ENACFIRE F2 User manual

(| enacziRe
TRUE WIRELESS
STEREO EARPHONES
NACFIRE F2 INSTRUCTION

Contents
® English 01-14
@® Deutsch 15-27
© Espaiol 28-40

Customer Support ———————————— 1
[email protected] (US/CA)
[email protected] (UK)
We will reply to you within 24 hours and 100% solve your issues
Packaging List
fi?
Earphones x1 Charging Case x1
006 s @
o6 M
006
Eartips x 3 Manual x1 Warranty Card x1 UsB
Charging Cable x1

Product Overview
1. Charging Case LED Light
2. Charging Port °
3. Multifunctional Button 0
4. Earphone Mic
5. Magnetic Charging Pin
6. Earphone LED Light

Power On & Pairing
Approach 1-With Charging Case
1. Open the charging case cap
2. Select ENACFIRE F2 from Bluetoothlist

Approach 2 - Without Charging Case
1. Power On: Touch the earphones for 1 second. Release when you
hear the prompt sound ‘Power on’ with White light on.
R Touch 1588
2. Pairing: Earphones will pair automatically with Red and White
light flash alternately
3. Select ENACFIRE F2' from the device's Bluetooth list

Incoming call
Answer call/End call
Tap the Left / Right earphone once
LR
Reject call
Touch the Left/ Right earphone for 2 seconds
Touch for 2488
LR

Music
Pause/Play
Tap the Left/ Right earphone once to
pause / play music inthe music mode P /I
(some phanes may require to start
amedia player first)
Voice Assistant @
Tap the Left/ Right earphone 3
times, your device's Voice
Assistant will be activated with
the ‘Beep’ prompt sound
UR

Next Song
®
Double-tap the Right earphone »
Previous Song
Double-tap the Left earphone. « ©
Adjust Volume
Touch and hold the Left earphone to decrease volume
Touch and hold the Right earphone to increase volume
Note:
Above functions are not supported when the earphone is used in
single. Prompt sound ‘Beep’ will be produced when the volume reach
minimum or maximum level.

Power Off
Mode 1
With Charging Case
Put the earphones back to the charging case and close the cap, they
will power off automatically.
Note: Put either one earphone into the charging case, the another
earphone will stay connected to the device.
Mode 2
Without Charging Case
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both
(]
C
R
earphones

Single Mode
single
Earphone
Mode ?
With Charging | 1124 0Ut Lot Rght earphane rom the chargingcase
case 2. Select ENACFIRE F2' from Blustooth list
1. Make sure both earphones are turn off
2.Touch the Left/ Right earphone for 1 second to
Without
r turn on. Prompt sound Pairing wilbe produced
Charging Case
with Red and White ight flash alternately.
3. Select ‘ENACFIRE F2' from Bluetooth list

Charging
10
Earphones Charging Status
Open and close the charging case cap, wait for 5 seconds
Leftmost charging case LED light flashing: Left earphone charging
Rightmost charging case LED light flashing: Right earphone charging
Charging case LED lights off: Earphone Fully Charged
Note: It takes about 1.5 hours to fully charge the earphones
Charging Case Charging Status
Open and close the charging case cap
Lights on charging case stand for the remaining battery capacity
Note: It takes about 1.5-2 hours to fully charge the charging case
. 113 Battery Left
oo 23 Battery Left
ee e Fulychaged

Note
Please follow below steps when both earphones fail to pair with each
other or occur connection related issues
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone to power off both earphones
3. Touch and hold the power button of both earphones for 10
seconds with prompt sound ‘Power on first and then Power off
4. Putthe earphones back to the charging case
5. Delete ‘ENACFIRE F2 Bluetooth name from your phone
6. Turn on Bluetooth and reconnect the earphones

Safety Instruction ———————————
Using earphones at high volume for extended periods of time will
resultin permanent hearing damage. It is advised to keep the
volume level low at most of the time for your safety.
Do not use while driving, cycling, operating machinery or performing
other activities that require hearing surrounding sounds.
Do not use earphones in thunderstorm, the earphones may not
work properly under poor weather condition, and may increase the
risk of getting hit by lightning.
Earphones may not work properly under high temperature or high
humi
ity conditions,
Do not use any corrosive cleanser/oil to clean the earphones . If the
earphones come in contact with liquids, please quickly wipe it away.
Ifitis submersed in the water, do not turn the earphones on until it
is completely dried.
Tips: Man-made damage and lost are not covered under warranty.
Keep the earphones and the packaging out of reach of children.

Q&A
12
Q: Why the music get cut in and out sometimes?
A: Please make sure there is no obstacle between the earphones and
your device, Please make sure there is no Microwave oven / Wifi
transmitter around you, which are more likely to produce
electromagnetic interference and result in signal interruption.
Note: Please keep your phone and the earphone as close as possible
to ensure a more stable Bluetooth connection.
Q: What should | do if the earphones stop charging?
A We recommend you to charge the earphones by using our cable.
f our cable does not work, please try to use another charging cable
or power source to charge the earphones,
Q: How to contact ENACFIRE Customer Service Team?
A:Ifyou have any issue with the product, please contact us via
[email protected] (US/CA)
[email protected] (UK)
We will reply to you within 24 hours and 100% solve your issue.

FCCStatement
This equipment has been tested and found to comply with the limits
for a Class 8 digital device, pursuant to part 15 of the FCC Rules,
These limits are designed to provide reasonable protection against
harmful interference in a residential installation.
‘This equipment generates, uses and can radiate radio frequency
energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur ina
particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is
encouraged to try to correct the interference by one or more of the.
following measures;
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from
that to which the receiver is connected.
—Consult the dealer or an experienced radio/TV technician for help.

“This device complies with part 15 of the FCC Rules. Operation is
subject to the following two conditions:
(1) This device may not cause harmful interference
(2)this device must accept any interference received, including
interference that may cause undesired operation
Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate
the equipment.