Endon Middleton EL-40017 User manual

Middleton Outdoor Wall Light
Safety Warnings
INSTRUCTION MANUAL
Endon Lighting, LS9 0SE
Assembly/ User Instructions
Before you start
Please read these instructions carefully before tting and retain for reference. Check the packaging and make
sure that you have all the required parts. Follow each assembly step in order to prevent incorrect assembly.
Ensure that the product is fully assembled as illustrated before use.
The Light pack contains:
Light tting.
Terminal connection block(s).
Fixing pack.
The following tools may be required:
Selection of cross and at head screwdrivers.
Electric drill and assorted drill bits.
Wire strippers.
Electrical insulation tape.
These assembly diagrams are intended as a guide – if in doubt consult a qualied electrician.
Care Information
Allow 10 minutes to cool before replacing, adjusting or cleaning.
Clean with a dry cloth only. Do not use liquid or abrasive cleaners on this product.
EL-40017-Middleton-WB 20161117
1. Decide on the position of the light tting, or remove existing light tting. Note of position of the electrical
connections, and ensure there is a solid mounting surface, preferably a brick or block wall, to support the
weight of the light tting.
2. Remove the two side screws and retain for re-use. Separate the lamp cover and diffuser from the wall plate,
then use the wall plate as a template to mark and make the screw holes.
• This product is only suitable for connection to a 240V~50Hz supply in accordance with current IEE wiring
regulations. It should be installed in accordance with local building regulations and is for domestic use only.
• Before commencing installation of your light tting always switch off the mains supply and remove the
appropriate fuse or switch off the appropriate circuit breaker.
• This is a Class I product, and must be Earthed. The terminal blocks are supplied according to requirements
of the tting.
• Run supply wire from a 5-amp electrical supply protected by an RCD using double insulated 3-core cable
of type H05RN-F 1.0mm2 (not supplied) to selected site, ensuring it is adequately protected through the full
length of the cable run, it must come out of the at surface of the wall or steps in line with the entry to the
tting.
• Except where installed in a conduit or duct which provides equivalent protection against mechanical damage,
a cable buried in the ground shall incorporate an earthed armour or metal sheath or both, suitable for use as
a protective conductor, or be of insulated concentric construction. Buried cables shall be marked by cable
covers or a suitable marking tape. Buried conduits and ducts shall be suitably identied. Buried cables,
conduits and ducts shall be at a sufcient depth to avoid being damaged by any reasonably foreseeable
disturbance of the ground.
• Never t bulbs of a higher wattage than those specied on the label, as these may cause overheating and
damage the tting.
• This product has special protection against the ingress of water, and is rated IP44. If the glass or diffuser is
damaged it must be replaced, please consult your retailer. This is the symbol which denotes this requirement:
• If you are in any doubt about your competence please consult a qualied electrician.
• If any modication is made it will invalidate the warranty and may render the product unsafe.

EL-40017-Middleton-WB 20161117
Endon Lighting, LS9 0SE
3. Make a small hole in the grommet and pass incoming mains cable through it, then secure the wall plate to
the wall, ensuring no wiring is trapped, using screws and plugs. Ensure there are rubber washers under the
screw heads.
4. Support your tting and connect the house wiring to the terminal block - see expanded wiring diagram below.
When you are sure of the connections wrap the Terminal Block and overlap the wiring both sides with 2
layers of insulation tape. NOTE: This is a Class I tting and must be earthed.
5. Fit the bulb. NOTE: Never t bulbs of a higher wattage than those specied on the label (as these may
cause overheating and damage the tting).
6. Re-t the diffuser and lamp cover using the screws retained from Step 2. Tighten the screws securely,
ensuring the rubber washers are under the screw heads.
7. Turn on the power and test.
Assembly/ User Instructions Continued