EMP-Centauri S16/4PCN-W3 User manual

Instruction Manual 1003957-EN A
S16/4PCN-W3
Dear Customer,
congratulations on the purchase of the EM -Centauri product. Before its
installation and putting into operation, read carefully the entire operation manual.
Keep the purchase and rework (if any) records for future need.
1) Field of Application, Warranty
The product is designed for the distribution of satellite TV and radio signals.
EM -Centauri΄s ROFI CLASS products are covered under 6 (six) years warranty
from the date of purchase. The warranty shall not apply to the product used for
other than the specified purpose. The user will be responsible for injury or material
damage which may arise in consequence of any product use in contradiction with
the manual.
Repairs or any interventions in the product may be performed only by EM -
Centauri company, or other companies authorized by EM -Centauri.
2) Technical Specifications
S16/4 CN-W3 is a DiSEqC-Multiswitch in the weatherproof housing for
distribution of satellite signals from 4 Quad LNBs to 4 users. It is controlled by
DiSEqC 1.0 / 2.0 commands from a receiver. The multiswitch transmits DC
voltage, 22 kHz and DiSEqC commands. The inputs are short-circuit protected.
Specifications S16/4 CN-W3
Inputs / Outputs 16 / 4
Frequency Range 950–2300 MHz
Insertion Loss (avg)* 4 dB
Isolation (min) 25 dB
Current Consumption 35 mA (18V) from satellite receiver
LNB current (max) 400 mA
Dimensions (w,d,h) 17.2 x 20.0 x 6.9 cm
Temperature Range −30°C – +70°C
*avg - average value, there is tolerance of ±3 dB in specified range
1 of 4

3) roduct Takeover
Make sure that the product is not damaged. lease contact your dealer in the
case of damage.
4) roduct Storing and Installation
We recommend the device to be installed and serviced by the qualified
technician.
The product must not be stored and installed in the place with excessive dust
pollution, mechanical vibrations or impacts in the place out of temperature limits
specified in the section 2) Technical Specifications close to heat sources
(radiators or air ventilators, etc.) and in the reach of children. Fix the product firmly
on a wall or another hard and inflammable surface with screws and dowels or fix it
to the antenna mast with folding strip, the direction of F sockets is always
downward. The product shall be in no case held only by the connected cables. Do
not place any containers with liquids (vases, glasses etc.) or naked flame sources
(lighted candle etc.) on the product or near the product.
5) roduct Connection
Connect the product in accordance with this manual and valid regulation. Use
high-quality 75 Ω coaxial cable designed for satellite reception. Mount the F
connectors (screw, crimp or compress type) on the ends of coaxial cables.
Connect the F connectors into the F sockets of product and fasten them with an
appropriate force. The coaxial cables shall not be broken, the minimum bending
radius should be 5 cm.
•Connect input F sockets marked „SAT 1 IN“, „SAT 2 IN“,„SAT 3 IN“,
„SAT 4 IN“, with outputs of Quad LNBs
•Connect output F sockets marked „OUT“ with other components in
distribution system (satellite receivers, wall sockets etc.).
The wiring examples are shown in the section 10) Wiring Diagrams or at
www.emp-centauri.eu.
6) roduct Settings
Satellite receiver must be set according to following table:
2 of 4

LNB (SAT) Variant 1 Variant 2 Variant 3
1 DiSEqC 1.0: 1 of 4 DiSEqC 1.0: A AA
2 DiSEqC 1.0: 2 of 4 DiSEqC 1.0: B AB
3 DiSEqC 1.0: 3 of 4 DiSEqC 1.0: C BA
4 DiSEqC 1.0: 4 of 4 DiSEqC 1.0: D BB
7) Safety
Due to security reasons the product and wiring in which the product is connected,
must be grounded properly. Make sure the antennas are grounded properly.
Connect all devices to power grid only after all connections are finished and
checked. Never work on the wiring (including satellite receivers, TVs) during or
before a storm. A lightning stroke into the antenna may cause dangerous
overvoltage in the product metallic parts.
8) roduct Maintenance
Always disconnect the product from the wiring before performing any
maintenance of the product. If you have to enter places with a risk of fall, pay
attention to your safety. Use only dry cloth to clean the product and do not use any
liquid agents. Coaxial cables installed outdoors should be replaced once in a few
years. Unscrew all F connectors and clean connector contacts, resp. shorten the
coaxial cable by approx. 2 cm, every 2 years.
9) Symbols Explanation
certificate of conformity
international standard for digital satellite equipment control, number
(1.0, 1.1, 1.2 or 2.0) determines DiSEqC version
According to EU directive, electric and electronic devices which are
identified by one of the following symbols must not be disposed of
together with municipal waste. When disposing of the old device, use
local waste collection and separation systems.
3 of 4

11) Contact
Manufacturer: EM -Centauri s.r.o.
5. kvetna 690
339 01 Klatovy
Czech Republic
tel: [phone]
fax: [phone]
[email protected]
www.emp-centauri.cz
10) Wiring Diagram
4 of 4
S16/4 CN-W3
4x QUAD LNB4x QUAD LNB