Endress+Hauser Proline Promass 80 Technical specifications

Products Solutions Services
KA00023D/06/EN/14.15
71230840
Brief Operating Instructions
Proline Promass 80
Coriolis flowmeter
These Brief Operating Instructions are not intended to replace
the Operating Instructions provided in the scope of supply.
Detailed information about the measuring device is provided in
the Operating Instructions and the additional documentation:
• On the CD-ROM supplied (is not included in the delivery for all
device versions).
• Available for all measuring device versions via:
– Internet: www.endress.com/deviceviewer
– Smartphone/tablet: Endress+Hauser Operations App

Table of contents Proline Promass 80
2Endress+Hauser
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.2 Installation, commissioning and operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
1.4 Safety conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
2 Installation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.1 Transporting to the measuring point . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.2 Installation conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2.3 Post-installation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.4 Post-installation check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13
3.1 Connecting the various housing types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Degree of protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
3.3 Post-connection check . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
4 Hardware settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
4.1 Device address . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
5 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
5.1 Switching on the measuring device . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
5.2 Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
5.3 Navigating within the function matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
5.4 Calling the Commissioning Quick Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
5.5 Software settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5.6 Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23

Proline Promass 80 Safety instructions
Endress+Hauser 3
1 Safety instructions
1.1 Designated use
• The measuring device should only be used to measure the mass flow rate of liquids and gases.
At the same time, the measuring device also measures the density and fluid temperature.
These parameters are then used to calculate other process variables such as volume flow.
• Any use other than that described here compromises the safety of persons and the entire
measuring system and is, therefore, not permitted.
• The manufacturer is not liable for damage caused by improper or non-designated use.
1.2 Installation, commissioning and operation
• The measuring device must only be installed, connected, commissioned and maintained by
qualified and authorized specialists (e.g. electrical technicians) in full compliance with the
instructions in these Brief Operating Instructions, the applicable norms, legal regulations and
certificates (depending on the application).
• The specialists must have read and understood these Brief Operating Instructions and must
follow the instructions they contain. If you are unclear on anything in these Brief Operating
Instructions, you must read the Operating Instructions (on the CD-ROM). The Operating
Instructions provide detailed information on the measuring device.
• The measuring device may only be installed in a de-energized state.
• Repairs may only be performed if a genuine spare parts kit is available and this repair work is
expressly permitted.
• If performing welding work on the piping, the welding unit may not be grounded by means of
the measuring device.
1.3 Operational safety
• The measuring device is designed to meet state-of-the-art safety requirements, has been
tested, and left the factory in a condition in which it is safe to operate. Relevant regulations
and European standards have been observed.
• Observe the technical data on the nameplate!
• The technical staff must ensure that the measuring device has been correctly wired and
grounded as per the wiring diagrams.
• With regard to special fluids, including fluids used for cleaning, Endress+Hauser will be happy
to assist in clarifying the corrosion-resistant properties of wetted materials. However, minor
changes in temperature, concentration or in the degree of contamination in the process may
result in variations in corrosion resistance.
For this reason, Endress+Hauser does not accept any responsibility with regard to the
corrosion resistance of wetted materials in a specific application. The user is responsible for
the choice of suitable wetted materials in the process. A sensor version which allows the
sensor housing be monitored should be used for critical fluids.

Safety instructions Proline Promass 80
4Endress+Hauser
• Hazardous areas
Measuring devices for use in hazardous areas are labeled accordingly on the nameplate.
Relevant national regulations must be observed when operating the device in hazardous
areas. The Ex documentation on the CD-ROM is an integral part of the entire device
documentation.
The installation regulations, connection data and safety instructions provided in the Ex
documentation must be observed. The symbol on the front page indicates the approval and
certification body (0Europe, 2USA, 1Canada). The nameplate also bears the
documentation number of this Ex documentation (XA***D/../..).
• For measuring systems used in SIL 2 applications, the separate manual on functional safety
(on the CD-ROM) must be observed.
• Hygienic applications
Measuring devices for hygienic applications have their own special labeling. Relevant national
regulations must be observed when using these devices.
• Pressure instruments
Measuring devices for use in systems that need to be monitored are labeled accordingly
on the nameplate. Relevant national regulations must be observed when using these devices.
The documentation on the CD-ROM for pressure instruments in systems that need to be
monitored is an integral part of the entire device documentation. The installation regulations,
connection data and safety instructions provided in the Ex documentation must be observed.
• Endress+Hauser will be happy to assist in clarifying any questions on approvals, their
application and implementation.
1.4 Safety conventions
#Warning!
"Warning" indicates an action or procedure which, if not performed correctly, can result in injury
or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution!
“Caution” indicates an action or procedure which, if not performed correctly, can result in
incorrect operation or destruction of the device. Comply strictly with the instructions.
Note! "Note" indicates an action or procedure which, if not performed correctly, can have an
indirect effect on operation or trigger an unexpected response on the part of the device.

Proline Promass 80 Installation
Endress+Hauser 5
2 Installation
2.1 Transporting to the measuring point
• Transport the measuring device to the measuring point in the original packaging.
• The covers or caps fitted on the process connections prevent mechanical damage to the
sensors during transport and storage. For this reason, do not remove the covers or caps until
immediately before installation.
2.2 Installation conditions
For mechanical reasons, and in order to protect the piping, it is advisable to support heavy
sensors.
2.2.1 Dimensions
For the dimensions of the measuring device →see associated Technical Information on the
CD-ROM.
2.2.2 Mounting location
The following mounting locations are recommended:
• Upstream from assemblies such as valves, T-pieces, elbows, etc.
• On the pressure side of pumps (for high system pressure)
• At the lowest point in an ascending pipe (for high system pressure)
A0007408
To transport the unit, use slings slung around the
process connections or use lugs (if available).
#Warning!
Risk of injury! The device can slip.
The center of gravity of the measuring device may be
higher than the holding points of the slings.
Always ensure that the device cannot slip or turn
around its axis.
A0007409
Do not lift measuring devices by the transmitter
housing or the connection housing in the case of the
remote version. Do not use chains as they could
damage the housing.

Installation Proline Promass 80
6Endress+Hauser
The following mounting locations should be avoided:
• At the highest point in a pipe (risk of air accumulating)
• In an open down pipe directly upstream from a free pipe outlet. For ways of using the
measuring device in down pipes, see the related Operating Instructions on the CD-ROM.
2.2.3 Orientation
• The direction of the arrow on the nameplate of the measuring device must match the flow
direction of the fluid.
• The following table lists the possible orientations of the measuring devices:
Vertical Horizontal Horizontal
A0004572 A0004576 A0004576
Transmitter at the side Transmitter at the top Transmitter at the
bottom
Promass A Recommended Possible (m) Possible (m, p)
Promass E Recommended Recommended (n) Recommended (o, p)
Promass F Recommended Recommended (n) Recommended (o, p)
Promass F HT*
Compact version Recommended Not suitable Recommended (o, p)
Promass F HT*
Remote version Recommended Possible (n) Recommended (o, p)
Promass H Recommended Recommended Recommended (p)
Promass I Recommended Recommended Recommended (p)
Promass P Recommended Recommended Recommended (p)
Promass S Recommended Recommended Recommended (p)
*HT = high temperature version for medium temperatures (TM) > 200 °C (> 392 °F)
mDo not install the measuring device in such a way that is suspended without any support or securing unit.
nThis orientation is not suitable for fluids with entrained solids.
oThis orientation is not suitable for outgassing fluids.
pThis orientation is not suitable for low fluid temperatures.

Proline Promass 80 Installation
Endress+Hauser 7
Special installation instructions for Promass A
"Caution!
Risk of measuring pipe fracture if sensor installed incorrectly!
The sensor may not be installed in a pipe as a freely suspended sensor:
• Using the base plate, mount the sensor directly on the floor, the wall or the ceiling.
• Support the sensor on a firmly mounted support base (e.g. angle bracket).
Vertical
We recommend two installation versions when mounting vertically:
• Mounted directly on a wall using the base plate
• Measuring device supported on an angle bracket mounted on the wall
A0018980
Horizontal
We recommend the following installation version when mounting horizontally:
• Measuring device standing on a firm support base
A0018979
2.2.4 Heating
For information on the heating, please see the Operating Instructions on the CD-ROM.
2.2.5 Thermal insulation
For information on the thermal insulation, please see the Operating Instructions on the
CD-ROM.
10 mm
4 x

Installation Proline Promass 80
8Endress+Hauser
2.2.6 Inlet and outlet runs
No inlet and outlet runs are required.
2.2.7 Vibrations
No measures are necessary.

Proline Promass 80 Installation
Endress+Hauser 9
2.3 Post-installation
2.3.1 Turning the transmitter housing
Turning the aluminum field housing
Aluminum field housing for non-Ex area
Aluminum field housing for Zone 1 or Class I Div. 1
Turning the stainless steel field housing
A0007661
A0007540
A0008036
a. Release the setscrew.
b. Turn the transmitter housing gently
clockwise until the stop (end of the
thread).
c. Turn the transmitter
counterclockwise (max. 360°) to the
desired position.
d. Retighten the setscrew.
c
e
f
a
bd
£180° £180°
N
i
c
h
t
u
n
t
e
r
S
p
a
n
n
u
n
g
ö
f
f
n
e
n
K
e
e
p
c
o
v
e
r
t
i
g
h
t
w
h
i
l
e
c
i
r
c
u
i
t
s
a
r
e
a
l
i
v
e
N
e
p
a
s
o
u
v
r i
r
l
’
a
p
p
a
r
e
i
l
s
o
u
s
t
e
n
s
i
o
n
K
e
e
p
c
o
v
e
r
t
i
g
h
t
w
h
i
l
e
c
i
r
c
u
i
t
s
a
r
e
a
l
i
v
e
max. 360°
Nicht-eigensichere
Stromkreise durch
IP40-Abdeckung geschützt
Non-intrinsically safe
circuits Ip40 protected
Boucles de courant
sans sécurité intrinsèque
protégées par Ip40
c
a
b
d
ab
c
d
e
£180° £180°

Installation Proline Promass 80
10 Endress+Hauser
2.3.2 Turning the onsite display
A0007541
a. Press in the side latches on the display module and
remove the module from the cover plate of the
electronics compartment.
b. Turn the display to the desired position (max. 4 × 45° in
both directions) and reset it onto the cover plate of the
electronics compartment.
4 × 45°
a
b

Proline Promass 80 Installation
Endress+Hauser 11
2.3.3 Installing the wall-mount housing
"Caution!
• Make sure that the ambient temperature does not exceed the permitted range.
• Always install the wall-mount housing in such a way that the cable entries point downwards.
Mounted directly on the wall
Pipe mounting
A0007542
1. Connection compartment
2. Securing screws M6 (max. ø 6.5 mm (0.25"); screw head
max. ø 10.5 mm (0.4")
3. Housing bores for securing screws
A0007543
"Caution!
Danger of overheating!
If the device is mounted on a warm pipe, make sure
that the housing temperature does not exceed +60 °C
(+140 °F) which is the maximum temperature permitted.
1
233
90 (3.54)
35 (1.38)
192 (7.56)
81.5 (3.2)
mm (inch)
mm (inch)
Ø 20…70
(Ø 0.79…2.75)
~ ~ 6.1)155 (

Installation Proline Promass 80
12 Endress+Hauser
Panel mounting
A0007544
2.4 Post-installation check
• Is the measuring device damaged (visual inspection)?
• Does the measuring device correspond to the specifications at the measuring point?
• Are the measuring point number and labeling correct (visual inspection)?
• Correct internal diameter and correct surface roughness/quality?
• Has the correct sensor orientation been selected in terms of type, fluid properties, fluid
temperature?
• Does the arrow on the sensor point in the direction of the flow in the pipe?
• Is the measuring device protected against moisture and sunlight?
• Is the measuring device protected against overheating?
245 (9.65)
~110 (~4.33)
210 (8.27)
+0.5 (+0.019)
–0.5 (–0.019)
+0.5 (+0.019)
–0.5 (–0.019)
mm (inch)

Proline Promass 80 Wiring
Endress+Hauser 13
3Wiring
#Warning!
Risk of electric shock! Components carry dangerous voltages.
• Never mount or wire the measuring device while it is connected to the power supply.
• Prior to connecting the power supply, connect the protective ground to the ground terminal
on the housing.
• Route the power supply and signal cables so they are securely seated.
• Seal the cable entries and covers so they are airtight.
"Caution!
Risk of damaging the electronic components!
• Connect the power supply in accordance with the connection data on the nameplate.
• Connect the signal cable in accordance with the connection data in the Operating Instructions
or the Ex documentation on the CD-ROM.
In addition, for the remote version:
"Caution!
Risk of damaging the electronic components!
• Only connect sensors and transmitters with the same serial number
• Observe the cable specifications of the connecting cable →Operating Instructions on the
CD-ROM.
Note! Install the connecting cable securely to prevent movement.
In addition, for measuring devices with fieldbus communication:
"Caution!
Risk of damaging the electronic components!
• Observe the cable specification of the fieldbus cable →Operating Instructions on the CD-ROM.
• Keep the stripped and twisted lengths of cable shield as short as possible.
• Screen and ground the signal lines →Operating Instructions on the CD-ROM.
• When using in systems without potential matching →Operating Instructions on the CD-ROM.
In addition, for Ex-certified measuring devices:
#Warning!
When wiring Ex-certified measuring devices, all the safety instructions, wiring diagrams,
technical information etc. of the related Ex documentation must be observed →
Ex documentation on the CD-ROM.

Wiring Proline Promass 80
14 Endress+Hauser
3.1 Connecting the various housing types
Wire the unit using the terminal assignment diagram inside the cover.
3.1.1 Compact version
3.1.2 Remote version (transmitter): non-Ex Zone, Ex Zone 2, Class I Div. 2
3.1.3 Remote version (transmitter): Ex Zone 1, Class I Div. 1
3.1.4 Remote version (sensor)
A0007545
Transmitter connection:
1
2
3
4
Connection diagram inside the
connection compartment cover
Power supply cable
Signal cable or fieldbus cable
Optional
A0007546
Transmitter connection:
1
2
3
4
Connection diagram inside the
connection compartment cover
Power supply cable
Signal cable
Fieldbus cable
Connecting cable connection:
5 Sensor/transmitter connecting cable
A0007547
Transmitter connection:
1
2
3
4
Connection diagram inside the
connection compartment cover
Power supply cable
Signal cable or fieldbus cable
Optional
Connecting cable connection:
5 Sensor/transmitter connecting cable
A0008037
Transmitter connection:
1 Connection diagram inside the connection compartment cover
Connecting cable connection:
5 Sensor/transmitter connecting cable
1
2
3
4
231
4 5
c
i
r
c
u
i
t
s
a
r
e
a
l
i
v
e
s
o
u
s
t
e
n
s
i
o
n
c
i
r
c
u
i
t
s
a
r
e
a
l
i
v
e
N
i
c
h
t
u
n
t
e
r
S
p
a
n
n
u
n
g
ö
f
f
n
e
n
K
e
e
p
c
o
v
e
r
t
i
g
h
t
w
h
i
l
e
N
e
p
a
s
o
u
v
r
i
r
l
’
a
p
p
a
r
e
i
l
K
e
e
p
c
o
v
e
r
t
i
g
h
t
w
h
i
l
e
c
i
r
c
u
i
t
s
a
r
e
a
l
i
v
e
2
3
5
1
1
4
51

Proline Promass 80 Wiring
Endress+Hauser 15
3.2 Degree of protection
The devices meet all the requirements for IP 67.
After mounting in the field or service work, the following points have to be observed to ensure
that IP 67 protection is retained:
• Install the measuring device in such a way that the cable entries do not point upwards.
• Do not remove the seal from the cable entry.
• Remove all unused cable entries and plug them with suitable drain plugs.
3.3 Post-connection check
• Are cables or the device damaged (visual inspection)?
• Does the supply voltage match the specifications on the nameplate?
• Are the power supply and signal cables correctly connected?
• Do the cables used comply with the necessary specifications?
• Do the mounted cables have adequate strain relief and are they routed securely?
• Is the cable type route completely isolated? Without loops and crossovers?
• Are all screw terminals correctly tightened?
• Are all the cable entries installed, correctly tightened and properly sealed?
• Cable routed as a "water trap" in loops?
• Are all housing covers installed and correctly tightened?
In addition, for measuring devices with fieldbus communication:
• Are all the connecting components (T-boxes, junction boxes, connectors, etc.) connected with
each other correctly?
• Has each fieldbus segment been terminated at both ends with a bus terminator?
• Has the max. length of the fieldbus cable been observed in accordance with the specifications?
• Has the max. length of the spurs been observed in accordance with the specifications?
• Is the fieldbus cable fully shielded and correctly grounded?
A0007549
Tighten the cable entries correctly.
A0007550
The cables must loop down before they enter the cable
entries (“water trap”).

Hardware settings Proline Promass 80
16 Endress+Hauser
4 Hardware settings
This section only deals with the hardware settings needed for commissioning.
All other settings (e.g. output configuration, write protection, etc.) are described in the
associated Operating Instructions on the CD-ROM.
Note! No hardware settings are needed for measuring devices with HART-type communication.
4.1 Device address
Has to be set for measuring devices with the following communication methods:
•PROFIBUSPA
The device address can be configured via:
• Miniature switches →see description below
• Local operation →see section Software settings →22
Addressing via miniature switches
#Warning!
Risk of electric shock! Risk of damaging the electronic components!
• All the safety instructions for the measuring device must be observed and all the warnings
heeded →22.
• Use a workspace, working environment and tools purposely designed for electrostatically
sensitive devices.
A0007551
a. Switch off the power supply before opening the device.
b. Loosen the cheese head screw of the securing clamp
with an Allen key (3 mm).
c. Unscrew cover of the electronics compartment from the
transmitter housing.
d. Loosen the securing screws of the display module and
remove the onsite display (if present).
e. Set the position of the miniature switches on the I/O
board using a sharp pointed object.
f. Installation is the reverse of the removal procedure.
1
2
3
4
W
E
N
O
1
2
3
4
W
E
N
O
1
2
3
4
W
E
N
O
1
2
3
4
W
E
N
O
1
2
3
4
W
E
N
O
1
2
3
4
W
E
N
O
a
b
c
d

Proline Promass 80 Hardware settings
Endress+Hauser 17
PROFIBUS
A0007552
Device address range: 0 to 126
Factory setting: 126
a. Miniature switches for the device address
(example shown:
1+16+32 = device address 49)
b. Miniature switches for the address mode
(method of addressing):
– OFF (factory setting) = software addressing via local
operation/operating program
– ON = hardware addressing via miniature switches
c. Miniature switch not assigned.
161
3
322
4
643
4
1
2
b
OFF ON
11
22
43
84 a
OFF ON
c
161
3
322
4
643
4
1
2
b
OFF ON
11
22
43
84 a
OFF ON
c
DP PA

Commissioning Proline Promass 80
18 Endress+Hauser
5 Commissioning
5.1 Switching on the measuring device
On completion of the installation (successful post-installation check), wiring (successful
post-connection check) and after making the necessary hardware settings, where applicable,
the permitted power supply (see nameplate) can be switched on for the measuring device.
When the power supply is switched on, the measuring device performs a number of power-up
checks and device self-checks. As this procedure progresses the following messages can appear
on the onsite display:
The measuring device starts operating as soon as the startup procedure is complete.
Various measured values and/or status variables appear on the display.
Note! If an error occurs during startup, this is indicated by an error message.
The error messages that occur most frequently when a measuring device is commissioned
are described in the Troubleshooting section →23.
Display examples:
PROMASS 80
STARTING . . .
Start-up message
Æ
DEVICE SOFTWARE
V XX.XX.XX
Displays the current software
Æ
SYSTEM OK
→OPERATION
Beginning of operation

Proline Promass 80 Commissioning
Endress+Hauser 19
5.2 Operation
5.2.1 Display elements
5.2.2 Operating elements
5.2.3 Displaying error messages
A0007557
Display lines/fields
1. Main line for primary measured values
2. Additional line for additional measured variables/status
variables
3. Current measured values
4. Engineering units/time units
A0007559
Operating keys
1. (–) Minus key for entering, selecting
2. (+) Plus key for entering, selecting
3. Enter key for calling the function matrix, saving
When the +/– keys are pressed simultaneously (Esc):
• Exit the function matrix step-by-step:
• > 3 sec. = cancel data input and
return to the measured value display
A0007561
1. Type of error:
P = Process error, S = System error
2. Error message type:
$= Fault message, ! = Notice message
3. Error number
4. Duration of the last error that occurred:
Hours: Minutes: Seconds
5. Error designation
• List of the most common error messages during
commissioning →23
• List of all error messages, see associated Operating
Instructions on the CD-ROM
+48.25 xx/yy
+3702.6 x
1
2
34
Esc
E
+
-
1 2 3
XXXXXXXXXX
#000 00:00:05
P
34
2
1 5

Commissioning Proline Promass 80
20 Endress+Hauser
5.3 Navigating within the function matrix
A0007562
1. F →Enter the function matrix (starting with measured value display)
2. P →Select the group (e.g. OPERATION)
F →Confirm selection
3. N→Select function (e.g. LANGUAGE)
4. P →Enter code 80 (only for the first time you access the function matrix)
F →Confirm entry
P →Change function/selection (e.g. ENGLISH)
F →Confirm selection
5. Q →Return to measured value display step by step
6. Q > 3 s →Return immediately to measured value display
Esc
E
+
-
>3s
E
+
Esc
–+
Esc
–
m
o
n
E
E
–
+
E
+
–
E E E E
p
q
qr