Endress+Hauser Proline Promass 80 User manual

BA057D/06/en/10.03
50098468
Valid as of software version:
V 1.06.XX (amplifier)
V 1.03.XX (communication)
PROline promass 80
Coriolis Mass Flow
Measuring System
Operating Instructions

Brief operating instructions PROline Promass 80
2Endress+Hauser
Brief operating instructions
These brief operating instructions show you how to configure your measuring device
quickly and easily:
!Note:
Always start trouble-shooting with the checklist on Page 61, if faults occur after
commissioning or during operation. The routine takes you directly to the cause of the
problem and the appropriate remedial measures.
Safety instructions Page 7
▼
Installation Page 13
▼
Wiring Page 23
▼
Display and operating elements Page 31 ff.
▼
Commissioning with “QUICK SETUP” Page 50
You can commission your measuring device quickly and easily, using the special
“Quick Setup” menu. It enables you to configure important basic functions using
the local display, for example display language, measured variables, units of
measures, type of signal, etc.
The following functions can be configured separately as necessary:
– Zero point adjustment
– Density calibration
– Configuration of the current output (active/passive)
▼
Customer specific configuration Page 52 ff.
Complex measuring operations necessitate additional functions that you can
configure as necessary with the aid of the function matrix, and customise to suit
your process parameters.
!Note:
All functions are described in detail, as is the function matrix itself, in the
“Description of Device Functions” manual, which is a separate part of these
Operating Instructions.

PROline Promass 80 QUICK SETUP “Commissioning”
Endress+Hauser 3
QUICK SETUP “Commissioning”
!Note:
More detailed information on running Quick Setup menus, especially for devices without
a local display, can be found on Page 50 ff.
Information on the points numbered in the Quick Setup can be found on the following
page.
+
++
EE
Esc
E
- +
➄
Ye s
Ye s
Ye s
No
No
No
Mass flow
Current output 1
Volume flow Density
Frequency/Pulse output
Selection System Units
Selection output type
Configuration another unit ?
Configuration another output ?
Automatically configuration display ?
Temperature Quit
Quit
Unit
Mass flow
Assign
Current
Current span
Value
0/4 mA
Value
20 mA
Time constant
Time constant
Failsafe mode
Failsafe mode
Failsafe mode
Assign
Frequency
End value
frequency
Value
F Low
Value
F High
Output signal
Assign
Pulse
Pulse value
Pulse width
Output signal
Unit
flowVolume
Unit
Density
Operation mode
Unit
Temperature
Measuring
Mode
Unit
Totalizer
Unit
Totalizer
Frequency Pulse
Automatically
parameterization
of the display
Language
Pre-setting
Quick Setup
HOME-POSITION
Quick Setup
Commission
Assign
Current
Current span
Value
0/4 mA
Value
20 mA
Time constant
Failsafe mode
Current output 2
➀
➁
➂
➃
Corr. Vol. flow
Unit
Corr. Vol. flow
Unit
Ref. Density
Fix
Ref. Density
F06-80xxxxxx-19-xx-xx-en-000

QUICK SETUP “Commissioning” PROline Promass 80
4Endress+Hauser
!•The display returns to the cell QUICK SETUP COMMISSION if you press the ESC key
combination during parameter interrogation. The stored parameters remain valid.
•The “Commissioning” Quick Setup must be carried out before one of the Quick Setups
explained below is run.
•➀Only units not yet configured in the current Setup are offered for selection in each
cycle. The unit for mass, volume and corrected volume is derived from the
corresponding flow unit.
•➁The “YES” option remains visible until all the units have been configured.
“NO” is the only option displayed when no further units are available.
•➂Only the outputs not yet configured in the current Setup are offered for selection in
each cycle.
•➃The “YES” option remains visible until all the outputs have been parameterized.
“NO” is the only option displayed when no further outputs are available.
•➄ The “automatic parameterization of the display” option contains the following
basic
settings/factory settings:
YES: line 1 = mass flow; line 2 = totalizer 1
NO: The existing (selected) settings remain.

PROline Promass 80 Table of contents
Endress+Hauser 5
Table of contents
1 Safety instructions . . . . . . . . . . . . . . . . . 7
1.1 Designated use . . . . . . . . . . . . . . . . . . . . . . . . 7
1.2 Installation, commissioning and operation . . . 7
1.3 Operational safety . . . . . . . . . . . . . . . . . . . . . . 7
1.4 Return . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
1.5 Notes on safety conventions and icons . . . . . . 8
2 Identification . . . . . . . . . . . . . . . . . . . . . . 9
2.1 Device designation . . . . . . . . . . . . . . . . . . . . . 9
2.1.1 Nameplate of the transmitter . . . . . . . 9
2.1.2 Nameplate of the sensor. . . . . . . . . . 10
2.2 CE mark, declaration of conformity . . . . . . . . 10
2.3 Registered trademarks . . . . . . . . . . . . . . . . . 11
3 Installation . . . . . . . . . . . . . . . . . . . . . . . . 13
3.1 Incoming acceptance, transport and storage 13
3.1.1 Incoming acceptance . . . . . . . . . . . 13
3.1.2 Transport . . . . . . . . . . . . . . . . . . . . . 13
3.1.3 Storage . . . . . . . . . . . . . . . . . . . . . . . 14
3.2 Installation conditions . . . . . . . . . . . . . . . . . . 14
3.2.1 Dimensions . . . . . . . . . . . . . . . . . . . 14
3.2.2 Mounting location . . . . . . . . . . . . . . . 14
3.2.3 Orientation. . . . . . . . . . . . . . . . . . . . . 16
3.2.4 Heating . . . . . . . . . . . . . . . . . . . . . . . 18
3.2.5 Thermal insulation . . . . . . . . . . . . . . 19
3.2.6 Inlet and outlet runs . . . . . . . . . . . . . 19
3.2.7 Vibrations . . . . . . . . . . . . . . . . . . . . . 19
3.2.8 Limiting flow . . . . . . . . . . . . . . . . . . . 19
3.3 Installation instructions . . . . . . . . . . . . . . . . . 20
3.3.1 Turning the transmitter housing . . . . 20
3.3.2 Installing the wall-mount transmitter
housing . . . . . . . . . . . . . . . . . . . . . . . 21
3.3.3 Turning the local display. . . . . . . . . . 22
3.4 Post installation check . . . . . . . . . . . . . . . . . . 22
4 Wiring . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
4.1 Connecting the remote version . . . . . . . . . . . 23
4.1.1 Connecting the sensor . . . . . . . . . . . 23
4.1.2 Cable specifications . . . . . . . . . . . . . 24
4.2 Connecting the measuring unit . . . . . . . . . . . 25
4.2.1 Connecting the transmitter . . . . . . . . 25
4.2.2 Terminal assignment. . . . . . . . . . . . . 27
4.2.3 HART connection . . . . . . . . . . . . . . . 28
4.3 Degree of protection . . . . . . . . . . . . . . . . . . . 29
4.4 Post connection check . . . . . . . . . . . . . . . . . 30
5 Operation . . . . . . . . . . . . . . . . . . . . . . . . . 31
5.1 Display and operating elements . . . . . . . . . . 31
5.2 Brief operating instructions to the function
matrix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
5.2.1 General notes . . . . . . . . . . . . . . . . . . 33
5.2.2 Enabling the programming mode . . 33
5.2.3 Disabling the programming mode . . 33
5.3 Display of error messages . . . . . . . . . . . . . . . 34
5.4 Communication . . . . . . . . . . . . . . . . . . . . . . . . 35
5.4.1 Operating options . . . . . . . . . . . . . . . 35
5.4.2 Device and process variables . . . . . 36
5.4.3 Universal / Common practice HART
commands . . . . . . . . . . . . . . . . . . . . . 37
5.4.4 Device status / Error messages . . . . . 43
6 Commissioning . . . . . . . . . . . . . . . . . . . 49
6.1 Function check . . . . . . . . . . . . . . . . . . . . . . . . 49
6.2 Commissioning . . . . . . . . . . . . . . . . . . . . . . . . 49
6.2.1 Switching on the measuring device . 49
6.2.2 Quick Setup “Commissioning”. . . . . . 50
6.2.3 Zero point adjustment . . . . . . . . . . . . 52
6.2.4 Density adjustment . . . . . . . . . . . . . . 54
6.2.5 Current output 1: active/passive . . . . 55
6.2.6 Current outputs 2: active/passive . . . 56
6.2.7 Purge and pressure monitoring
connections . . . . . . . . . . . . . . . . . . . . 57
7 Maintenance . . . . . . . . . . . . . . . . . . . . . . 58
8 Accessories . . . . . . . . . . . . . . . . . . . . . . . 59
9 Trouble-shooting . . . . . . . . . . . . . . . . . 61
9.1 Trouble-shooting instructions . . . . . . . . . . . . . 61
9.2 System error messages . . . . . . . . . . . . . . . . . 62
9.3 Process error messages . . . . . . . . . . . . . . . . . 67
9.4 Process errors without messages . . . . . . . . . . 69
9.5 Response of outputs to errors . . . . . . . . . . . . 70
9.6 Spare parts . . . . . . . . . . . . . . . . . . . . . . . . . . . 72
9.7 Removing and installing printed circuit
boards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 73
9.8 Replacing the device fuse . . . . . . . . . . . . . . . 77
9.9 Software history . . . . . . . . . . . . . . . . . . . . . . . 78
10 Technical data . . . . . . . . . . . . . . . . . . . . 81
10.1 Technical data at a glance . . . . . . . . . . . . . . . 81
10.1.1 Applications . . . . . . . . . . . . . . . . . . . 81
10.1.2 Function and system design . . . . . . . 81
10.1.3 Input . . . . . . . . . . . . . . . . . . . . . . . . . 81
10.1.4 Output . . . . . . . . . . . . . . . . . . . . . . . . 83
10.1.5 Auxiliary energy . . . . . . . . . . . . . . . . 83
10.1.6 Performance characteristics . . . . . . . 84
10.1.7 Operating conditions . . . . . . . . . . . . . 88
10.1.8 Mechanical construction . . . . . . . . . . 97
10.1.9 Human interface. . . . . . . . . . . . . . . . 100
10.1.10 Certificates and approvals . . . . . . . 100
10.1.11 Ordering information . . . . . . . . . . . . 100
10.1.12 Accessories . . . . . . . . . . . . . . . . . . 101
10.1.13 Documentation . . . . . . . . . . . . . . . . 101
10.2 Dimensions: Wall-mount housing . . . . . . . . . 102
10.3 Dimensions: Stainless steel field housing . . . 102

Table of contents PROline Promass 80
6Endress+Hauser
10.4 Dimensions: Remote version
(Promass F, M, A, H, I) . . . . . . . . . . . . . . . . . 103
10.5 Dimensions: Remote version (Promass E) . . 103
10.6 Dimensions: Remote version for heating . . . 103
10.7 Dimensions: High-temperature version
(compact) . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
10.8 Dimensions: High-temperature version
(remote) . . . . . . . . . . . . . . . . . . . . . . . . . . . . 104
10.9 Dimensions: Promass F . . . . . . . . . . . . . . . . 105
10.10 Dimensions: Promass M . . . . . . . . . . . . . . . 115
10.11 Dimensions: Promass E . . . . . . . . . . . . . . . . 129
10.12 Dimensions: Promass A . . . . . . . . . . . . . . . . 138
10.13 Dimensions: Promass H . . . . . . . . . . . . . . . . 144
10.14 Dimensions: Promass I . . . . . . . . . . . . . . . . 146
Index . . . . . . . . . . . . . . . . . . . . . . . . . . . . 157

PROline Promass 80 1 Safety instructions
Endress+Hauser 7
1 Safety instructions
1.1 Designated use
The measuring device described in these Operating Instructions is to be used only for
measuring the mass flow rate of fluids and gases. At the same time, the system also
measures fluid density and fluid temperature. These parameters are then used to
calculate other variables such as volume flow. Fluids with widely differing properties can
be measured, for example:
•Chocolate, condensed milk, liquid sugar
•Oils, fats
•Acids, alkalis, lacquers, paints, solvents and cleaning agents
•Pharmaceuticals, catalysts, inhibitors
•Suspensions
•Gases, liquefied gases, etc.
Resulting from incorrect use or from use other than that designated, the operational
safety of the measuring devices can be suspended. The manufacturer accepts no
liability for damages being produced from this.
1.2 Installation, commissioning and operation
Note the following points:
•Installation, connection to the electricity supply, commissioning and maintenance of
the device must be carried out by trained, qualified specialists authorised to perform
such work by the facility's owner operator. The specialist must have read and
understood these Operating Instructions and must follow the instructions it contains.
•The device must be operated by persons authorised and trained by the facility's
owner-operator. Strict compliance with the instructions in the Operating Instructions is
mandatory.
•Endress+Hauser will be happy to assist in clarifying the chemical resistance
properties of parts wetted by special fluids, including fluids used for cleaning.
However the user is responsible for the choice of fluid wetted materials for their in-
process resistance to corrosion. The manufacturer refuses to accept liability.
•The installer must ensure that the measuring system is correctly wired in accordance
with the wiring diagrams. The transmitter must be grounded, unless the power supply
is galvanically insulated.
•Invariably, local regulations governing the opening and repair of electrical devices
apply.
1.3 Operational safety
Note the following points:
•Measuring systems for use in hazardous environments are accompanied by separate
“Ex documentation”, which is an integral part of these Operating Instructions. Strict
compliance with the installation instructions and ratings as stated in this
supplementary documentation is mandatory. The symbol on the front of this
supplementary Ex documentation indicates the approval and the certification body
(0Europe, 2USA, 1Canada).
•The measuring device complies with the general safety requirements in accordance
with EN 61010, the EMC requirements of EN 61326/A1 and NAMUR recommendation
NE 21/43.
•The manufacturer reserves the right to modify technical data without prior notice. Your
E+H distributor will supply you with current information and updates to these
Operating Instructions.

1 Safety instructions PROline Promass 80
8Endress+Hauser
1.4 Return
The following procedures must be carried out before a flowmeter requiring repair or
calibration, for example, is returned to Endress+Hauser:
•Always enclose a duly completed “Declaration of contamination” form. Only then can
Endress+Hauser transport, examine and repair a returned device.
•Enclose special handling instructions if necessary, for example a safety data sheet as
per EN 91/155/EEC.
•Remove all residues. Pay special attention to the grooves for seals and crevices which
could contain residues. This is particularly important if the substance is hazardous to
health, e.g. flammable, toxic, caustic, carcinogenic, etc.
With Promass A and Promass M the threaded process connections must first be
removed from the sensor and then cleaned.
!Note:
You will find a preprinted “Declaration of contamination” form at the back of this manual.
#Warning:
•Do not return a measuring device if you are not absolutely certain that all traces of
hazardous substances have been removed, e.g. substances which have penetrated
crevices or diffused through plastic.
•Costs incurred for waste disposal and injury (burns, etc.) due to inadequate cleaning
will be charged to the owner operator.
1.5 Notes on safety conventions and icons
The devices are designed to meet state-of-the-art safety requirements, have been
tested, and left the factory in a condition in which they are safe to operate. The devices
comply with the applicable standards and regulations in accordance with EN 61010
“Protection Measures for Electrical Equipment for Measurement, Control, Regulation
and Laboratory Procedures”. They can, however, be a source of danger if used
incorrectly or for other than the designated use.
Consequently, always pay particular attention to the safety instructions indicated in
these Operating Instructions by the following icons:
#Warning:
“Warning” indicates an action or procedure which, if not performed correctly, can result
in injury or a safety hazard. Comply strictly with the instructions and proceed with care.
"Caution:
“Caution” indicates an action or procedure which, if not performed correctly, can result
in incorrect operation or destruction of the device. Comply strictly with the instructions.
!Note:
“Note” indicates an action or procedure which, if not performed correctly, can have an
indirect effect on operation or trigger an unexpected response on the part of the device.

PROline Promass 80 2 Identification
Endress+Hauser 9
2 Identification
2.1 Device designation
The “Promass 80” flow measuring system consists of the following components:
•Promass 80 transmitter
•Promass F, Promass M, Promass E, Promass A, Promass H or Promass I sensor
In the compact version, transmitter and sensor form a single mechanical unit; in the
remote version they are installed separately.
2.1.1 Nameplate of the transmitter
Fig. 1: Nameplate specifications for the “Promass 80” transmitter (example)
1 Ordering code/serial number: See the specifications on the order confirmation for the meanings of the
individual letters and digits.
2 Power supply / frequency: 20...55 V AC /16...62 V DC / 50...60 Hz
Power consumption: 15 VA / 15 W
3 Available inputs / outputs:
I-OUT (HART): with current output (HART)
f-OUT: with pulse/frequency output
STATUS-IN: with status input (auxiliary input)
STATUS-OUT: with status output (switching output)
4 Reserved for information on special products
5 Ambient temperature range
6 Degree of protection
PROMASS
ENDRESS+HAUSER
Order Code:
80
Ser.No.:
TAG No.:
20-55VAC/16-62VDC
50-60Hz 15VA/15W
IP67/NEMA/Type4X80F25-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
–20°C (–4°F) < Tamb < +60°C (+140°F)
i
1
6
5
2
3
4
Pat. US 5,479,007
Pat. US 4,768,384
Pat. UK 261 435
5,648,616
4,801,897
EP 262 573 EP 618 680
I-OUT (HART), f-OUT
STATUS-IN, STATUS-OUT
F06-80xxxxxx-18-06-xx-xx-000

2 Identification PROline Promass 80
10 Endress+Hauser
2.1.2 Nameplate of the sensor
Fig. 2: Nameplate specifications for the “Promass F” sensor (example)
1 Ordering code/Serial number: See the specifications on the order confirmation for the meanings of the
individual letters and digits.
2 Calibration factor: 2.510; zero point: –11
3 Nominal diameter device: DN 25 / 1"
4 Nominal diameter flange: DN 25 / 1"
Pressure rating: EN (DIN) PN 100 bar
5 Material of measuring tubes: Stainless steel 1.4539/904L
6 TMmax +200 °C / +392 °F (max. fluid temperature)
7 Pressure range of secondary containment: max. 40 bar (600 psi)
8 Accuracy of density measurement: ± 0.001 g/cc
9 Additional information (examples):
– With 5-point calibration
– With 3.1 B certification for fluid wetted materials
10 Reserved for information on special products
11 Ambient temperature range
12 Degree of protection
13 Flow direction
14 Reserved for additional information on device version (approvals, certificates)
2.2 CE mark, declaration of conformity
The devices are designed in accordance with good engineering practice to meet state-
of-the-art safety requirements, have been tested, and left the factory in a condition in
which they are safe to operate. The devices comply with the applicable standards and
regulations in accordance with EN 61010 “Protection Measures for Electrical Equipment
for Measurement, Control, Regulation and Laboratory Procedures” and with the EMC
requirements of EN 61326/A1.
The measuring system described in these Operating Instructions thus complies with the
statutory requirements of the EC Directives. Endress+Hauser confirms successful
testing of the device by affixing to it the CE mark.
1
2
4
5
6
7
8
9
11
12
13
200°C / 392°F
40 bar / 600 psi Container
2.5100 / -11
DN25 / 1" EN (DIN) PN100
1.4539 / 904L
5P-CAL, 3.1B
Density cal.:
-20°C (-4°F)<Tamb<+60°C (+140°F)
PROMASS F
ENDRESS+HAUSER
Pat. US 5,796,011
Materials:
TMmax.:
Order Code:
K-factor:
TAG No.:
Ser.No.:
IP67/NEMA/Type4X
+/-0.001g/cc
XXF25-XXXXXXXXXXXX
12345678901
ABCDEFGHJKLMNPQRST
i
14
DN25 / 1"
Size : 3
10
F06-8xFxxxxx-18-05-xx-xx-000

PROline Promass 80 2 Identification
Endress+Hauser 11
2.3 Registered trademarks
KALREZ ®, VITON ®
Registered trademarks of E.I. Du Pont de Nemours & Co., Wilmington, USA
TRI-CLAMP ®
Registered trademark of Ladish & Co., Inc., Kenosha, USA
SWAGELOK ®
Registered trademark of Swagelok & Co., Solon, USA
HART ®
Registered trademark of HART Communication Foundation, Austin, USA
S-DAT™, FieldTool™, FieldCheck™, Applicator™
Registered or registration-pending trademarks of Endress+Hauser Flowtec AG,
Reinach, CH

2 Identification PROline Promass 80
12 Endress+Hauser

PROline Promass 80 3 Installation
Endress+Hauser 13
3 Installation
3.1 Incoming acceptance, transport and storage
3.1.1 Incoming acceptance
On receipt of the goods, check the following points:
•Check the packaging and the contents for damage.
•Check the shipment, make sure nothing is missing and that the scope of supply
matches your order.
3.1.2 Transport
The following instructions apply to unpacking and to transporting the device to its final
location:
•Transport the devices in the containers in which they are delivered.
•The covers or caps fitted to the process connections prevent mechanical damage to
the sealing faces and the ingress of foreign matter to the measuring tube during
transportation and storage. Consequently, do not remove these covers or caps until
immediately before installation.
•Do not lift measuring devices of nominal diameters DN 40...150 by the transmitter
housing or the connection housing in the case of the remote version (Fig. 3). Use
webbing slings slung round the two process connections. Do not use chains, as they
could damage the housing.
•In the case of the Promass M / DN 80 sensor, use only the lifting eyes on the flanges
to lift the assembly.
#Warning:
Risk of injury if the measuring device slips. The center of gravity of the assembled
measuring device might be higher than the points around which the slings are slung.
At all times, therefore, make sure that the device does not unexpectedly turn around its
axis or slip.
Fig. 3: Instructions for transporting sensors with DN 40...150
F06-xxxxxxxx-22-00-00-xx-000

3 Installation PROline Promass 80
14 Endress+Hauser
3.1.3 Storage
Note the following points:
•Pack the measuring device in such a way as to protect it reliably against impact for
storage (and transportation). The original packaging provides optimum protection.
•The permissible storage temperature is –40...+80 °C (preferably +20 °C).
•Do not remove the protective covers or caps on the process connections until you are
ready to install the device.
•The measuring device must be protected against direct sunlight during storage in
order to avoid unacceptably high surface temperatures.
3.2 Installation conditions
Note the following points:
•No special measures such as supports are necessary. External forces are absorbed
by the construction of the instrument, for example the secondary containment.
•The high oscillation frequency of the measuring tubes ensures that the correct
operation of the measuring system is not influenced by pipe vibrations.
•No special precautions need to be taken for fittings which create turbulence (valves,
elbows, T-pieces, etc.), as long as no cavitation occurs.
•For mechanical reasons and in order to protect the pipe, it is advisable to support
heavy sensors.
3.2.1 Dimensions
Dimensions and the fitting lengths of the transmitter and sensor are on Page 102 ff.
3.2.2 Mounting location
Entrained gas bubbles in the measuring tube can result in an increase in measuring
errors. Avoid the following locations:
•Highest point of a pipeline. Risk of air accumulating.
•Directly upstream of a free pipe outlet in a vertical pipeline.
Fig. 4: Mounting location
F06-xxxxxxxx-11-00-00-xx-004

PROline Promass 80 3 Installation
Endress+Hauser 15
The proposed configuration in Fig. 5, however, permits installation in a vertical pipeline.
Pipe restrictors or the use of an orifice with a smaller cross-section than the nominal
diameter prevent the sensor from running empty during measurement.
Fig. 5: Installation in a vertical pipe (e.g. for batching applications)
1 Supply tank
2 Sensor
3 Orifice, pipe restrictions (see Table)
4Valve
5 Batching tank
System pressure
It is important to ensure that cavitation does not occur, because it would influence the
oscillation of the measuring tube. No special measures need to be taken for fluids which
have properties similar to water under normal conditions.
In the case of liquids with a low boiling point (hydrocarbons, solvents, liquefied gases)
or in suction lines, it is important to ensure that pressure does not drop below the vapour
pressure and that the liquid does not start to boil. It is also important to ensure that the
gases that occur naturally in many liquids do not outgas. Such effects can be prevented
when system pressure is sufficiently high.
Consequently, it is generally best to install the sensor:
•downstream from pumps (no danger of vacuum),
•at the lowest point in a vertical pipe.
Promass F, M, E / DN 8 1525405080
1) 100 2) 150 2)
Ø orifice / pipe restriction 6 mm 10 mm 14 mm 22 mm 28 mm 50 mm 65 mm 90 mm
1) Promass F, M only
2) Promass F only
Promass A / DN 124
Ø orifice / pipe restriction 0.8 mm 1.5 mm 3.0 mm
Promass H, I / DN 8 15 15 1) 25 25 1) 40 40 1) 50
Ø orifice / pipe restriction 6 mm 10 mm 15 mm 14 mm 24 mm 22 mm 35 mm 28 mm
1) DN 15, 25, 40 “FB” = Full bore versions of Promass I
F06-xxxxxxxx-11-00-00-xx-002

3 Installation PROline Promass 80
16 Endress+Hauser
3.2.3 Orientation
Make sure that the direction of the arrow on the nameplate of the sensor matches the
direction of flow (direction in which the fluid flows through the pipe).
Orientation Promass A
Vertical:
Recommended orientation with upward direction of flow. When fluid is not flowing,
entrained solids will sink down and gases will rise away from the measuring tube.
The measuring tubes can be completely drained and protected against solids build-up.
Horizontal:
When installation is correct the transmitter housing is above or below the pipe. This
arrangement means that no gas or solid deposits can accumulate in the curved
measuring tube (single-tube system).
Do not install the sensor in such a way that it is suspended in the pipe, in other words
without support or attachment. This is to avoid excessive strain at the process
connection. The base plate of the sensor housing is designed for mounting on a
tabletop, wall or post.
Fig. 6: Vertical and horizontal orientation (Promass A)
F06-xxxxxxxx-11-00-00-xx-005

PROline Promass 80 3 Installation
Endress+Hauser 17
Orientation Promass F, M, E, H, I
Make sure that the direction of the arrow on the nameplate of the sensor matches the
direction of flow (direction in which the fluid flows through the pipe).
Vertical:
Recommended orientation with upward direction of flow (View V). When fluid is not flow-
ing, entrained solids will sink down and gases will rise away from the measuring tube.
The measuring tubes can be completely drained and protected against solids build-up.
Horizontal (Promass F, M, E):
The measuring tubes of Promass F, M and E must be horizontal and beside each other.
When installation is correct the transmitter housing is above or below the pipe (View
H1/H2). Always avoid having the transmitter housing in the same horizontal plane as the
pipe.
Horizontal (Promass H, I):
Promass H and Promass I can be installed in any orientation in a horizontal pipe run.
✓✓ = Recommended orientation
✓= Orientation recommended in certain situations
✗= Impermissible orientation
Promass F, M, E, H, I Standard, kompakt Promass F, M, E, H, I Standard, getrennt Promass F Hochtemperatur, kompakt Promass F Hochtemperatur, getrennt
Vertikale Einbaulage (Abb. V)
✓✓ ✓✓ ✓✓ ✓✓
Horizontale Einbaulage (Abb. H1)
Messumformerkopf oben
✓✓ ✓✓ ✗
(TM= >200 °C)
➀
✓
(TM= >200 °C)
➀
Horizontale Einbaulage (Abb. H2)
Messumformerkopf unten
✓✓
➁
✓✓
➁
✓✓
➁
✓✓
➁

3 Installation PROline Promass 80
18 Endress+Hauser
In order to ensure that the maximum permissible ambient temperature for the transmitter
(–20...+60 °C, optional –40...+60 °C) is not exceeded, we recommend the following ori-
entations:
➀ = For fluids with very high temperatures (> 200 °C), we recommend the horizontal
orientation with the transmitter head pointing downwards (Fig. H2) or the vertical orien-
tation (Fig. V)
➁= For fluids with low temperatures, we recommend the horizontal orientation with the
transmitter head pointing upwards (Fig. H1) or the vertical orientation (Fig. V).
Special installation instructions for Promass F, E and H
"Caution:
The two measuring tubes of Promass F and Promass E and the one of Promass H are
slightly curved. The position of the sensor, therefore, has to be matched to the fluid prop-
erties when the sensor is installed horizontally (Fig. 7).
Fig. 7: Promass F, E, H installed horizontally
1 Not suitable for fluids with entrained solids. Risk of solids accumulating.
2 Not suitable for outgassing fluids. Risk of gas accumulating.
3.2.4 Heating
Some fluids require suitable measures to avoid loss of heat at the sensor. Heating can
be electric, e.g. with heated elements, or by means of hot water or steam pipes made
of copper.
"Caution:
•Risk of electronics overheating! Consequently, make sure that the adapter between
sensor and transmitter and the connection housing of the remote version always
remain free of insulating material. Note that a certain orientation might be required,
depending on the fluid temperature (See Section 3.2.3 “Fluid temperature”).
•With a fluid temperature between 200...350 °C, heating is not permitted for the com-
pact version of the high-temperature version.
•When using electrical heat tracing whose heat is regulated using phase control or by
pulse packs, it cannot be ruled out that the measured values are influenced by mag-
netic fields which may occur, i.e. at values greater than those permitted by the EC
standard (Sinus 30 A/m). In such cases, the sensor must be magnetically screened
(except for Promass M).
The secondary containment can be shielded with tin plates or electric sheets without
privileged direction (e.g. V330-35A) with the following properties:
– Relative magnetic permeability µr≥300
– Plate thickness d ≥0.35 mm
F06-xxxxxxxx-11-00-00-xx-003

PROline Promass 80 3 Installation
Endress+Hauser 19
•Information on permissible temperature ranges → Page 88.
Special heating jackets which can be ordered as accessories from Endress+Hauser are
available for the sensors.
3.2.5 Thermal insulation
Some fluids require suitable measures to avoid loss of heat at the sensor. A wide range
of materials can be used to provide the required thermal insulation.
Fig. 8: In the case of the Promass F high-temperature version, a maximum insulation thickness of 60 mm
must be observed in the area of the electronics/neck.
If the Promass F high-temperature version is installed horizontally (with transmitter head
pointing upwards), an insulation thickness of min. 10 mm is recommended to reduce
convection. The maximum insulation thickness of 60 mm must be observed (see Fig. 8).
3.2.6 Inlet and outlet runs
There are no installation requirements regarding inlet and outlet runs. If possible, install
the sensor well clear of fittings such as valves, T-pieces, elbows, etc.
3.2.7 Vibrations
The high oscillation frequency of the measuring tubes ensures that the correct operation
of the measuring system is not influenced by pipe vibrations. Consequently, the sensors
require no special measures for attachment.
3.2.8 Limiting flow
See the information on Page 81 and 89.
max. 60
Esc
Esc
E
-
+
max. 60
F06-83FHTxxx-06-00-xx-xx-001

3 Installation PROline Promass 80
20 Endress+Hauser
3.3 Installation instructions
3.3.1 Turning the transmitter housing
Turning the aluminium field housing
#Warning:
The turning mechanism in devices with EEx d/de or FM/CSA Cl. I Div. 1 classification is
not the same as that described here. The procedure for turning these housings is
described in the Ex-specific documentation.
1. Loosen the two securing screws.
2. Turn the bayonet catch as far as it will go.
3. Carefully lift the transmitter housing as far as it will go.
4. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
5. Lower the housing into position and re-engage the bayonet catch.
6. Retighten the two securing screws.
Fig. 9: Turning the transmitter housing (aluminium field housing)
Turning the stainless steel field housing
1. Loosen the two securing screws.
2. Carefully lift the transmitter housing as far as it will go.
3. Turn the transmitter housing to the desired position (max. 2 x 90° in either direction).
4. Lower the housing into position.
5. Retighten the two securing screws.
Fig. 10: Turning the transmitter housing (stainless steel field housing)
F06-xxxxxxxx-17-06-xx-xx-000F06-xxxxxxxx-17-06-xx-xx-001