Eminent EM6220 User manual

EM
6220
e-CamView Pan/Tilt IP camera

2 | ENGLISH
EM6220 – e-CamView Pan/Tilt IP camera
Table of contents
1.0 Introduction ...........................................................................................................3
1.1 Packing contents...............................................................................................3
1.2 Requirements to access the camera..................................................................3
1.3 Major hardware components. ............................................................................3
2.0 Installing the camera .............................................................................................5
2.1 Connecting the camera to your network using a network cable..........................5
2.2 Installing the e-CamView App on an Apple/Android device................................6
2.3 Installing the software and camera on a PC or notebook (Windows)..................6
2.4 Adding the camera to a wireless network...........................................................7
2.4.1 Connecting to Wi-Fi using the App.............................................................. 7
2.4.2 Connecting to Wi-Fi using the PC utility (windows). .................................... 8
2.5 Mounting the camera on the wall.......................................................................8
3.0 Viewing images.....................................................................................................8
3.1 On your smartphone/tablet (Android, iPhone, iPad)...........................................9
3.2 On your PC (Windows) in a remote location. .....................................................9
4.0 e-CamView for iPhone/iPad/Android......................................................................9
4.1 The Layout of e-CamView.................................................................................9
4.2 WIFI setting.....................................................................................................10
4.3 User setting.....................................................................................................11
4.4 Time setting.....................................................................................................12
4.5 Alarm setting ...................................................................................................12
4.6 FTP setting......................................................................................................13
4.7 Mail setting......................................................................................................13
4.8 SD-card setting................................................................................................14
5.0 e-Cam-View for PC software ...............................................................................14
5.1 The layout of e-CamView ................................................................................14
5.2 Recording settings...........................................................................................15
5.3 Base info.........................................................................................................15
5.4 Time setting.....................................................................................................16
5.5 Network...........................................................................................................17
5.6 SD record scheme...........................................................................................17
5.7 User and password..........................................................................................17
5.8 Email setting....................................................................................................18
5.9 FTP setting......................................................................................................18
5.10 PTZ...............................................................................................................19
5.11 Alarm setting .................................................................................................19
5.12 WIFI setting...................................................................................................20
6.0 The webpage of the camera................................................................................20
6.1 Login by Web browser.....................................................................................20
6.2 The layout of e-CamView ................................................................................22
6.3 Multi device settings........................................................................................23

3 | ENGLISH
6.4 FTP setting......................................................................................................23
6.5 Alarm log.........................................................................................................24
6.6 Maintenance....................................................................................................24
7.0 Restore factory settings.......................................................................................24
8.0 Upgrade Device Firmware..................................................................................25
9.0 Frequently Asked Questions and other related information..................................25
10.0 Service and support...........................................................................................25
11.0 Warning and points of attention .........................................................................26
12.0 Warranty conditions...........................................................................................27
1.0 Introduction
Congratulations with the purchase of this high-quality Eminent product! This product
has undergone extensive testing by Eminent’s technical experts. Should you
experience any problems with this product, you are covered by a five-year Eminent
warranty. Please keep this manual and the receipt in a safe place.
Register your product now on www.eminent-online.com and receive product updates!
1.1 Packing contents
The following parts need to be present in the packing:
•EM6220
•Power supply
•Quick install guide
•Network cable
•Mounting bracket with screws and plugs
•CD-ROM with software and wizard
1.2 Requirements to access the camera.
It is very easy to access the video images of the EM6220 on your smartphone, tablet
or PC. You only need the ID or QR code that is displayed on your bottom label and
download the application for your device. You do not need to remember or setup the
configuration of your modem/router to be able to access the camera.
1.3 Major hardware components.
The major components on the front panel of the EM6220 are the built-in microphone,
lens and IR LED’s :

4 | ENGLISH
1. Microphone – for receiving the audio/voice.
2. Lens – the lens is inside the camera body and the focus of the lens is fixed, you
do not need to spend time to adjust the focus.
3. IR LED – for the Infra-Red lighting of the night mode usage.
4. Day/Night sensor – sensor for day/night detection
The major components on the back panel of the EM6220 are the power jack, Ethernet
jack and Speaker jack:
1. Speaker jack – connect to an external speaker for two way audio.
2. Power jack – this is the place to plug in the power adapter. The power needed for
this EM6220 is 5V/2A, please make sure you are using the correct power adapter.
3. Ethernet jack – this is the place to plug in the RJ45 Ethernet cable.
4. Antenna jack – this is the place to mount the WiFi antenna
5. Internal Speaker

5 | ENGLISH
The major components on the bottom of the EM6220 are the bracket screw jack and
reset button:
1. Reset button – this is the button to reset the EM6220 to default factory settings.
You need to use a small stick like pencil or tooth stick to press the reset button for
more than 15 seconds to enable the reset function. Please refer to section 7.0 for
more details.
2. Bracket screw jack – this is the position to screw in the bracket of the EM6220.
With the bracket, you can install the EM6220 on the wall.
2.0 Installing the camera
A few short and simple steps are necessary to connect and assign the camera, and to
enjoy the use of the camera. Use the following steps to connect the camera.
2.1 Connecting the camera to your network using a
network cable
We advise to connect the camera first with a network cable. Once the camera works
correctly, you can use your wireless network.
1. Connect the camera to a power outlet using the supplied power adapter.
2. Connect the camera to your router or switch using the supplied network cable.

6 | ENGLISH
2.2 Installing the e-CamView App on an Apple/Android
device
Before you can view the video of the camera, you need to download and install the
app “e-CamView” from the “Play Store” or “App Store”.
1. Download and install the app “e-CamView” from the “Play Store” or “App Store”.
2. Open e-CamView.
3. Select the “+” button to add the camera to the App.
4. A new window opens to enter the data of the camera.
5. Here you can choose to install the camera: Manually, Scan QR code or LAN
Search.
6. Now enter the device ID manually, Scan the QR code on the bottom label or
select the camera you just found in the LAN search.
Password: This is the 4 digit password you can find on the bottom label of the
camera.
7. Select “Done” to add the camera.
2.3 Installing the software and camera on a PC or
notebook (Windows).
Before you can view the video of the camera, you need to install the software” e-
CamView” from the CD-ROM.
1. Insert the CD in the CD-ROM.
2. If auto-run is enabled the Wizard should start.
3. Run the wizard to install the application e-CamView.
4. The application is installed on the PC
5. Open e-CamView. (If prompted with a screen about the firewall click always

7 | ENGLISH
allow).
6. Click “Device list” to add the camera
7. If the computer and the EM6220 is connected to the same network, the Camera
can be added by clicking “open search tool”.
8. Click “search”
9. The devices are displayed with the Device ID in the search list. You add the
Camera to the device list by double clicking the device.
10. A new window will be displayed here you can change the name of the camera and
enter the password of the camera that is printed on the bottom label.
11. If the EM6220 is not in the same network as the computer you can add the
EM6220 by clicking “Device list” followed by “Add” enter the username “admin”
and the “Device ID” in the UID field and enter the password (you can find this
information on the bottom label of the camera) press “OK”.
2.4 Adding the camera to a wireless network
There are 2 options to connect the EM6220 to your wireless network. First option is to
configure the settings by using the App. The second option is to use the software
installed on your PC (windows).
Note: The device will reboot if necessary you will hear a buzzing sound from the
speaker of the camera followed by calibration of the camera.
2.4.1 Connecting to Wi-Fi using the App.
1. Ensure the camera is connected to the network with a Ethernet cable.
2. Start the App “e-CamView”.
3. Select the “Camera settings” menu by pressing the arrow next to the camera you
would like to configure.
(if prompted Login with username: (default “admin”)
Password: (default “leave blank”)
4. Select “Wi-Fi setting”
5. A list of available wireless networks will be displayed.
6. Select the wireless network you want to connect to (if not displayed press “ ”)
7. Enter the wireless encryption key and press “Done”
8. Disconnect the Ethernet cable to connect to the wireless network.

8 | ENGLISH
2.4.2 Connecting to Wi-Fi using the PC utility (windows).
1. Ensure the camera is connected to the network with a Ethernet cable.
2. Ensure the camera is added to the device list (see chapter 2.3)
3. Double click the camera in the camera list
4. The settings menu will be displayed
5. Go to the Menu option “WiFi”
6. If necessary enable the WiFi option by enabling the selection box “WiFi in use”
7. Click “Wi-Fi scan” to search for available wireless networks, please press refresh if
your wireless network is not displayed (If device is just rebooted please be patient
for the device to be ready to refresh the WIFI list).
8. Select the Wireless network you want to connect to.
9. Enter the Encryption settings and the WPA-PSK key of the wireless network
10. Click “Set”.
2.5 Mounting the camera on the wall
1. Once the camera is connected correctly with your computer, you can mount the
camera on a wall or ceiling.
2. Use the mounting stand to mark the holes at the location where you want to mount
the camera.
3. Drill the holes and fill the holes with the supplied plugs.
4. Mount the bracket stand to the wall or ceiling using the supplied screws. If the
bracket is still attached to the camera, you can twist of the bracket again, in order
to make mounting the screws easier.
5. Mount the camera on the bracket.
6. Connect the power supply into the wall socket and connect the power tip to the
camera.
3.0 Viewing images
You can view the images both on your computer and on your smartphone screen, as
we explain in the sections below.
Optionally, you can install the supplied software so you can find the camera directly
with your computer and make recordings with your computer.

9 | ENGLISH
3.1 On your smartphone/tablet (Android, iPhone, iPad)
Start the App e-CamView press the camera-icon of the camera you wish to view. The
device will start connecting with the camera and will show live images of the camera.
3.2 On your PC (Windows) in a remote location.
After e-CamView software is installed, it’s very easy to add a camera item in the
“Camera List” folder of the e-CamView software, key in the CAM ID (from the bottom
label). And then drag and drop the camera in the screen you wish to view the camera
stream in. You will then see the Camera video immediately. No further NAT/router
setting modifications are needed. The camera can be controlled remotely as well.
4.0 e-CamView for iPhone/iPad/Android
4.1 The Layout of e-CamView
Edit Camera
Add Camera
View Camera Camera settings
View snapshots View Recordings
App information

10 | ENGLISH
4.2 WIFI setting
You can select if the camera will use a WiFi connection and what AP or Router it will
connect to. Also you can set the encryption settings of the WiFi connection you wish to
connect to.
Hor. & vert. Patrol Mirror/Flip image
Exit live stream
Take Snapshot
Start recording
Enable / disable
Speaker /
Microphone
Adjust Contrast
and Brightness
Default Video
settings
Change aspect
ratio
Change video
resolution