Endless Pools SwimCross X500 User manual

SwimCross™Exercise Systems
OWNER'S MANUAL 50HZ
by Endless Pools®

OWNER’S MANUAL
This Owner’s Manual will acquaint you with the operation and general maintenance of your new SWIMCROSS Exercise
System. We suggest that you take some time to carefully review all sections. Please keep this manual available for
reference.
If you have questions about any aspect of your SWIMCROSS Exercise System’s set-up, operation or maintenance, contact
your authorized ENDLESS POOLS dealership. They are trained professionals who are familiar with the product, as well
as new SWIMCROSS Exercise System ownership concerns. Their expertise will facilitate the enjoyment of your new
SWIMCROSS Exercise System.
The serial number/identification label is located within the equipment compartment of your SWIMCROSS Exercise System.
The serial number should also be documented on the delivery receipt from your dealer.
IMPORTANT: Watkins Wellness reserves the right to change specifications, or design, without notification and without
incurring any obligation.
DATE PURCHASED: ___________________________________
DATE INSTALLED: _____________________________________
DEALER: ____________________________________________
ADDRESS: ___________________________________________
TELEPHONE: _________________________________________
MODEL/SERIAL NUMBER: ______________________________
COVER SERIAL NUMBER: ______________________________
In most cities and counties, permits will be required for the installation of electrical circuits or the construction of exterior surfaces (decks and
gazebos). In addition, some communities have adopted residential barrier codes which may require fencing and/or self-closing gates on the property
to prevent unsupervised access to the SWIMCROSS Exercise System by children. As a general practice, your local Building Department will
inform you of any applicable barrier requirements at the time a permit is obtained for the installation of an electrical circuit. Your dealer can provide
information on which permits may be required.
WELCOME
Watkins Wellness congratulates you on your decision to enjoy the finest SWIMCROSS Exercise System
available. Welcome to the growing family of SWIMCROSS Exercise System by ENDLESS POOLS
owners.

TABLE OF CONTENTS
SAFETY INFORMATION
IMPORTANT SAFETY INSTRUCTIONS .............................. 1
IMPORTANT SWIMCROSS EXERCISE SYSTEM
INSTRUCTIONS ..................................................................... 3
SITE REQUIREMENTS
INDOOR CONSIDERATIONS ............................................... 4
OUTDOOR CONSIDERATIONS........................................... 4
DECK INSTALLATION............................................................ 5
DELIVERY ACCESS .............................................................. 5
X500 MODEL .......................................................................... 6
ELECTRICAL REQUIREMENTS
220 - 240 VOLT PERMANENTLY CONNECTED ................ 7
EQUIPMENT COMPARTMENT ............................................ 8
DOOR PANEL REMOVE & REPLACE................................. 8
GETTING STARTED
MAIN SWIMCROSS EXERCISE SYSTEM
FEATURES.............................................................................. 9
HYDROMASSAGE JETS..................................................... 10
SWIM JETS ........................................................................... 10
WATERFALL VALVE............................................................. 10
AIR CONTROLS ................................................................... 10
DIVERTER VALVE................................................................ 10
QUICK START-UP INSTRUCTIONS .................................. 10
OPERATING INSTRUCTIONS
CONTROL PANEL................................................................ 12
SETTINGS............................................................................. 12
AUDIO IN.STREAM 2 (OPTIONAL).................................... 14
TEMPERATURE CONTROL .............................................. 14
JETS CONTROL................................................................... 14
SMART WINTER MODE ..................................................... 15
LIGHT CONTROL................................................................. 15
FILTER CYCLES................................................................... 15
POLLING ............................................................................... 15
ALL OFF / MEMORY ON ..................................................... 15
WI-FI IN.TOUCH™(OPTIONAL) ....................................... 15
WATER QUALITY AND MAINTENANCE
BASIC INFORMATION......................................................... 16
CHEMICAL SAFETY ........................................................... 16
HOW TO ADD CHEMICALS
TO THE WATER.................................................................... 16
FUNDAMENTALS OF
WATER MAINTENANCE ..................................................... 16
THE ENDLESS POOLS WATER MAINTENANCE
PROGRAM............................................................................ 18
VACATION WATER CARE INSTRUCTIONS..................... 19
GLOSSARY........................................................................... 20
CARE AND MAINTENANCE
FILTER MAINTENANCE ...................................................... 21
FILTER CARTRIDGE REMOVAL AND CLEANING
INSTRUCTIONS ................................................................... 21
DRAINING YOUR SWIMCROSS EXERCISE SYSTEM... 22
WINTERIZING YOUR SWIMCROSS EXERCISE
SYSTEM ................................................................................ 22
CARE OF THE PILLOWS ................................................... 22
CARE OF THE EXTERIOR.................................................. 23
SERVICE INFORMATION
GENERAL INFORMATION .................................................. 24
RCD AND HIGH LIMIT THERMOSTAT............................... 24
MISCELLANEOUS SERVICE INFORMATION.................. 24
ACTS INVALIDATING WARRANTY.................................... 24
DISCLAIMERS...................................................................... 25
WATKINS WELLNESS CUSTOMER SERVICE................ 25
TROUBLESHOOTING ......................................................... 25

Page 1
Safety Information
Safety InformatIon
IMPORTANT SAFETY
INSTRUCTIONS
(READ AND FOLLOW ALL
INSTRUCTIONS)
AVOIDING THE RISK TO CHILDREN
DANGER - RISK OF CHILD DROWNING
Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children cannot use a
SWIMCROSS Exercise System unless they are supervised at all times.
WARNING
To reduce the risk of injury, do not permit children to use this
SWIMCROSS Exercise System unless they are closely supervised at all
times.
• To reduce the risk of injury, lower water temperatures are
recommended for young children. Children are especially sensitive to
hot water.
• Extreme caution must be exercised to prevent unauthorized access
by children. To avoid accidents, ensure that children cannot use the
SWIMCROSS Exercise System unless they are supervised at all
times.
• The SWIMCROSS Exercise System should not be used by persons
(including children) with reduced physical, sensory or mental
capabilities, or lack of experience and knowledge, unless they receive
supervision or training.
DO:
• Make sure you always lock any child resistant locks after using the
SWIMCROSS Exercise System for your children’s safety.
• Test the water temperature with your hand before allowing children
to enter the SWIMCROSS Exercise System to be sure that it’s
comfortable.
• Remind children that wet surfaces can be very slippery. Make sure
that children are careful when entering or exiting the SWIMCROSS
Exercise System.
DON'T:
• Allow children to climb onto a SWIMCROSS Exercise System cover.
• Allow children to have unsupervised access to the SWIMCROSS
Exercise System.
AVOIDING THE RISK OF
ELECTROCUTION
DANGER - RISK OF ELECTROCUTION
• Connect only to a grounded source.
• Do not bury the power cord. A buried power cord may result in death,
or serious personal injury due to electrocution if direct burial-type cable
is not used, or if improper digging occurs.
• A ground terminal (pressure wire connector) is provided on the control
box inside the unit to permit connection of a minimum 8 mm²
solid copper bonding conductor between this point and any metal
equipment, metal water pipe, metal enclosures of electrical equipment,
or conduit within 1.5 m (5 feet) of the unit as needed to comply with
local requirements.
• Do not connect any auxiliary components (for example, cable,
additional speakers, headphones, additional audio components) to the
audio system unless approved by Watkins Wellness.
• Do not self service the audio component by opening or removing
SWIMCROSS Exercise System door panel as this may expose
dangerous voltage or other risk of injury. Refer all servicing to qualified
service personnel.
• Do not attach an external antennae to a SWIMCROSS Exercise
System audio system unless installed by a licensed electrician in
accordance with your National Electric Code.
WARNING
• To reduce the risk of electrical shock, replace a damaged cord
immediately. Failure to do so may result in death or serious personal
injury due to electrocution.
• In order to avoid a hazard due to inadvertent resetting of the thermal
cut-out, this SWIMCROSS Exercise System must not be supplied
through an external switching device, such as a timer, or connected to
a circuit that is regularly switched on and off by the utility.
• Always test the residual current device (RCD) before each use. If
the RCD does not perform properly, a ground current is flowing
indication the possibility of electric shock. Disconnect power to the
SWIMCROSS Exercise System until the fault has been identified and
corrected.
• NOTE: Failure to wait 30 seconds before resetting the RCD may
cause the SWIMCROSS Exercise System to not work properly, if this
happens, repeat the RCD test procedure.
• Your SWIMCROSS Exercise System must be supplied by a residual
current device (RCD) - with a tripping rating not exceeding 30 mA in an
electrical subpanel.
•
DANGER - RISK OF ELECTRICAL SHOCK
• Install at least 1.5 m (5 feet) from all metal surfaces. A SWIMCROSS
Exercise System may be installed within 1.5 m (5 feet) of a metal
surface if each metal surface is permanently connected by a minimum
10 mm² solid copper conductor attached to the wire ground connector
in the junction box that is provided for this purpose if in accordance
with your National Electrical Codes.
• Install your SWIMCROSS Exercise System in such a way that
drainage is away from the electrical compartment and from all
electrical components.
NO DIVING
Danger: Diving may result
in serious injury or death.

Page 2 Safety Information
• Do not permit any electrical appliances, such as a light, telephone,
radio, or television within 1.5 m (5 feet) of a SWIMCROSS Exercise
System. Failure to maintain a safe distance may result in death, or
serious personal injury due to electrocution, if the appliance should fall
into the SWIMCROSS Exercise System.
DO:
• Be sure your SWIMCROSS Exercise System is connected to the
power supply correctly - use a licensed electrical contractor.
• Disconnect the SWIMCROSS Exercise System from the power supply
before draining the SWIMCROSS Exercise System or servicing the
electrical components.
• Test the RCD before each use.
• Replace audio components only with identical components (if
your SWIMCROSS Exercise System is equipped with an audio
component).
DON'T:
• Use the SWIMCROSS Exercise System with the equipment
compartment door removed.
• Place electrical appliances within 1.5 m (5 feet) of the SWIMCROSS
Exercise System.
• Use an extension cord to connect the SWIMCROSS Exercise System
to its power source. The cord may not be properly grounded and the
connection is a shock hazard. An extension cord may cause a voltage
drop, which will cause overheating of the jet pump motor and motor
damage.
• Attempt to open the electrical control box. There are no user serviceable
parts inside.
RISKS TO AVOID
DANGER - RISK OF INJURY
• To reduce the risk of injury to persons, DO NOT remove suction
fittings, or filter standpipes located in the filter compartment.
• The suction fittings in the SWIMCROSS Exercise System are sized
to match the specific water flow created by the pump. Never replace
a suction fitting with one rated less than the flow rate marked on the
original suction fitting.
• There is a danger of slipping and falling. Remember that wet
surfaces can be very slippery. Take care when entering or exiting the
SWIMCROSS Exercise System.
• Never operate the SWIMCROSS Exercise System if the suction
fittings are broken or missing.
• People with infectious diseases should not use the SWIMCROSS
Exercise System.
• Keep any loose articles of clothing, long hair, or hanging jewelry away
from rotating jets or other moving components. Long hair should be
tied up or placed under a bathing cap.
• Safe water temperature for aquatic exercise is approximately
29.5°C (85°F).
• DO NOT use this SWIMCROSS Exercise System alone.
INCREASED SIDE EFFECTS OF MEDICATION
• The use of drugs or alcohol may cause unconsciousness with the
possibility of drowning.
• Persons using medications should consult a physician before using a
SWIMCROSS Exercise System; some medication may cause a user
to become drowsy, while other medication may affect heart rate, blood
pressure, and circulation.
• Persons taking medications which induce drowsiness, such as
tranquilizers, antihistamines, or anticoagulants should not use the
SWIMCROSS Exercise System.
HEALTH PROBLEMS AFFECTED BY
SWIMCROSS EXERCISE SYSTEM USE
• Pregnant women should consult a physician before using the
SWIMCROSS Exercise System.
• Persons suffering from obesity, or with a medical history of heart
disease, low or high blood pressure, circulatory system problems, or
diabetes should consult a physician before using the SWIMCROSS
Exercise System.
UNCLEAN WATER
• Keep the water clean and sanitized with correct chemical care. The
recommended levels for your ENDLESS POOLS SWIMCROSS
Exercise System are:
Free Available Chlorine:
1.0-5.0 ppm
Total Alkalinity:
80-120 ppm
Water pH:
7.2-7.8
Calcium Hardness:
75-150 ppm
• Refer to Water Quality and Maintenance section for complete
instructions.
IMPORTANT: Turn on the jet pump for at least ten minutes after adding
ANY SWIMCROSS Exercise System water chemicals into the swim
area.
Clean the filter cartridges monthly to remove debris and mineral buildup
which may affect the performance of the hydromassage jets, limit
the flow, or trip the high limit thermostat, which will turn off the entire
SWIMCROSS Exercise System.
AVOIDING THE RISK OF HYPERTHERMIA
Prolonged immersion in hot water can result in HYPERTHERMIA, a
dangerous condition which occurs when the internal temperature of
the body reaches a level above normal 37°C (98.6°F). The symptoms
of hyperthermia include unawareness of impending hazard, failure to
perceive heat, failure to recognize the need to exit the SWIMCROSS
Exercise System, physical inability to exit the SWIMCROSS Exercise
System, fetal damage in pregnant women, and unconsciousness
resulting in a danger of drowning.
WARNING
The use of alcohol, drugs, or medication can greatly increase the risk of
fatal hyperthermia in SWIMCROSS Exercise Systems.

Page 3Safety Information
TO REDUCE THE RISK OF INJURY
• The water in the SWIMCROSS Exercise System should never
exceed 40°C (104°F). Water temperatures between 26°C and 40°C
(79°F and 104°F) are considered safe for a healthy adult. The lower
water temperatures are recommended for extended use (exceeding
ten minutes) and for young children. Extended use can cause
hyperthermia.
• Pregnant or possibly pregnant women should limit SWIMCROSS
Exercise System water temperatures to 29.5°C (85°F) consult a
physician prior to using this product. Failure to do so may result in
permanent injury to your baby.
• Do not use the SWIMCROSS Exercise System having water
temperatures over 36°C (100°F) immediately following strenuous
exercise.
• Keep all breakables, especially glass, away from this SWIMCROSS
Exercise System.
• Never insert any objects into any openings.
• Keep all chemicals away from children and pets.
• DO NOT stack chemicals on top of one another.
• NEVER MIX CHEMICALS.
• Sanitizing chemicals must be stored separately from balancing chemicals.
AVOIDING THE RISK OF SKIN BURNS
• To reduce the risk of injury, before entering a SWIMCROSS Exercise
System the user should measure the water temperature with an
accurate thermometer.
• Test the water with your hand before entering the SWIMCROSS
Exercise System to be sure it’s comfortable.
SAFETY SIGN
Each ENDLESS POOLS SWIMCROSS Exercise System is shipped
with a SAFETY SIGN in the owner’s package. The sign, which is
required as a condition of Product Listing, should be permanently
installed where it is visible to the users of the SWIMCROSS Exercise
System. To obtain additional SAFETY SIGNS, contact your ENDLESS
POOLS dealer. Safety labels that are affixed to the shell are intended to
be permanent and should not be removed.
IMPORTANT
SWIMCROSS EXERCISE
SYSTEM INSTRUCTIONS
The following contains important SWIMCROSS Exercise System
information, and we strongly encourage you to read and apply them.
DO:
• Follow the SWIMCROSS Exercise System Care and Maintenance
recommendations stated in this manual.
• Use only approved accessories and recommended SWIMCROSS
Exercise System chemicals and cleaners.
• Provide adequate drainage to deal with overflow water.
DON'T:
• Leave the SWIMCROSS Exercise System exposed to the sun without
water or a cover in place. Exposure to direct sunlight can cause solar
distress of the shell material.
• Roll or slide the SWIMCROSS Exercise System on its side. This will
damage the siding.
• Lift or drag the vinyl cover by using the cover lock straps; always lift or
carry the cover by using the handles.
• Attempt to open the electrical control box. There are no user
serviceable parts inside. Opening of the control box by the
SWIMCROSS Exercise System owner will void the warranty. If you
have an operational problem, carefully go through the steps outlined in
the Troubleshooting section. If you are not able to resolve the problem,
contact your authorized ENDLESS POOLS dealer. Many problems
can easily be diagnosed over the telephone by an Authorized Service
Technician.
SWIMCROSS EXERCISE SYSTEM SHELL
Your SWIMCROSS Exercise System has an acrylic shell. Stains and
dirt generally will not adhere to your SWIMCROSS Exercise System’s
surface. A soft rag should easily remove most dirt. Most household
chemicals are harmful to your SWIMCROSS Exercise System’s shell
(see below for detailed information on cleaning agents). Always rinse
off any SWIMCROSS Exercise System shell cleaning agent with fresh
water.
IMPORTANT:
1. The following products are the ONLY approved cleaning agents
for your SWIMCROSS Exercise System shell: plain water, or Soft
Scrub®. The use of alcohol or any other household cleaner other
than those listed to clean the SWIMCROSS Exercise System shell
surface is NOT recommended. DO NOT use any cleaning products
containing abrasives or solvents since they may damage the shell
surface, specifically: Simple Green®, Windex®or spa Mitt. NEVER
USE HARSH CHEMICALS! Damage to the shell by use of harsh
chemicals is not covered under the warranty. Always rinse off any
SWIMCROSS Exercise System shell cleaning agent with fresh
water.
2. Iron and copper in the water can stain the SWIMCROSS Exercise
System shell if allowed to go unchecked. Ask your ENDLESS
POOLS dealer about a Stain and Scale Inhibitor to use if your
SWIMCROSS Exercise System has a high concentration of
dissolved minerals.
3. Keep all cleaners out of the reach of children and use care when
applying.
SAVE THESE INSTRUCTIONS

Page 4 Site Requirements
SIte requIrementS
Your SWIMCROSS Exercise System must be installed on a smooth
and level surface that can support the dead weight listed in the back of
this manual.
If a new slab is poured, consult your local electrical codes regarding
grounding and bonding. Local code may require a bonding wire to be
attached to the reinforcing bar or wire mesh that is embedded in the
concrete. If new concrete is being poured, this is the ideal time to install
the conduit for the incoming electrical supply.
Even if a new pad has been poured, it is essential that the system site
is level and planar. There is a simple way to ensure that this is the
case. First, draw a chalk outline of the footprint of your
SWIMCROSS
Exercise System. Place a 2 m (6 foot) level along and around the
footprint of the system. Verify that there are no gaps between the level
and floor. Next pour water inside of the chalk footprint. Verify that the
water does not puddle inside the footprint.
Should there a be a gap or should the water puddle inside the footprint,
call your Endless Pools dealer prior to continuing to discuss the best
way to resolve this situation.
INDOOR CONSIDERATIONS
1. Local electrical and plumbing codes.
2. Ventilation fans and/or dehumidifiers should be provided to handle
the humidity developed by your SWIMCROSS Exercise System.
Walls, ceiling and wood trim should be water resistant, also.
3. Chemicals will vaporize from the water and may cause an odor
and possibly corrosion to certain home hardware. Never store
chemicals inside the SWIMCROSS Exercise System cabinet.
4. During the normal use of the
SWIMCROSS Exercise System,
water will escape the vessel. Never place on or over any materials,
which may be damaged by this water or the chemicals within the
water. Keep damageable materials far enough away to avoid water
damage, even if the SWIMCROSS Exercise System should lose
all its water.
5. Consider and prepare for the unlikely event of rapid drainage. If
placement of the SWIMCROSS Exercise System is permanent,
you may wish to provide floor drains to accommodate draining, etc.
Always leave room all around the SWIMCROSS Exercise System
for easy access in case repairs are necessary.
6. Consider and prepare for the unlikely event of removal.
7. Do not set SWIMCROSS Exercise System on finished floor
without a waterproof barrier protection underneath.
8. The SWIMCROSS Exercise System should have access to a
power source capable of supplying 220-240 volts AC power. It
must be wired directly into a grounded circuit with an RCD. No
other appliances should be on the same circuit.
9. The SWIMCROSS Exercise System should be close to a source
of water.
10. Be sure that the location you choose is stable. It must be able
to support the weight of the SWIMCROSS Exercise System
when it is filled with water, plus the weight of the occupants.
The SWIMCROSS Exercise System may weigh up to 8,280 kg
(18,220 lbs) when it is filled with water.
11. Do not use the SWIMCROSS Exercise System above a finished
living area due to the risk of water damage.
12. The
SWIMCROSS Exercise System is not designed for in-floor
installation. However, it is compatible with a deck system that is
built flush with the bar top, provided you leave access for service.
13. Be sure to note any other considerations, such as aesthetics or
privacy concerns that may affect the safety or enjoyment of using
the
SWIMCROSS Exercise System.
OUTDOOR CONSIDERATIONS
1. Local electrical and plumbing codes.
2. Consider local codes pertaining to fencing, enclosures, walls,
electrical and plumbing. You will need to ensure that your
SWIMCROSS Exercise System is an adequate distance
from power lines, both above ground and underground. Your
SWIMCROSS Exercise System will also need to be child proofed.
3. View from house for aesthetics and supervisory needs.
4. Distance from house for wintertime soaking.
5. Nighttime lighting.
6. Consider sunlight exposure, views, access, property lines, lighting,
wind direction, shielding, septic tanks, plants, and trees when
determining your location. Chemicals in the SWIMCROSS
Exercise System water may splash damaging nearby plant life.
7. If your SWIMCROSS Exercise System is to be located on a
second story, be positive support is adequate. Call your builder and
a structural engineer.
8. Area for placement of support equipment where adequate space
will be needed to gain access to components for maintenance and
general servicing.
9. Be sure to note any other considerations, such as aesthetics or
privacy concerns that may affect the safety or enjoyment of using
the SWIMCROSS Exercise System.
10. Provide adequate drainage away from the equipment and
adequate elevation to allow draining by siphon, if should be
required.
11. Location of electrical supply. 220-240 volt systems require hard
wire installed from the main electrical source, to the sub panel,
then to the SWIMCROSS Exercise System terminal block. All
equipment must be RCD protected (NOT SUPPLIED) All electrical
wiring must comply with the national electric code.
12. Locations at least 1.5 m (5 feet) from all metal surfaces. A
S WIMCROSS Exercise System may be installed within 1.5 m
(5 feet) of metals surfaces providing each metal surface is
permanently connected by a 10 mm2 copper conductor attached to
the bonding wire connector on the heater provided for this purpose.
All installations must comply with your national electric codes.
13. Place the SWIMCROSS Exercise System on a firm, level surface
that will not shift.

Page 5
Site Requirements
DECK INSTALLATION
To be certain your deck can support your system you must know
the deck’s maximum load capacity. Consult a qualified building
contractor or structural engineer before you place the system on
an elevated deck. To find the weight of your system, its contents and
occupants, refer to the System Specification chart. This weight per
square meter must not exceed the structure’s rated capacity, or serious
structural damage could result.
DELIVERY ACCESS
It may be necessary to remove a gate, part of a fence, or other movable
obstructions in order to move the system to its installation site. Your
system will determine what equipment is necessary to move your system
to its final location. A roll back truck with a tilt bed is a good option if your site
can be accessed by an across road vehicle. When a small reach is needed
for the final placement of your system, a boom truck is ideal. A telehandler
vehicle can off load, traverse property and place your system in a more
challenging situation or terrain. When access to your site is limited a crane
may be used to lift your system over obstructions for precise placement.
The SWIMCROSS Exercise System delivery personnel will supervise
the crane delivery and complete the system installation. NOTE: If your
system delivery requires the use of a crane, you may be required to pay
for its services at the completion of the delivery.
How is your width and height clearance?
Protruding electric meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
Is the path clear?
Move away branches, dog
houses, firewood, etc.
If there is a 90 turn, can we
clear it? (The spa will not bend.)
No more than 6 consecutive
stairs without a landing
to accommodate the spa
Gas meters
Check all gates
HOUSE
BACK YARD
STREET
How is your width & height clearance?
Check all gates
Protruding electric meters
Gas Meters
A/C units
Do you have sufficient
overhead clearance?
Check low roof eaves,
overhanging branches,
rain gutters
Is the path clear?
Move away branches, dog
house, firewood, etc.
If there is a 90 turn, can we
clear it? (the SWIMCROSS
Exercise System will not bend)
No more than 6 consecutive
stairs without a landing
to accommodate the
SWIMCROSS Exercise
System

Page 6
X500 MODEL
457 cm
226 cm
41 cm 28 cm 41 cm
127 cm
107 cm
10 cm
NOTE:ENDLESS POOLS requires that the X500 Model be installed on a minimum 15 cm (6") thick reinforced concrete pad or structurally sound deck able to support the
“dead weight” found in the specification chart on the back page.
WARNING:The X500 Model must not be shimmed in any manner.
DOOR
DOOR SIDE
4.5 cm
ELECTRICAL CUTOUT
4.5 cm
ELECTRICAL CUTOUT
MAIN DRAIN
Site Requirements
TOP VIEW OF BASE

Page 7
electrIcal requIrementS
IMPORTANT : Fill the SWIMCROSS Exercise System with water before
turning on the power.
Your ENDLESS POOLS SWIMCROSS Exercise System has been
carefully designed to give you maximum safety against electrical shock.
Connecting the SWIMCROSS Exercise System to an improperly wired
circuit will negate many of the SWIMCROSS Exercise System’s safety
features. Improper wiring may also cause electrocution, risk of fire, and
other risks of injuries. Please read and follow the electrical installation
requirements and instructions completely!
220 - 240 VOLT PERMANENTLY
CONNECTED
ENDLESS POOLS SWIMCROSS Exercise Systems must be wired in
accordance with all applicable National and Local Electrical Codes. All
electrical work should be done by an experienced, licensed electrician.
We recommend the use of appropriate electrical conduit, fittings, and
wire for all circuits.
The diagram below illustrates how to wire the SWIMCROSS
Exercise System model:
• The SWIMCROSS Exercise System requires an electrical service
using a 40 amp breaker.
• The SWIMCROSS Exercise System can also run on a 24 Amp
electrical service however, you will NOT be able to run all three jet
pumps on high speed at the same time.
• One main disconnect switch with at least 3 mm separation
between contacts must be used for all electrical circuits.
• Mount the subpanel in the vicinity of the SWIMCROSS
Exercise System, but not closer than 1.5 m (5 feet)
away. Your
SWIMCROSS Exercise System, must be supplied by a residual
current device (RCD) - with a tripping rating not exceeding 30 mA in
an electrical subpanel.
• Open SWIMCROSS Exercise System by removing the 4 screws
holding the vertical T-spacer located in the center of the equipment
compartment (back side of SWIMCROSS Exercise System). Slide
panel towards center and remove, repeat for other panel.
• Insert power wires into SWIMCROSS Exercise System from either
side towards the bottom, you will find a plastic cap attached to wall.
• Once your SWIMCROSS Exercise System has been filled with
water, turn it on and test all of the circuit breakers.
IMPORTANT: If breaker immediately trips, verify that the wires are
correctly connected. Breaker should be tested prior to each use. Here’s
how:
1. Push the “TEST” button on each breaker - residual current device
(RCD), and observe it click OFF.
2. Wait 30 seconds, then push the breaker switch to the OFF (down)
position (to ensure that it has completely disengaged), then push
the breaker switch to the ON (up) position. If you don't wait 30
seconds, the SWIMCROSS Exercise System’s power indicator
may continue to blink – try again.
If any of the RCD breakers fails to operate in this manner, your
SWIMCROSS Exercise System may have an electrical malfunction,
and you may be at risk of electrical shock. Turn off all circuits and do
not use the SWIMCROSS Exercise System until the problem has been
corrected by an authorized service agent.
WARNING: Removing, or bypassing any RCD breaker will result in
an unsafe SWIMCROSS Exercise System and will void the warranty.
L1
N
G
L2
IMPORTANT: If you ever need to move or relocate your ENDLESS POOLS SWIMCROSS Exercise System, it is essential that you understand and
apply these installation requirements. Your ENDLESS POOLS SWIMCROSS Exercise System has been carefully engineered to provide maximum
safety against electric shock. Remember, connecting the SWIMCROSS Exercise System to an improperly wired circuit will negate many of its safety
features.
NOTE: Long wiring runs may require larger-gauge wire than stated.
220-240 VAC 50Hz
32A SERVICE,
FACTORY SETTING
(24A SERVICE)
(FIELD ADJUSTABLE)
RCD BREAKER
40 AMP (30A)
INPUT
MORE THAN 152 cm
THE SUB-PANEL MUST BE
WITHIN SIGHT OF THE
EXERCISE SYSTEM
DO NOT EXCEED 1525 cm
GND
GECKO Ye-5 HEATER/CONTROLLER
L1, HOT, 10 mm² BROWN
NEUTRAL 10 mm² BLUE
GROUND, 10 mm² GRN/YLW
L1, HOT
10 mm²
IMPORTANT: Using a 24A service will require a system modification, see Electrical Configuration on page 14 on how to
change the system settings.
10 mm²
N, NEUTRAL
Electrical Requirements

DOOR PANEL REMOVE & REPLACE
REMOVAL
1. Locate the vertical T-spacer in the center of the equipment compartment (back side of SWIMCROSS Exercise System).
2. Remove the 4 screws (using an 8 mm (5/16") socket) holding the T-spacer then remove the T-spacer.
3. Slide panel towards center until panel is no longer behind corner.
4. While holding panel, first pull panel up then pull bottom away from SWIMCROSS
Exercise System.
5. Lower panel to remove. Repeat for other side.
REPLACE
1. Raise panel making sure it goes behind the bar top then lower to rest on bottom frame.
2. Slide panel behind corner.
3. Replace other side panel using steps 1 & 2.
4. Attach T-spacer back in place using 4 screws to complete the installation.
EQUIPMENT COMPARTMENT
The illustrations below are to be used as a reference only (your SWIMCROSS Exercise System may look different). The equipment compartment is located
behind the hydromassage seats (back of the SWIMCROSS Exercise System).
1. Hydromassage Jets & Filter Pump
2. Swim Jets Pump
3. Control Box & Heater
4. Bonding Terminal
5. UVC Ozone
6. Bluetooth Music (optional)
7. Subwoofer (optional)
8. Wi-Fi (optional)
7
2
3
4
5
6
8
1
Page 8
CAUTIONS
USE COPPER CONDUCTORS ONLY.
USE SUPPLY WIRES SUITABLE FOR 75°C/167°F.
DISCONNECT ALL SUPPLY CONNECTIONS BEFORE SERVICING.
THESE SWIMCROSS EXERCISE SYSTEMS ARE INTENDED FOR
USE WITH GFCI/RCD SUBPANEL.
INCORRECT WIRING WILL DAMAGE CIRCUIT BOARDS.
REFER TO THE WIRING INSTRUCTIONS.
2
Electrical Requirements

Page 9
GettInG Started
MAIN SWIMCROSS EXERCISE
SYSTEM FEATURES
1 ) The control panel provides a quick visual
check of the SWIMCROSS Exercise System’s
status and allows the user to set different
functions of the SWIMCROSS Exercise System.
2) The Air Valve allows you to add air to your
hydromassage jets.
3) The Water Feature Valve adjusts the amount
of water that flows from the water feature
(2x).
4) The Diverter Valve allows you to change the
amount of water flowing through either the Swim
jets or River jet.
5) The Swim jets provide a strong flow of water
creating a current to swim against.
6) The River jets provide an adjustable strong
flow of water creating a current to swim against.
7) The Large Hydromassage jets provide a
unique, pulsating massage.
8) The Midsize Directional Hydromassage
jets, with eyeball nozzles, deliver a direct, more
focused massage.
9) The Midsize rotational Hydormassage jets,
provide a rotating massage.
10) The Mini Hydromassage jets feature a
direct more focused massage.
11) Pillow
12) Filter Compartment Grill (2x)
13) Swim Speaker (Optional)
14) Seating area Speaker (Optional)
15) Suction Screen
Getting Started
16) Water feature (2x)
17) Ozone Jet/Heater Return
18) Grab Rails
19) Points of Light
20) Exercise Anchor
21) Tether Anchor
1
2
4
5
6
10
11
12
13
3
8
17
14
ADDITIONAL SWIMCROSS EXERCISE
SYSTEM FEATURES
16
21
9
18
7
15
19
20
4
18
18
20

HYDROMASSAGE JETS
LARGE HYDROMASSAGE JETS - This jet provides a unique,
pulsating massage. The water flow is adjustable in that it can be turned
from low to high (by rotating the jet faceplate ¼ turn).
MIDSIZE DIRECTIONAL JET - These jets allow you to redirect the
jet stream by changing the position of the nozzle. The water flow is
adjustable in that it can be turned from low to high (by rotating the jet
faceplate ¼ turn).
MIDSIZE ROTATIONAL JET - These jets provide a rotating massage
pattern. The water flow is adjustable in that it can be turned from low to
high (by rotating the jet faceplate ¼ turn).
MINI JET - These jets deliver a direct, more focused massage. The
water flow is adjustable in that it can be turned from low to high (by
rotating the jet faceplate ¼ turn).
SWIM JETS
SWIM JET - The Swim Jet provides a powerful stream of water used
to simulate a water current that is adjustable by using the left diverter
valve.
RIVER JET - Raise or lower the River jet nozzle to simulate a water
current at or below your body during your swim. Rotate the right diverter
valve to change the strength of the water flow coming out of the jet.
WATERFALL VALVE
Your SWIMCROSS Exercise System is equipped with
a waterfall feature. It is activated by turning on the
hydromassage jets (either low or high speed). The flow
is regulated by turning the waterfall valve on the inside
wall of the SWIMCROSS Exercise System.
AIR CONTROLS
Your SWIMCROSS Exercise System is equipped with
two air valves. The air valves will add or remove air to
the hydromassage jet system. Rotate valve to see which
hydromassage jets are affected.
DIVERTER VALVE
Your exercise system is equipped with two diverter
valves. The left side regulates the amount of water
flow going through the Swim Jets while the right side
regulates the amount of water flowing through the River
jet. Turn to + for more flow or - for less flow.
QUICK START-UP INSTRUCTIONS
BEFORE YOU FILL YOUR SWIMCROSS
EXERCISE SYSTEM
Make sure your SWIMCROSS Exercise System has been properly
installed per all local codes, this includes the location of the
SWIMCROSS Exercise System, the foundation of the SWIMCROSS
Exercise System, as well as the electrical installation.
DO:
• Know which water treatment system you will be using and make sure
you have necessary chemicals available. Read all of the instructions
that come with the system.
• Have 5-way Test Strips Available.
• Have pH/Alkalinity Up & Down available.
• Know the hardness of your water, contact your dealer to help you
with this information. See Water Quality and Maintenance for more
information.
IMPORTANT: Watkins Wellness does not recommend that the
SWIMCROSS Exercise System be filled with “softened” water, as this
may damage the SWIMCROSS Exercise System’s equipment.
• Purchase the Clean Screen
™
pre-filter to remove unwanted
contaminants from the tap water. This is recommended, not required.
Page 10 Getting Started

Page 11Getting Started
START-UP
Your ENDLESS POOLS SWIMCROSS Exercise System has been
thoroughly tested during the manufacturing process to ensure reliability
and long-term customer satisfaction. A small amount of water may
have remained in the plumbing after testing and, as a result, may have
spotted the SWIMCROSS Exercise System shell or the SWIMCROSS
Exercise System siding prior to delivery. Before filling the SWIMCROSS
Exercise System, wipe the SWIMCROSS Exercise System shell clean
with a soft rag. The following instructions must be read and followed
exactly to ensure a successful start-up or refill.
CAUTIONS
• Do NOT fill the SWIMCROSS Exercise System with hot water, as
tripping of the high-limit thermostat may result.
• DO NOT CONNECT POWER TO AN EMPTY SWIMCROSS
Exercise System. Power to the SWIMCROSS Exercise System
automatically activates critical components within the SWIMCROSS
Exercise System, such as controls, heater, and other systems. If power
is supplied to these components prior to the SWIMCROSS Exercise
System being filled, the components will be damaged, and this may
result in a non-warranty component failure.
• DO NOT use your SWIMCROSS Exercise System after filling until all
of the steps listed below are completed.
• DO NOT add chlorine if treating your SWIMCROSS Exercise
System with polyhexamethylene biguanide (Biguanide, PHMB, eg.
BaquaSpa®) sanitizer.
• Before filling your SWIMCROSS Exercise System for the first time,
remove the equipment compartment door and check to ensure that the
unions on either side of the pump(s) and heater are hand-tight and the
slide valves are open.
1. CLOSE DRAIN, remove the filter compartment grill skimmer
tray and one filter (pg. 22). Fill your SWIMCROSS Exercise
System through the filter compartment using the CleanScreen™
pre-filter that attaches to your garden hose. The water level of your
SWIMCROSS Exercise System should be maintained at a level
15 cm (6") below the top of the SWIMCROSS Exercise System.
Reinstall the filter, skimmer tray, and grill once the SWIMCROSS
Exercise System is filled.
IMPORTANT: Watkins Wellness does not recommend that the
SWIMCROSS Exercise System be filled with “softened” water, as
this may damage the SWIMCROSS Exercise System’s equipment.
2. AFTER THE SWIMCROSS EXERCISE SYSTEM HAS BEEN
FILLED with water and the equipment compartment door is
secured, power must be applied to the SWIMCROSS Exercise
System.
• FIRST activate power to the subpanel from the main house panel.
• NEXT open the door of the electrical subpanel and reset the
GFCI/RCD breaker.
• FINALLY, close and secure the subpanel door.
3. TO CHECK THE OPERATION OF THE JET SYSTEM and to
purge any remaining air from the heating system complete the
following steps:
• Press the jets button and place all jet pumps on High.
• Once the jet system is fully operational (as indicated by strong,
non-surging jets), priming of the SWIMCROSS Exercise System
is complete.
• To turn off the jets, press all of the jets
button on the control panel
to turn off the jets.
• If you do not feel a steady stream of water from your jets, refer
to the instructions for priming the pump in the SWIMCROSS
Exercise System TROUBLESHOOTING section.
4. SET THE TEMPERATURE CONTROL to the desired
temperature between 15°C (59°F) and 40°C (104°F), then place
the SWIMCROSS Exercise System cover on the SWIMCROSS
Exercise System and allow the water temperature to stabilize
approximately 0.5°C (1°F) per hour. Make sure you secure the cover
in place. Periodically check the SWIMCROSS Exercise System
water temperature. When the water temperature reaches desired
temperature, proceed to the next step. The SWIMCROSS Exercise
System temperature is pre-programmed to reach 29.5°C (85°F).
You may change the water temperature by pressing the  button
on the control panel to raise the temperature, or lower temperature
by pressing the ▼button.
5. USING A TEST STRIP AND APPLICABLE CHEMICALS adjust
Total Alkalinity (TA) to 80 - 120 ppm, Calcium Hardness (CH) to
75 - 150 ppm, then SWIMCROSS Exercise System water pH to
between 7.2 and 7.8. These procedures are listed in the “Water
Quality and Maintenance” section.
OPERATION NOTE: Adjusting the Total Alkalinity as the first step
is important, as out-of balance TA will affect your ability to adjust the
pH correctly and will prevent the sanitizer from operating effectively.
IMPORTANT: Activate all the jets (press the jets buttons and place
all jet pumps on high for 10 minutes) before adding chemicals.
Disperse the chemicals in the swim area away from the walls.
6. SUPERCHLORINATE the SWIMCROSS Exercise System
WATER by adding 1½ teaspoons of chlorine (sodium dichlor) per
950 liters (250 gallons) of water while running the jets on high for 10
minutes. Disperse the chemicals in the swim area away from the
walls.
7. TEST THE SWIMCROSS Exercise System WATER FOR
CHLORINE RESIDUAL. If the residual is between 1 and 5 ppm on
the test strips, go on to the next step. If the residual is less than 3
ppm, activate the jets on high speed for another 10 minutes and add
more chlorine as needed, then retest.
WARNING:High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the SWIMCROSS Exercise
System.
8. RECHECK the Total Alkalinity (TA) 80 - 120 ppm, Calcium
Hardness (CH) 75 - 150 ppm, and the pH must be between
7.2 and 7.8.
The SWIMCROSS Exercise System is ready for use when the
SWIMCROSS Exercise System water has circulated and the bromine
level remains between 1 and 2 ppm or chlorine level remains
between 1 and 5 ppm.
OPERATION NOTE: For proper water circulation during the ten-
minute cycle place the air control switches in OFF position.

Page 12
operatInG InStructIonS
CONTROL PANEL
The control panel provides a bright, full color display, and intuitive user
experience, while its screen’s high resolution brings SWIMCROSS
Exercise System user interfaces to a new level. Loaded with a large
amount of memory and a powerful on-board processor creating
seamless graphic interface that SWIMCROSS Exercise System users
have been waiting for.
CONTROL PANEL FUNCTIONS
When the screen is off, press any button to turn the control panel screen
on and display the home screen. After 30 minutes of inactivity the screen
will shut off.
The function description of the buttons below will only work from the
Home screen. Once the control panel is placed in a submenu the
selection lights next to the buttons will light up to indicate which buttons
may be selected for a specific screen function.
SETTINGS
One press of the (Settings button) from the home page gives you
access to a menu to manage the settings of your SWIMCROSS
Exercise System where you will find:
• Water care
• Audio (optional)
• Maintenance
• Date and time
• Keypad Settings
• Miscellaneous
• Wi-Fi (optional)
• Electrical configuration
• About
Use the or buttons to move up and down in the list. To select an
option, press the lit button beside the desired highlighted option.
IMPORTANT: At any point you can press the (Settings button) to
return to the home screen or top left button (hydromassage jets) to go
back.
WATER CARE
The Water Care section will help you
set up your ideal filtration and heating
settings. Choose from Away from Home,
Standard, Energy Savings, Super Energy
Savings, and Weekender, depending on
your needs.
Use (middle left) button to choose your setting. A green checkmark
will appear on the selected icon to confirm.
When in Economy mode, the heating set point will be reduced by 11°C
(20°F), which means that the heating system will not come on during
the set time unless the temperature falls 11°C (20°F) below the set
temperature.
The filtration schedule shown on the screen will apply to the main
filtration pump (hydromassage jets).
WATER CARE MODES
Away from home:
In this mode the System will always be in economy mode; the
set point will be reduced by 11°C.
Standard:
The System will never be in economy mode and will be
filtering according to the pack's low level configuration.
Energy Savings:
The System will be in economy mode during the peak hours of
the day and resume normal mode on the weekend*.
Super Energy:
The System will always be in economy mode during peak
hours, every day of the week*.
Weekender:
The System will be in economy mode from Monday to Friday,
and will run normally on the weekend*.
Default Settings:
By selecting this setting you will be asked to confirm your
choice. Doing so will revert all Water Care Modes back to
factory settings.
*Filtration will be reduced when the economy mode is active.
MODIFYING SCHEDULES
To modify a Water Care category, use
the (middle right) lit button, to
open the selected Water Care menu.
The menu screen is divided into two
settings, Economy and Filter cycle with
Economy being first. Set or change the
Day, Start and Stop time if desired to
keep the heater off (Economy
mode). Scroll down to set or
change the Filter cycle Day, Start
and Duration.
You can add schedules by scrolling
down to Add, and selecting by
using the (middle left) lit button.
To delete a schedule, press (top right) lit button.
Settings
Audio
Top
Swim Jets
Selection Lights
Bottom
Swim Jets
Hydromassage Jets All Off/Memory On
Up/
Temperature
Down/
Temperature
Exterior
Lights
(Optional)
Interior Lights
Operating Instructions

Page 13
You can modify the programmed schedules by selecting one (middle
left) lit button and adjusting the schedule using the or buttons.
Press (middle left) lit button to move between parameters.
You have several possibilities for the schedule (Mon-Fri, weekend, every
day, or single days). The schedules will be repeated every week. The
time and duration are set in 30 minute increments. Once you have set
the schedule, use (top left) lit button to go back. Ensure that you
have selected the desired Water Care option in the main Water Care
menu.
MAINTENANCE
From the Settings page you can
access the Maintenance menu,
which gives you access to the
following options:
• Maintenance reminders
• Standby
Use the or buttons to make
a selection, and (middle left) lit button to select.
MAINTENANCE REMINDERS
The control panel will remind you
of maintenance required on your
SWIMCROSS Exercise System, like
rinsing or cleaning the filter. Each
task has its own duration, based on
normal use.
The Maintenance reminders menu
allows you to verify the time left before maintenance is required, as well
as to reset the time once a task is completed.
Use the or buttons to move through the list.
To reset a task select it by pressing the (middle left) lit button, then
confirm by pressing the lit button next to confirm when prompted. Once
you have confirmed the task will be reset.
STANDBY
The Standby mode allows you to
service your System. Pumps will stop
for 30 minutes, and automatically
restart after this time. Press
(middle left) lit button to activate
Standby mode.
Once Standby mode has been
activated a screen will appear to show that pumps are stopped. The
normal page will return at the end of maintenance.
Press on the button next to cancel to leave Standby mode and restart the
SWIMCROSS Exercise System.
DATE AND TIME
Here you can adjust the time
format, change the year, date, and
time. Use the or buttons to
choose the setting that you want to
adjust, and select it by pressing
(middle left) lit button.
Use the or buttons to
change the parameters, and
(middle left) lit button to move between parameters. Press (top left)
lit button to take you back to the main Settings menu.
KEYPAD SETTINGS
In this section, you can change the
temperature unit, language, display
orientation, rim around the control
panel light color, and lock the control
panel.
Use the or buttons to
choose the setting that you want to
adjust. Select it by pressing the
(middle left) lit button then use the or buttons again to change the
setting.
When you change the display orientation, the contextual options and
or buttons adjust to the chosen orientation. The Audio and Setting
buttons remain unchanged, as well as the jets and lights buttons in the
home page.
Security settings allow you a Partial (Temperature) lock or Full (entire
control panel) lock. Select Security screen by pressing the
(middle
left) lit button then use the or buttons to change to Full, Partial or
Unlock. Press (top left) lit button to display an information screen
telling you to press and hold button for 5 seconds to lock.
To unlock Full, press and hold button for 5 seconds.
MISCELLANEOUS
You can turn the Warm weather
mode ON or OFF. When ON
the filtration pump will shut OFF
whenever the water temperature
gets 1°C (2°F) above the set
point. Because of the Recreation
system's large body of water it is
recommended to keep the Warm weather mode OFF.
Press the (middle left) lit button, then use the or buttons to
change the Warm weather mode.
You can also hide some information on the home screen by selecting
Hide in "Info messages" (not recommended).
ELECTRICAL CONFIGURATION
DO NOT make changes to this section unless you are a qualified
electrician!
Use only to convert to 24 Amp!
• Press the (Settings) button from the home page .
• Press the button to move down the list until Electrical Config. is
displayed next to center lit button.
• Press the (middle left) lit button to access Electrical Config. screen.
• Press and hold (lower right) lit button for 5 seconds to Confirm.
• Press the button to select Input current.
• Press the (middle left) lit button to enter Input current.
• Press the button changing Input current from 32A to 24A
• Press the (middle left) lit button to enter and reboot system.
ABOUT
This section shows information about the control panel software number,
and the revision numbers of the different components of your system.
Operating Instructions

Page 14 Operating Instructions
WI-FI (OPTIONAL)
This menu allows you to connect
your in.touch module to a Wi-Fi
network or to change its network.
This menu is only visible when the
in.touch module is installed.
To connect your in.touch module
to a wireless network, use the
or buttons to go to the Wi-Fi
option in the Settings menu and (middle left) lit button to
select it.
After a few seconds the available networks will appear on the screen, as
well as their signal strength.
Use the or buttons to
move through the list. Select your
network by pressing the middle left
button (top swim jets).
If the Wi-Fi network is password
protected enter it when prompted.
• Use the or buttons to
choose your letters.
• Use (lower right) lit button to move the curser forward.
• Use (top right) lit button to change the type of character.
(uppercase, lowercase, number, symbol).
• Use (lower left) lit button to backspace.
• Use (middle left) lit button to confirm.
If no password is required the in.touch
will connect automatically.
Once the in.touch module is connected
to a Wi-Fi network a green check mark
will appear in the Wi-Fi menu, and
the network name will appear in the
Settings menu.
AUDIO IN.STREAM 2 (OPTIONAL)
If your SWIMCROSS Exercise System has the optional in.stream 2
Bluetooth with subwoofer system the following screens and functions will
be available on the control panel:
AUDIO
The control panel is used with the in.stream 2 audio system. The Audio
screen in the Settings menu gives
you the option to disconnect your
Bluetooth enabled device, adjust the
Fader, Balance or Sub Woofer.
Use the or buttons to scroll
to desired option, press (middle
left) lit button to select the function.
Press the or buttons to
change parameters. Press (top
left) lit button to take you back to the main Settings menu.
IN.STREAM 2 FUNCTIONS
Press the button in the home screen to access your audio system.
If you are using a device with Bluetooth technology, it must be connected
for functions to work.
Please note that the Play/Pause and Change Track functions apply to
devices using Bluetooth technology only, and will NOT work when AUX
is selected as the source.
TURNING POWER ON/OFF
Press the (top right) lit button to start the audio on or off process.
SELECTING THE SOURCE
Press the (top left) lit button
to select a source using
Bluetooth wireless technology
or AUX (AUX is not available at
time of publication). Selection
will be indicated below in.stream
2.
PAIRING BLUETOOTH
Audio Power must be on. Go to the Bluetooth settings on your device
and find in.stream 2 and press to connect. Enter pin 5555 and press pair
to sync your device. NOTE: Only one device at a time can be synced.
PLAY/PAUSE AUDIO
Press the Play/Pause (middle right) lit button to start or pause the
audio. Press (middle left) lit button to mute or enable sound.
ADJUSTING THE VOLUME
Press the or buttons to increase or decrease the volume
illustrated by the slider bar.
CHANGING TRACKS
Use the Last Track and Next Track (lower left) lit button or
(lower right) lit button to change tracks.
TEMPERATURE CONTROL
The set temperature range is from 15°C to 40°C (59°F to 104°F). (The
water temperature of any SWIMCROSS Exercise System may rise
or lower slightly depending on the current use and condition of your
SWIMCROSS Exercise System and on outside temperatures.)
The set temperature of the SWIMCROSS Exercise System water will
automatically be 29.5°C (85°F) the first time power is applied. This is
the setting programmed at the factory. After the SWIMCROSS Exercise
System has been set up and used, the last temperature value set by
the user will be stored in memory. If power is disconnected from the
SWIMCROSS Exercise System, it will automatically revert to the last set
temperature when power is reapplied.
To display the set temperature of the SWIMCROSS Exercise System:
Press the or buttons on the
control panel in the home screen.
To increase the set temperature of
the Exercise System:
Press the button in the home
screen. The set point will appear in
blue. After 3 seconds without any
change to the set temperature
value, the current water temperature will reappear in white.
To decrease the set temperature of the SWIMCROSS Exercise System:
Press the button in the home screen. The set point will appear in blue.
After 3 seconds without any change to the set temperature value, the
current water temperature will reappear in white.
JETS CONTROL
When pressed, the three buttons on the left of the screen will activate the jets
when in the home screen. If left running the low or high speed pumps will
automatically turn off after 2 hours.

Page 15
HYDROMASSAGE JETS
Turn the hydromassage jet pump On to activate all of the hydromassage
jets in the seated area as well as the waterfall if the waterfall valve is
open. This pump has a low speed and high speed mode.
This jet pump will automatically turn on in low speed when the system is
calling for heat or the filtration cycle.
Press jet button to activate the
hydromassage jets in low speed, you
will see the jet 1 icon on the screen
rotate slowly.
Press jet button a second time to
place the hydromassage jets in a high
speed, you will see the jet 1 icon on
the screen rotate faster.
Press jet button a third time to shut the hydromassage jets off.
SWIM JETS - TOP 3 JETS
The SWIMCROSS Exercise System uses a 2.5 Horsepower single
speed pump to power the top 3 swim jets.
Press jet button to activate the top row of jets (swim area) in high
speed, you will see the jet 2 icon on the screen rotate fast.
Press jet button a second time to shut the top row of jets off.
SWIM JET - RIVER JET
The SWIMCROSS Exercise System uses a 2.5 Horsepower single
speed pump to power the River jet.
Press jet button to turn the River jet in the swim area on, you will
see the jet 3 icon on the screen rotate fast.
Press jet button a second time to shut the River jet off.
SMART WINTER MODE
The Smart Winter Mode (SWM) is used to prevent water from freezing in
the plumbing lines. As soon as there is a risk of freezing, this protection
automatically kicks in. The SWM protection will turn back off only after
24 hours without a risk of freezing. During the SWM period, the Smart
Winter Mode icon remains on; the icon blinks when the purge is active.
The purge period indicates the amount of time between the purging of
the plumbing lines based on the temperature behind the panels.
LIGHT CONTROL
All SWIMCROSS Exercise Systems are equipped with a interior lighting
system. This system includes points of lights located throughout the
SWIMCROSS Exercise System.
Press the (lower right) button (when
in the home screen) to activate the
internal lights and left light icon.
Press the (lower right) button a
second time to shut the lights off, when
turning back on after several seconds
the same light mode will appear.
Every time the light is turned off and on quickly a new light mode will
appear.
The sequence is as follows: White, Aqua, Magenta, Azure, Amber,
Emerald, Ruby, color wheel with abrupt color changes, slow full color
wheel and fast full color wheel.
NOTE: If left on, the light will automatically turn off after 4 hours of operation.
EXTERNAL LIGHTS (OPTIONAL)
Press the (middle right) button (when in the home screen) to activate
the external lights and right light icon. Press a second time to turn off.
FILTER CYCLES
When your SWIMCROSS Exercise System is first powered up, the
default filter cycle is set to start at 12:00 pm and will run for 5 hours each
day using the Standard Water Care mode. Unless you set the time using
the control panel (see Date & Time under Settings) the SWIMCROSS
Exercise System filter cycle will start at power up and run for 5 hours and
repeat every 24 hours.
We recommend setting your date and time first then going to the Water
Care section and making any desired changes for days, start times and
length of time in the desired Water Care Mode.
The filter cycle will activate the hydromassage jets on low speed for the
entire cycle that has been programmed.
NOTE: Power interruption of the SWIMCROSS Exercise System will not
change the filter cycle settings when power is regained.
FILTER CYCLE SUSPENSION:
The filter cycle will be suspended every time a jet pump or light
is activated manually during the filter cycle time. The suspension
will end 10 minutes after the completion of the manual use.
POLLING
Polling is necessary for your Exercise System to maintain the proper
set temperature. The temperature probe located inside the heating
tube requires water from the hot tub to pass through it, this is done by
automatically turning on your filtration pump for approximately 2 minutes.
Outside temperatures will determine how often the pump is turned on,
this can range anywhere from 15 to 90 minute intervals.
ALL OFF / MEMORY ON
Press the (top right) button when
in the home screen to turn the lights
and any jets that are on OFF. It will
not turn the music system off.
If you press this button again before
pressing the light or jets button it
will bring up the last settings before
shutting off.
NOTE: The color of the lights will
however advance to the next sequence.
WI-FI IN.TOUCH (OPTIONAL)
If your SWIMCROSS Exercise System is equipped with the Wi-Fi
in.touch module you will be able to use the internet or your home Wi-Fi
network to control your SWIMCROSS Exercise System by downloading
an App to your favorite devices.
See Wi-Fi in the Settings section to connect your SWIMCROSS
Exercise System to your home Wi-Fi network.
For instruction on how to download the App to your device search "gecko
in.touch" in your App store. For more instructions go online to the in.touch
setup guide:
http://www.geckoalliance.com/Documents/intouch_
setupguide_d_en.pdf
Operating Instructions

Page 16
Water qualIty and
maIntenance
BASIC INFORMATION
It’s important to have clean water. Water maintenance is one of the least
understood, yet most important areas of SWIMCROSS Exercise System
ownership. Your dealer can guide you through the process of achieving
and maintaining balanced water in your SWIMCROSS Exercise System,
given your local conditions.
IMPORTANT: Water Terminology can be found at the end of this
section.
• Always read & refer to the owner's manual for complete information.
• Test your water with a test strip once a week, or each time the
SWIMCROSS Exercise System is used.
• Add chemicals in frequent, small amounts to prevent overdosing the
SWIMCROSS Exercise System.
• Use the SWIMCROSS Exercise System only when the chlorine level
is between 1-5 ppm or manually add chlorine as needed.
• It is the SWIMCROSS Exercise System owner's responsibility to
prevent over or under chlorination.
IMPORTANT: It is recommended at a minimum to change 50% of your
water every year; however, it is dependent on the amount of usage.
Check with your ENDLESS POOLS dealer to determine if water in your
region has unique qualities - such as high metal or mineral content - that
should be addressed.
WATER QUALITY CHART
PARAMETER TARGET MIN - "OK" RANGE - MAX
pH 7.4 7.2 7.8
ALKALINITY 100 ppm 80 ppm 120 ppm
HARDNESS 100 ppm 75 ppm 150 ppm
CHLORINE 3 ppm 1 ppm 5 ppm
Maintaining the water quality and the cleanliness of the filters in your
SWIMCROSS Exercise System is your responsibility. Keeping the
SWIMCROSS Exercise System water balanced prolongs the life of the
components and will make the water more comfortable. Your program
will depend on your water’s mineral content, how often you use your
SWIMCROSS Exercise System, and how many people use it. Watkins
Wellness has developed several water care systems and products to
simplify water care which are available from authorized ENDLESS
POOLS dealers.
CHEMICAL SAFETY
When using chemicals, read the labels carefully and follow directions
precisely. Though chemicals protect you and your SWIMCROSS
Exercise System when used correctly, they can be hazardous in
concentrated form. Always observe the following guidelines:
• Allow only a responsible person to handle SWIMCROSS Exercise
System chemicals. Keep them out of the reach of children.
• Accurately measure the exact quantities specified, never more. Do not
overdose your SWIMCROSS Exercise System.
• Handle all containers with care. Store in a cool, dry, well ventilated
place.
• Always keep chemical containers closed when not in use. Replace
caps on their proper containers.
• Don't inhale fumes, or allow chemicals to come in contact with your
eyes, nose, or mouth. Wash your hands immediately after use.
• Follow the emergency advice on the product label in case of accidental
contact, or if the chemical is swallowed. Call a doctor or the local
Poison Control Center. If a doctor is needed, take the product container
along with you so that the substance can be identified.
• Don't let chemicals get on surrounding surfaces or landscaping. Don't
use a vacuum cleaner to clean up chemical spills.
• Never smoke around chemicals. Some fumes can be highly flammable.
• Don't store any chemicals in the SWIMCROSS Exercise System
equipment compartment.
HOW TO ADD CHEMICALS
TO THE WATER
IMPORTANT: All SWIMCROSS Exercise System water chemicals, must
always be dispersed into the swim area while all jet pumps are running
on high, and must run for a minimum of ten minutes.
TO ADMINISTER SWIMCROSS EXERCISE
SYSTEM WATER CHEMICALS:
1. Fold back the cover.
2. Turn all 3 jets systems ON, run for 10 minutes and turn OFF.
3. Carefully measure the recommended amount of chemical and
disperse into swim area while jets are on. Use care not to splash
chemicals on your hands, in your eyes, on the SWIMCROSS
Exercise System sheet surface, or on the siding.
Risk of Drowning: Never leave an open SWIMCROSS Exercise
System unattended!
WARNING: High sanitizer levels can cause discomfort to the user’s
eyes, lungs and skin. Always allow the sanitizer level to fall to the
recommended range before using the SWIMCROSS Exercise System.
IMPORTANT “SUPER CHLORINATION/NON-CHLORINE SHOCK
TREATMENT” NOTE: After administering a super chlorination treatment
or non-chlorine shock to your SWIMCROSS Exercise System, leave
the cover open for a minimum of 20 minutes to allow the oxidizer gas to
vent. A high concentration of trapped oxidizer gas which may exist as a
result of the shock treatment (not daily sanitation) may eventually cause
discoloration or vinyl degradation to the bottom of the cover.
FUNDAMENTALS OF
WATER MAINTENANCE
• Testing: Test the water weekly or each time the SWIMCROSS
Exercise System is used with convenient test strips or more accurate
liquid / tablet reagent test kit per instructions. Critical parameters:
sanitizer level, pH, Calcium Hardness (CH), and Total Alkalinity (TA).
Store test equipment in a dark, cool, dry place to maintain potency.
Water Quality and Maintenance

Page 17
• Chemical Balance/pH Control: It is important to adjust the primary
water parameters (Total Alkalinity, Calcium hardness, pH) into the
recommended ranges so that they are stabilized or balanced. Balance
the water chemistry every time you fill the SWIMCROSS Exercise
System with new water and then during the life of that body of water.
Keeping the water in balance prevents damage by holding the pH in a
safe range and preventing calcium scale formation on SWIMCROSS
Exercise System equipment. A low pH can damage metal components
whereas a high pH can cause high levels of calcium to form scale. Your
dealer should provide a detailed water chemistry orientation soon after
your new SWIMCROSS Exercise System is filled for the very first time.
• The following three water components must be kept in balance to avoid
damage to the SWIMCROSS Exercise System. Do balance these
components in the order they are listed here as each will help you
balance the next using a minimum amount of chemicals.
1. Calcium Hardness (CH) – CH is the measure of the amount of
dissolved calcium in the water. Low levels can make the water
corrosive and high levels cause scale formation on SWIMCROSS
Exercise System components. The recommended CH reading is
between
75 - 150 ppm. If the CH level is too high, lower it with the calcium
remover per instructions. Once in balance, the CH reading normally
remains stable until more water is added. Great care must be
taken when filling the SWIMCROSS Exercise System from a water
softener to ensure that the calcium remains in balance and avoid
damage to the SWIMCROSS Exercise System.
2. Total Alkalinity (TA) - TA is a measure of the water’s ability to
resist changes of pH or buffer capacity. A low TA allows the pH
to fluctuate easily. The recommended TA reading is between
80 - 120 ppm. To raise the TA, use pH/Alkalinity Up (sodium
hydrogen carbonate). To lower the TA, use pH/Alkalinity Down
(sodium bisulfate). We recommend you check the TA reading once
per month. Raising/lowering the TA may cause the pH readings to
fluctuate widely. Ignore the pH readings on the test strip while you
are balancing the TA.
3. pH - The pH is the measure of the acidity and alkalinity.
Maintaining the proper pH level will optimize the effectiveness of
the sanitizer, preventing damage to the SWIMCROSS Exercise
System and physical
discomfort for
SWIMCROSS Exercise
System users. A low
pH dissipates sanitizer,
causes corrosion, and
irritates SWIMCROSS
Exercise System users.
A high pH level will
neutralize sanitizer,
promote scaling and
cloud water. The
recommended pH
reading is between
7.2 - 7.8. To lower the pH level, use pH/Alkalinity Down (sodium
bisulfate). To raise the pH level, use pH/Alkalinity Up (sodium
carbonate).
• Water Conditioners: SWIMCROSS Exercise System fill water varies
from location to location and user to user, therefore it is important to
consult with your dealer for an appropriate program.
CLEAN SCREEN pre-filter –The CLEAN SCREEN pre-flter should
be used at every fill and top-off to remove contaminants from the fill
water, especially iron, copper, and manganese. Many water sources,
including well water, contain high concentrations of minerals that can
cause staining of the shell and plastics.
• Oxidizers: Ozone and Monopersulfate (MPS) are oxidizers used to
prevent the buildup of contaminants, maximize sanitizer efficiency,
minimize combined chlorine, and improve water clarity. They are
to be used in conjunction with EPA registered sanitizers. The UVC
Ozone system combines the Corona Discharge generator and a UVC
lamp. The UVC lamp kills and damages bacteria DNA on contact
providing a maximum water sanitation solution. Chlorine-Free Oxidizer,
Monopersulfate (MPS) is a granular oxidizing chemical.
• Sanitizers: Maintaining the recommended residual level of an EPA
registered sanitizer at all times will decrease the occurrence of unsafe
bacteria and viruses in your SWIMCROSS Exercise System water.
The recommended Free Available Chlorine (FAC), the amount of
available chlorine sanitizer, is 1 - 5 ppm. A low FAC can allow bacteria
and viruses to grow rapidly in the warm water, and a high FAC can
cause discomfort to the user’s eyes, lungs, and skin. Each sanitizer
carries its own instructions regarding how much to use and when to
add it to the SWIMCROSS Exercise System water. Consult your dealer
for their recommendations and instructions on proper sanitizing of the
SWIMCROSS Exercise System.
Watkins Wellness recommends the following sanitizer:
• Sodium Dichloro-s-Triazinetrione (sodium dichlor or chlorine)
• Biguanide
• Liquid sodium hypochlorite (do not use splashless)
WARNING: DO NOT use tri-chlor chlorine, bromo-chloro-dimethyl-
hydantoin (BCDMH), or any type of compressed bromine or chlorine,
acid or any type of sanitizer which is not recommended by Watkins
Wellness.
8.2
7.8
7.6
7.4
7.2
6.8
pH
ALKALINE
WATER
(SCALING
ZONE)
ADD pH
DECREASER
TO LOWER
pH
ADD pH
INCREASER
TO RAISE
pH
ACIDIC
WATER
(CORROSIVE
ZONE)
COMFORT
ZONE IDEAL
Water Quality and Maintenance