Wrist Talker
Easy to wear!
This single message communicator is easy to use.
•Record message of up to 10 seconds
•Great sound quality
•Enables the user to communicate any greeting
•Easy to record and re-record
•Has an adjustable strap
Size: 2¼"D x 1½"H. Requires 3 LR44
Button Cells (Included . Weight: ¼ lb.
Operation:
Operation:Operation:
Operation:
1. Wrist Talker requires 3 LR44 Button cell batteries to operate
(Included . Please Note:
Please Note:Please Note:
Please Note: Before use remove and discard the round
Before use remove and discard the round Before use remove and discard the round
Before use remove and discard the round
foam
foam foam
foam disk
diskdisk
disk
with hole in the center. This was used to prevent
with hole in the center. This was used to prevent with hole in the center. This was used to prevent
with hole in the center. This was used to prevent
battery dr
battery drbattery dr
battery draining during shipping.
aining during shipping.aining during shipping.
aining during shipping.
To Record:
To Record:To Record:
To Record:
2. To make a recording simply twist the cover until the opening lines up
with the gray rubber record button (see illustrations . Next depress
the record button and speak your message from six to eight inches
away from it. When finished recording release the record button. You
have a maximum record time of ten seconds.
To Replace Batteries:
To Replace Batteries:To Replace Batteries:
To Replace Batteries:
3. Turn the Wrist Talker over, and then carefully remove the black Velcro
wrist strap (see illustrations . Next with one hand turn the unit back
over, catch the white disk and voice module in your other hand as it
drops out. There are three tabs on the voice module that need to be
depressed in order to replace the batteries. Hold the voice module
with the speaker side facing down. Next with your thumb nail press in
and lift gently on the three tabs on the sides of the cove one at a
time.
4. Please Note:
Please Note:Please Note:
Please Note: On the body of the voice module you will see three
groves, just above them are the tabs you need to depress (see
illustrations . Once this is done the cover should lift off. Observing
proper (+ and (- battery polarity, install three LR44 button cell
batteries into the holders (+ side facing up . Replace the speaker and
circuit board, making note to line up the grove in the speaker and
circuit board with the grove in the white casing (see illustrations . If
this is not done the unit will not go back together properly.
Message Playback:
Message Playback:Message Playback:
Message Playback:
4. To play back your message slid the cover plate back so that the
microphone is showing through the opening in the cover. Next
depress the center white button.
5. When placing the recording modal back into the wrist holder face the
speaker side towards you. Next place the round disc in place and
feed the wrist strap through both slots. When the wrist talker is on
your wrist the speaker should be facing down towards your wrist and
the message play-back button should be facing up on top.
Troubleshooting:
Troubleshooting:Troubleshooting:
Troubleshooting:
Problem:
Problem:Problem:
Problem: The unit fails to operate, or operates incorrectly.
Action #1:
Action #1:Action #1:
Action #1: Make sure that you have assembled all the parts correctly
according to the instructions and illustration sheet.
Action #2:
Action #2:Action #2:
Action #2: Check your batteries – There is a 99% chance that either one
is installed incorrectly and/or one is weak/dead.
Action #3:
Action #3:Action #3:
Action #3: Disconnect the power by removing one of the batteries for 20
seconds in order to reset the unit. Re-install the batteries. If the unit
does not work correctly, replace all the batteries paying careful attention
to proper polarity.
Care of the Unit:
Care of the Unit:Care of the Unit:
Care of the Unit:
The Wrist Talker can be wiped clean with any household multi-purpose,
non-abrasive cleaner and disinfectant.
Do not use
Do not useDo not use
Do not use abrasive cleaners, as they will scratch the surface of the unit.
Do not submerge
Do not submergeDo not submerge
Do not submerge the unit, as it will damage the electrical components.
Rev
Rev Rev
Rev 4
44
4/27
/27/27
/27/17
/17/17
/17
