X – –
Performance
Class
Measurement Type
Differential Gage Absolute
Classic – X X
Ultra – X X
Performance
Class
Measurement Type
Differential Gage Absolute
Classic X X X
Ultra X X X

3
Reference Manual
00809-0200-4802, Rev BA
Section 1: Introduction
May 2013
Introduction
1.3 Service support
To expedite the return process outside of the United States, contact the nearest Emerson
Process Management representative.
Within the United States, call the Emerson Process Management Instrument and Valves
Response Center using the 1-800-654-RSMT (7768) toll-free number. This center, available 24
hours a day, will assist you with any needed information or materials.
The center will ask for product model and serial numbers, and will provide a Return Material
Authorization (RMA) number. The center will also ask for the process material to which the
product was last exposed.
The Power Module contains two “C” size primary lithium/thionyl chloride batteries. Each Power
Module contains approximately 2.5 grams of lithium, for a total of 5 grams in each module.
Under normal conditions, the Power Module materials are self-contained and are not reactive as
long as the batteries and the module integrity are maintained. Care should be taken to prevent
thermal, electrical or mechanical damage. Contacts should be protected to prevent premature
discharge. Power Module hazards remain when cells are discharged.
Power Module should be stored in a clean and dry area. For maximum battery life, storage
temperature should not exceed 86 °F (30° C).
Emerson Process Management Instrument and Valves Response Center representatives will
explain the additional information and procedures necessary to return goods exposed to
hazardous substances.
Individuals who handle products exposed to a hazardous substance can avoid injury if they
are informed of and understand the hazard. If the product being returned was exposed to a
hazardous substance as defined by OSHA, a copy of the required Material Safety Data Sheet
(MSDS) for each hazardous substance identified must be included with the returned goods.
NOTICE
Shipping considerations for wireless products (Lithium Batteries):
The unit was shipped to you without the Power Module installed. Please remove the
Power Module from the unit prior to shipping.
Primary lithium batteries (charged or discharged) are regulated in transportation by the
U. S. Department of Transportation, and are also covered by IATA (International Air
Transport Association), ICAO (International Civil Aviation Organization), and ARD
(European Ground Transportation of Dangerous Goods). It is the responsibility of the
shipper to ensure compliance with these or any other local requirements. Please consult
current regulations and requirements before shipping.

4
Reference Manual
00809-0200-4802, Rev BA
Section 1: Introduction
May 2013
Introduction
1.4 Product Recycling/Disposal
Recycling of equipment and packaging should be taken into consideration and disposed of in
accordance with local and national legislation/regulations.

Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
5
Configuration
Section 2 Configuration
Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Safety Messages . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 5
Required bench top configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 7
Device network configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 8
Review configuration data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 10
Check output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Check output . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 12
Basic setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 13
LCD display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 16
Detailed setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 17
Diagnostics and service . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 23
Advanced functions for HART Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . page 25
2.1 Overview
This section contains information on configuration and verification that should be performed
prior to installation.
Field Communicator and AMS instructions are given to perform configuration functions. For
convenience, Field Communicator fast key sequences are labeled “Fast Keys” for each software
function below the appropriate headings.
Example Software Function
2.2 Safety Messages
Procedures and instructions in this section may require special precautions to ensure the safety
of the personnel performing the operations. Information that raises potential safety issues is
indicated by a warning symbol ( ). Refer to the following safety messages before performing
an operation preceded by this symbol.
Fast Keys 1, 2, 3, etc.

6
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
2.2.1 Warnings ( )
2.3 System readiness
If using HART based control or asset management systems, confirm the HART
capability of such systems prior to commissioning and installation. Not all systems are
capable of communicating with HART revision 7 devices.
2.3.1 Confirm correct Device Driver
Verify the latest Device Driver (DD/DTM) is loaded on your systems to ensure proper
communications.
1. Download the latest DD at www.emersonprocess.com.
2. In the Browse by Member dropdown menu, select Rosemount business unit of Emerson
Process Management.
3. Select desired Product
a. Within Table 2-1 on page 7, use the HART Universal Revision and Device Revision
numbers to find the correct Device Driver
Explosions can result in death or serious injury.
Before connecting a 375 Field Communicator in an explosive atmosphere, make sure
the instruments are installed in accordance with intrinsically safe or nonincendive field
wiring practices.
Electrical shock can result in death or serious injury.
Avoid contact with the leads and terminals. High voltage that may be present on leads
can cause electrical shock.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following
conditions: This device may not cause harmful interference this device must accept any
interference received, including interference that may cause undesired operation.
This device must be installed to ensure a minimum antenna separation distance of 20cm
from all persons.

7
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
Table 2-1. Rosemount 3051S Wireless Device Revisions and files
2.4 Required bench top configuration
Bench top configuration requires a 375 Field Communicator, AMS, or any IEC 62591
(WirelessHART) Communicator. Connect the Field Communicator leads to the terminals labeled
“COMM” on the terminal block. See Figure 2-1 on page 8.
Bench top configuration consists of testing the transmitter and verifying transmitter
configuration data. 3051S Wireless transmitters must be configured before installation.
Configuring the transmitter on the bench before installation using a 375 Field Communicator,
AMS, or any IEC 62591 (WirelessHART) Communicator ensures that all network settings are
working correctly.
When using a Field Communicator, any configuration changes made must be sent to the
transmitter by using the “Send” key (F2). AMS configuration changes are implemented when
the “Apply” button is clicked.
AMS Wireless Configurator
AMS is capable of connecting to devices either directly, using a HART modem, or wirelessly via
the Smart Wireless Gateway. When configuring the device, double click the device icon or right
click and select Configure.
2.4.1 Connection diagrams
Bench hook-up
Connect the bench equipment as shown in Figure 2-1 on page 8, and turn on the Field
Communicator by pressing the ON/OFF key or log into AMS. The Field Communicator or AMS
will search for a HART-compatible device and indicate when the connection is made. If the Field
Communicator or AMS fail to connect, it indicates that no device was found. If this occurs, refer
to Section 6: Troubleshooting.
Identify Device Find Device Driver
Review
Instructions
Review
Functionality
Software
Release Date
NAMUR
Software
Revision(1)
(1)
(1) NAMUR Software Revision is located on the hardware tag of the device.
HART
Software
Revision(2)
(2) HART Software Revision can be read using a HART capable configuration tool.
HART
Universal
Revision
Device
Revision(3)
(3) Device Driver file names use Device and DD Revision, e.g. 10_01. HART Protocol is designed to enable legacy device driver revisions to continue to
communicate with new HART devices. To access new functionality, the new Device Driver must be downloaded. It is recommended to download new
Device Driver files to ensure full functionality.
Manual
Document
Number
Changes to
Software
April 2013 3.1.0 3 7 3 00809-0200-4802
Rev BA
Added Scaled
Variable
June 2010 2.0.0 2 7 2 00809-0200-4802
Rev AA
N/A

8
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
Field Hook-up
Figure 2-1 illustrates the wiring for a field hook-up with a Field Communicator or AMS. The Field
Communicator or AMS may be connected at “COMM” on the transmitter terminal block.
Figure 2-1. Field Communicator Connection
For HART communication, a 3051S WirelessHART DD is required.
2.5 Device network configuration
2.5.1 Join device to network
In order to communicate with the Smart Wireless Gateway, and ultimately the Host System, the
transmitter must be configured to communicate over the wireless network. This step is the
wireless equivalent of connecting wires from a transmitter to the host system.
1. From the Home screen, choose 2: Configure.
2. Choose 1: Guided Setup.
3. Choose 3: Join Device to Network.
Using a Field Communicator or AMS, enter the Network ID and Join Key so that they match the
Network ID and Join Key of the Smart Wireless Gateway and other devices in the network. If the
Network ID and Join Key are not identical to those set in the Gateway, the transmitter will not
communicate with the network. The Network ID and Join Key may be obtained from the Smart
Wireless Gateway on the Setup>Network>Settings page on the web server.
Fast Keys 2, 1, 3
COMM
P/N 00753-9200-0010
COMM
COMM
P/N00753-9200-0010
P/N00753-9200-0010

9
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
2.5.2 Configure update rate
The Update Rate is the frequency at which a new measurement is taken and transmitted over
the wireless network. This by default is 1 minute. This may be changed at commissioning, or at
any time via AMS Wireless Configurator. The Update Rate is user selectable from 1 seconds to 60
minutes.
1. From the Home screen, choose 2: Configure.
2. Choose 1: Guided Setup.
3. Choose 4: Configure Update Rate.
When device configuration is completed, remove the Power Module and replace the housing
cover. Tighten the cover so that metal contacts metal.
2.5.3 Remove power module
After the sensor and network have been configured, remove the Power Module and replace the
housing cover. The Power Module should be inserted only when the device is ready to be
commissioned.
Use caution when handling the power module. It may be damaged if dropped onto a hard
surface. Battery hazards remain when cells are discharged.
This transmitter uses the Black Power Module. Please order model number 701PBKKF or spare
part number 00753-9200-0001.
Fast Keys 2, 1, 4

10
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
2.6 Review configuration data
The following is a list of factory default configurations that can be viewed by using the Field
Communicator or AMS. Follow the steps below to review the transmitter configuration
information.
Note
Information and procedures in this section that make use of Field Communicator fast key
sequences and AMS assume that the transmitter and communication equipment are
connected, powered, and operating correctly.
2.6.1 Review Pressure Information
To view pressure information:
1. From the Home screen, choose 2: Configure.
2. Choose 2: Manual Setup.
3. Choose 2: Pressure.
4. Choose from the corresponding number to view each field:
Fast Keys 2, 2, 2
1Pressure
2Pressure Status
3Units
4Damping
5Sensor Limits

11
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
2.6.2 Review Device and Sensor Information
To view device information:
1. From the Home screen, choose 2: Configure.
2. Choose 2: Manual Setup.
3. Choose 9: Device Information.
4. Choose from the corresponding number to view each field:
Fast Keys 2, 2, 9
1Identification
2Revisions
3Radio
4Sensor information
5Flange information
6Remote seal information

12
Reference Manual
00809-0200-4802, Rev BA
Section 2: Configuration
May 2013
Configuration
2.6.3 Review radio information
To view radio information:
1. From the Home screen, choose 2: Configure.
2. Choose 2: Manual Setup.
3. Choose 9: Device Information.
4. Choose 3: Radio.
5. Select from the corresponding number to view each field:
2.7 Check output
Before performing other transmitter operations, ensure that the transmitter is operating
properly by checking the operating parameters.
2.7.1 Operating parameters
The pressure output value in both engineering units and percent of range will reflect the applied
pressure even when the applied pressure is outside of the configured range as long as the
applied pressure is between the upper and lower range limit of the transmitter. For example, if a
Range 2 3051S_T (LRL = 0 psi, URL = 150 psi) is ranged from 0 to 100 psi, an applied pressure of
150 psi will return a % of range output of 150% and an engineering output of 150 psi.
To view the Operating Parameters menu:
1. From the Home screen, select 3: Service Tools.
2. Choose 2: Variables.
Fast Keys 2, 2, 9, 3
1Manufacturer
2Device Type
3Device Revision
4Software Revision
5Hardware Revision
Fast Keys 3, 2