ENACFIRE H500 User manual

(| enacEIRe
TRUE WIRELESS
STEREO EARPHONES
ENACFIRE H500 INSTRUCTION

Contents
® English 01-14
® Deutsch 15-27
© Espaiiol 28-40

Customer Support ——————————— 1
[email protected] (US/CA)
[email protected] (UK)
We will reply to you within 24 hours and 100% solve your issues
Packaging List
) ()
0
=
5 \/
Earphones x1 Charging Case x1
06 s
66 v
OO
Eartips x6 USB Type-C Manual x1 Warranty Card x1
Charging Cable x1

Product Over:
1. Charging Case LED Light
2. Charging Port
3 Multifunctional Button
4. Earphone Mic
5. Magnetic Charging Pin
6. Earphone LED Light

Power On & Pairing
Approach 1-With Charging Case
1. Take out earphones from the
charging case
2. Select ENACFIRE H500' from
Bluetooth list
G
EnachRE W00

Approach 2 - Without Charging Case
1. Power On: Touch the earphones for 1 second. Release when you
hear the prompt sound ‘Power on’ with Blue light on.
2. Pairing: Earphones will pair automatically with Left earphone
Blue and White light flash alternately
3. Select 'ENACFIRE H500' from the device's Bluetooth list

Incoming call
Answer call/End call
Tap the Left / Right earphone once
.u V : Tap el G“(%
s TR
Reject call
Touch the Left / Right earphone for 2 seconds.
&
Touch for 2588 1=

Music
Pause/Play
| |
Tap the Left/ Right earphone once to
pause / play music in the music mode
(Some phones may require to start
amedia player first)
Voice Assistant @
Tap the Left/ Right earphone 3 y
times, your device's Voice
Assistant will be activated with
the 'Beep’ prompt sound »

Next Song
Double-tap the Right earphone
Previous Song
Double-tap the Left earphone
Adjust Volume
Touch and hold the Left earphone to decrease volume
Touch and hold the Right earphone to increase volume
Note:
Above functions are not supported when the earphone is used i
single. Prompt sound ‘Beep’ will be produced when the volume s
changing.

PowerOff
—
8
Mode 1
With Charging Case
Put the earphones back to the charging case, they will power off
automatically.
Note: Put either one earphone into the charging case, the another
earphone wil stay connect to the device.
Mode 2
Without Charging Case
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both
earphones '
Touch 85l

Single Mode
single
Mode Earphone
With Charging | 1+ 194€ 0ut Lot Right crphone from the charging case
c
ase 2. Select ENACFIRE H500' from Bluetooth list
1. Make sure both earphones are turn off
2. Touch the Left Right earphone for 1 second to
Without
Charging Case | 14 O Prompi sound Paring wil be produced
with Blue and White ligh flash alternately.
3. Select ENACFIRE HS00'from Bluetooth lst

Charging
10
Earphones
Charging
Status
Earphones white LED light on: Charging
Earphones white LED light off: Fully charged
Note: It takes about 1.5 hours to fully charge the earphones.
Charging Case Charging Status
Put the earphones back to the charging case
Lights on charging case stand for the remaining battery capacity
Note: It takes about 1.5-2 hours to fully charge the charging case
173 Battery Left
23 Battery Left
Fully charged

Safety Instruction "
Using earphones at high to moderate volumes for extended periods.
of time will result in permanent hearing damage. It is advised that
you keep volume levels moderate to low at all times for your safety.
Do not use while driving, cycling, operating machinery or performing
other activities that require hearing surrounding sounds.
Do ot use earphones in thunderstorm weather, the earphones may
notwork properly in the bad weather condition, and may increase
the risk of being hit by lightning.
Earphones may not work properly under high temperature or high
humidity conditions,
Do not use any corrosive cleaner/oil to clean the earphones . If the
earphones come in contact with liquids, quickly wipe away. If
submersed in the water, do not turn the earphones on untilt is
completely dried.
Tips: Man-made damage and lost are not covered under warranty.
Keep the earphones and the packaging out of reach of children.

Q&A
12
Q: Why the music cuts in and out sometimes?
A: Please make sure there is no obstacle between the earphones and
your device. Please make sure there is no Microwave oven / Wifi
transmitter around you, which are more likely to produce
electromagnetic interference and result n signal interruption.
Note: Please keep your phone and the earphone as close as possible
to ensure a more stable Bluetooth connection.
Q: What should | do if the earphones stop charging?
A We recommend you to charge the earphones by using our cable
If our cable do not work, please try to use another charging cable or
power source to charge the earphones.
Q: How to contact ENACFIRE Customer Service Team?
A:If you have any issue with the product, please contact us via
[email protected] (US/ CA) / [email protected]
(UK). We wil reply to you within 24 hours and 100% solve your issue.

FCCStatement
This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules,
‘These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur ina
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the.
following measures;
—Reorient o relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2)this device must accept any interference received, including
interference that may cause undesired operation
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.