Endon Elan 5lt User manual

Elan 5lt Pendant Light Fitting
Safety Warnings
INSTRUCTION MANUAL
• Thisproductisonlysuitableforconnectiontoa240V~50HzsupplyinaccordancewithcurrentIEEwiringregulations,
andshouldbeinstalledinaccordancewithlocalbuildingregulations.Itisforindooruseonly,andisnotsuitable
forabathroomlocation.
• Beforeinstallingyourlightttingalwaysswitcho󰀨themainssupply,andremovetheappropriatefuseorswitch
o󰀨theappropriatecircuitbreakerbeforecommencinginstallation.Ensurethatnooneelsehasaccessthatwould
enablethesupplytobeinadvertentlyreconnected.
• This is a Class II, Double Insulated product and must not be earthed. Theterminalblocksaresupplied
accordingtorequirementsofthetting.
• Nevertbulbsofahigherwattagethanthosespeciedonthelabel(asthesemaycauseoverheatinganddamage
thetting)
• Thisproductmaycontaindelicateparts–becarefulduringhandlingandmaintenancetoavoidbreakage.
• Ifyouareinanydoubtaboutyourcompetencepleaseconsultaqualiedelectrician.
• Ifanymodicationismadeitwillinvalidatethewarrantyandmayrendertheproductunsafe.
Assembly/ User Instructions
Before you start
Pleasereadtheseinstructionscarefullybeforettingandretainforreference.Checkthepackagingandmakesure
thatyouhavealltherequiredparts.Followeachassemblystepinordertopreventincorrectassembly.Ensurethatthe
productisfullyassembledasillustratedbeforeuse.
Lighttting.
Fixingpack
5xInner&OuterShades&Spacers
The following tools may be required:
Selectionofcrossandatheadscrewdrivers.
Electricdrillandassorteddrillbits.
Wirestrippers.
Theseassemblydiagramsareintendedasaguide–ifindoubtconsultaqualiedelectrician.
Care Information
Allow10minutestocoolbeforereplacing,adjustingorcleaning.
Cleanwithadryclothonly.Donotuseliquidorabrasivecleanersonthisproduct.
1. Decideonthepositionofthelightttingorremoveexistinglighttting.Notethepositionoftheelectricalconnections,
andensurethereisasolidmountingsurface,preferablyawoodenjoistorjoistbridge,tosupporttheweightofthe
lighttting.
2. Ifyouwanttoreducetheoveralllengthofthetting,thiswillbeeasierto
completebeforeattachingtheproducttotheceiling.Toreducethedropof
thispendant,pushthesteelcableupintotheceilingcover.Toincreasethe
droppressbuttonX.Toreducethelengthoftheelectricalex,pulltheex
throughthecablegripYintheceilingcover.Alwaysensuretheweightof
theproductissupportedbythesteelcableandnottheelectricalex.
3. Removethetwosidescrewsandretainforre-use.Usethexingbracket(C)asatemplatetomarkthescrew
holes.Makethescrewholesandsecuretotheceilingwithappropriatexings(A&B).
4. Supportyourttingandconnectthehousewiringtotheterminalblock–seeexpandedwiringdetailsbelow(D).
NOTE:ThisisaClassIIttingandmustNOTbeearthed.
5. Thisproducthas“L”shapedxingholestoalloweasyxingtothexingbracket.Locatethe“L”slots(E)
aroundthesmallscrews(F)onthexingbracket.Rotatetheceilingcovertoattachtheproductto  
thebracket.Tightenthescrewstosecure.Takecarenottotrapanywiring.
90172Elan5ltP20190809
EndonLighting,LS90SE
The light pack contains:
Y
X

Assembly/ User Instructions Continued
90172Elan5ltP20190809
EndonLighting,LS90SE
6. Placetheoutershades(G)overthelampholdersfollowedbythespacers(H)andinnershades(I).Tightenthe
shaderings(J)tosecureinplaceusingthesuppliedtool(K).
7. Fitthebulbs(L).NOTE:Nevertbulbsofahigherwattagethanthosespeciedonthelabel,asthesemay
causeoverheatinganddamagethetting.
8. Turnonthepowerandtest.