EMP-Centauri T1/1+1ENP8dB-1 User manual

Instruction Manual
T1/1+1ENP8dB-1
T1/1+1ENP12dB-1
T1/1+1ENP16dB-1
T1/1+1ENP20dB-1
Dear Customer,
congratulations on the purchase of the EMP-Centauri product. Before its
installation and putting into operation, read carefully the entire operation manual.
Keep the purchase and rework if any) records for future need.
1) Field of Application, Warranty
The product is designed for the distribution of terrestrial including cable) TV and
radio signals.
The manufacturer provides for E.LITE CLASS products extended 4 four) years
warranty from the date of purchase, see details in EMP-Centauri’s General trade
conditions, published at manufacturer’s website www.emp-centauri.cz.
It is prohibited to dismantle the product and make any interventions in it. Repairs
or any interventions in the product may be performed only by EMP-Centauri
company, or other companies authorized by EMP-Centauri.
2) Technical Specifications
The product is wideband passive tap that can be used for distributing signals in
terrestrial and/or satellite frequency bands. Level balancing of whole system can
be achieved by using different tap loss versions. We therefore offer this product
with tap loss stepped from 9 to 20 dB part types T1/1+1ENP8dB-1,
T1/1+1ENP12dB-1, T1/1+1ENP16dB-1, T1/1+1ENP20dB-1).
Trunk path transmits DC voltage, 22 kHz and DiSEqC commands. Terrestrial port
is DC isolated.
Specification for T1/1+1ENP… … dB-1 …12dB-1 …16dB-1 …20dB-1
Inputs / Outputs 1 / 2 trunk + tap)
Frequency Range 5–2150 MHz
Tap loss max) 9 dB 12 dB 16 dB 20 dB
Trunk loss max) 2.5 dB
Dimensions w,d,h) 5.4 x 6.0 x 3.2 cm
Temperature Range −25 °C – +60 °C
1 of 4

3) Product Takeover
Make sure that the product is not damaged. In the case of damage please contact
your dealer.
4) Product Storing and Installation
We recommend the device to be installed and serviced by the qualified
technician.
The product must not be stored and installed:
•in the place with excessive humidity
•in the place with dropping or splashing water,
•in the place with excessive dust pollution, mechanical vibrations or
impacts
•in the place out of temperature limits specified in the section 2)
Technical Specifications
•close to heat sources radiators or air ventilators, direct sunshine etc.)
•in the reach of children
Use the apparatus only in moderate climates not in tropical climate).
Fix the product firmly on a wall or another hard and inflammable surface with
screws and dowels. The product shall be in no case held only by the connected
cables.
Further instructions:
•ensure the free space at least 10 cm around the product for the
sufficient air circulation
•do not cover the product with curtains etc.)
•do not place any containers with liquids vases, glasses etc.) or naked
flame sources lighted candle etc.) on the product or near the product
2 of 4

5) Product Connection
Connect the product in accordance with this manual and valid regulation in you
country. Use high quality 75 Ω coaxial cable designed for satellite reception. The
coaxial cables shall not be broken, the minimum bending radius should be 5 cm.
Mount the F connectors screw, crimp or compress type) on the ends of coaxial
cables. Connect the F connectors into the F sockets of product and fasten them
with an appropriate force.
•Connect F-socket “TRUNK1+DC” to preceding device in cascade /
distribution system
•Connect F-socket “TRUNK2+DC” to following device in cascade /
distribution system
•Connect F-socket “TAP DC blocked)” to next wide-band device /
receiver
6) Product Settings
The product has no adjustable options.
7) Safety
Due to security reasons the product and wiring in which the product is connected,
must be grounded properly. Make sure the antennas are grounded properly.
Connect all devices to power grid only after all connections are finished and
checked. If you have to enter places with a risk of fall, pay attention to your safety.
Never work on the wiring including terrestrial receivers, TVs) during or before a
storm. A lightning stroke into the antenna may cause dangerous overvoltage in the
product metallic parts.
The product should be disconnected from the wiring immediately if it gets into
contact with liquids dropping water, spilled drinks etc.).
) Product Maintenance
The maintenance operation is especially cleansing of the product. Use only dry
cloth to clean the product and do not use any liquid agents.
Coaxial cables installed outdoors should be replaced once in a few years.
Unscrew all F connectors and clean connector contacts, resp. shorten the coaxial
cable by approx. 2 cm, every 2 years.
3 of 4

10) Contact
Manufacturer: EMP-Centauri s.r.o.
5. kvetna 690
339 01 Klatovy 4
Czech Republic
tel: [phone] sales)
tel: [phone] tech. support)
[email protected]
www.emp-centauri.cz
9) Symbols Explanation
Certificate of conformity
According to EU directive, electric and electronic devices which are
identified by one of the following symbols must not be disposed of
together with municipal waste. When disposing of the old device, use
local waste collection and separation systems.
4 of 4